Broadcom

BCM5464A1KRBG - Quad-Port Gigabit Ethernet PHY | Broadcom

Артикул: BCM5464A1KRBG ✓ Активен
354-ball BGA Package
MOQ: 1 |

BCM5464A1KRBG Обзор

Broadcom BCM5464A1KRBG is a four-channel Gigabit copper Ethernet PHY supporting 10, 100, and 1000 Mb/s data rates in a 354-ball BGA package. It integrates four physical-layer transceiver channels for copper Ethernet connectivity and is positioned for network-interface, switching, industrial-control, and embedded-communication equipment. The device belongs to Broadcom’s BCM54xx family of 0.13-micrometer Gigabit copper PHY products.

A copper Ethernet PHY is the physical-layer component that translates digital Ethernet data into electrical signaling for transmission over twisted-pair cables and converts received signaling back into digital data. Within a network system, the PHY operates below the MAC and network-interface controller: Ethernet frames are generated above it, while magnetics, connectors, cable, and isolation components connect below it. A multi-channel PHY reduces the number of discrete PHY devices required in multiport equipment.

The BCM5464 provides four 10/100/1000BASE-T channels and supports full-duplex Gigabit operation according to the manufacturer’s BCM5464 product brief. Its consolidated implementation can simplify board partitioning compared with four separate single-channel PHYs. Parallel device availability across Broadcom’s BCM5404, BCM5414, BCM5421, BCM5421S, BCM5424, BCM5434, and BCM5464 products supports platform selection according to port count, media requirements, and system architecture.

Broadcom describes the BCM5464 family as a 0.13-micrometer Gigabit copper PHY optimized for performance, cost, and power in Gigabit copper solutions. That process generation is important when integrating the device: board design must account for high-speed differential routing, controlled impedance, clean power and ground distribution, adequate return paths, and thermal performance characteristic of a large 354-ball BGA.

Typical applications include multiport Ethernet switches, industrial Ethernet gateways, network-interface controllers, routers, digital video equipment, factory automation systems, and embedded platforms requiring several copper Gigabit ports. The device can also participate in designs that combine copper access with other network media when the surrounding controller supports mixed-media aggregation.

The primary design constraint is that BCM5464A1KRBG is a complex, high-pin-count BGA rather than a simple peripheral IC. Its layout should follow the manufacturer’s reference design and pin-assignment documentation, including ball-grid escaping, layer transitions, decoupling, clock requirements, and PHY-to-magnetics spacing. Confirm the exact exposed-pad and thermal-land requirements before releasing artwork.

This page combines the BCM5464 product-brief specifications with application guidance, selection criteria, engineering notes, and verified availability references. It also distinguishes confirmed substitutes from candidates whose package and pin compatibility still require engineering review, helping designers avoid treating merely similar Ethernet PHYs as drop-in replacements.

Аналоги без доработки для BCM5464A1KRBG — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Для этого товара нет аналогов без доработки.

Запросить аналоги

BCM5464A1KRBG Максимальные параметры и электрические характеристики

Product Type Quad-port Gigabit copper Ethernet PHY
Number of Channels 4 channels
Supported Data Rates 10 Mb/s, 100 Mb/s, and 1000 Mb/s per channel
Ethernet Media 10/100/1000BASE-T copper Ethernet
Duplex Support Full duplex
Process Technology 0.13 µm
Device Family BCM54xx Gigabit copper PHY family
Package Type 354-ball BGA
Terminal Count 354 terminals
Package Mounting Type Surface mount
Статус RoHS Unknown
REACH Status Unknown
AEC-Q100 Qualification Not applicable

Руководство по цоколевке BCM5464A1KRBG в корпусе surface mount

Цоколевка для BCM5464A1KRBG (корпус surface mount). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.

Схема цоколевки корпуса surface mount для BCM5464A1KRBG

Нет подробных данных о распиновке для BCM5464A1KRBG.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

BCM5464A1KRBG подходит для 6 применениеs: Multiport Gigabit Ethernet Switch, Industrial Ethernet Gateway, Network Interface Controller, Factory Automation Controller, Embedded Router and Gateway, Digital Video Network Appliance.

🌐

Multiport Gigabit Ethernet Switch

The BCM5464A1KRBG fits a switch or gateway requiring four copper Gigabit Ethernet ports. Its four-channel configuration consolidates the physical-layer transceivers needed for 10/100/1000BASE-T service while leaving frame processing and port arbitration to a compatible switch or MAC controller. In a typical implementation, each PHY channel connects through controlled-impedance traces to Ethernet magnetics and then to a shielded RJ45 or other connector. This arrangement reduces the number of separate copper PHY packages, although the 354-ball BGA still demands careful power delivery, clock distribution, thermal analysis, and high-speed routing. The device is most appropriate when four copper ports are required on the same board and the supporting controller supports the Broadcom PHY interface and register set.

🏭

Industrial Ethernet Gateway

The BCM5464A1KRBG is suitable for an industrial gateway that must expose several 10/100/1000BASE-T service ports to controllers, sensors, supervisory systems, or service equipment. The four PHY channels allow a compact gateway architecture, while the surrounding processor handles protocols, data aggregation, security, and remote management. Industrial implementation requires checking the exact ordering code’s temperature rating and adding the required surge, ESD, isolation, grounding, and enclosure protection. Ethernet magnetics should be selected from the Broadcom-supported design space, and PCB layout should preserve controlled impedance and separation between channels. Firmware must also validate auto-negotiation, link-speed transitions, error counters, and recovery behavior across the operating temperature range and long cable lengths expected in industrial environments.

🖥️

Network Interface Controller

The BCM5464A1KRBG can provide four physical-layer channels for a multiport network-interface controller used in routers, embedded gateways, and communication appliances. The PHY handles physical signaling across copper links, while the host controller or network processor handles packet queues, address tables, traffic management, and control-plane protocols. Because BCM5464A1KRBG is a 354-ball BGA, the design must include a high-density escape strategy, multiple supply rails, low-noise clock distribution, and adequate thermal spreading through the PCB. A reference-design-based layout reduces risk around analog isolation, digital control, and line-side interfaces. Firmware should exercise all supported rates, verify auto-negotiation, monitor PHY registers for link and error events, and define recovery behavior if a channel is disconnected or reinserted during operation.

🤖

Factory Automation Controller

The BCM5464A1KRBG can support factory automation equipment that connects programmable logic controllers, motion controllers, vision processors, remote I/O, and service tools over copper Ethernet. Four independent 10/100/1000BASE-T channels provide flexibility for machine-to-machine communication and diagnostics without requiring four separate PHY packages. Industrial qualification remains the dominant design concern: confirm the temperature range, maintain deterministic grounding between the PHY, magnetics, and connector, and protect each line from industrial transients. The PCB should keep sensitive digital and clock routes away from line-side surge paths, while retaining continuous reference planes beneath differential pairs. Firmware can use the PHY management interface for link status, speed selection, diagnostics, and controlled shutdown, allowing the automation controller to report network faults without disrupting unrelated machine functions.

📡

Embedded Router and Gateway

The BCM5464A1KRBG is appropriate for embedded routers and communication gateways that expose multiple copper Ethernet links to local equipment while using an internal processor for routing and management. Its four Gigabit channels allow simultaneous service connectivity when link demand justifies the integration. The surrounding design should implement separate clock and supply domains carefully, use low-inductance decoupling close to the relevant BGA balls, and connect the PHY’s management signals to the host controller through appropriately buffered or properly terminated interfaces. Line-side magnetics and connectors must support the intended data rate, isolation, and environmental requirements. Validation should include packet-loop tests at 10 Mb/s, 100 Mb/s, and 1000 Mb/s, cable insertion tests, thermal operation, recovery after link loss, and interoperability testing with representative switches and endpoint equipment.

📺

Digital Video Network Appliance

The BCM5464A1KRBG can serve a digital video appliance that bridges imaging, storage, control, and monitoring networks over copper Ethernet. Four channels support connections to cameras, display controllers, storage systems, and management hosts when those endpoints use 10/100/1000BASE-T. The multi-channel PHY supports a consolidated hardware approach, but video-network quality also depends on correct packet buffering and traffic prioritization in the host controller; PHY selection alone does not guarantee latency or frame throughput. Keep sensitive video and memory circuitry away from line-side protection components, preserve short return paths beneath high-speed traces, and validate radiated emissions because Ethernet magnetics, connectors, switching regulators, and the large BGA can contribute to electromagnetic coupling. Production testing should exercise link negotiation at all supported rates and verify stable operation over the required temperature and cable-length range.

Сводка рекомендуемых товаров

BCM5414 Related Broadcom Gigabit copper PHY family member Используется в: Multiport Gigabit Ethernet Switch, Embedded Router and Gateway BCM5434 Related Broadcom Gigabit copper PHY family member Используется в: Multiport Gigabit Ethernet Switch, Factory Automation Controller, Digital Video Network Appliance LAN7500I-ABZJ-TR Microchip Technology Используется в: Multiport Gigabit Ethernet Switch BCM5404 Related Broadcom Gigabit copper PHY family member Используется в: Industrial Ethernet Gateway, Digital Video Network Appliance BCM5424 Related Broadcom Gigabit copper PHY family member Используется в: Industrial Ethernet Gateway, Embedded Router and Gateway LAN9313I-NZW-TR Microchip Technology Используется в: Industrial Ethernet Gateway BCM5421 Related Broadcom Gigabit copper PHY family member Используется в: Network Interface Controller BCM5421S Related Broadcom Gigabit copper PHY family member Используется в: Network Interface Controller LAN9730-ABZJ-TR Microchip Technology Используется в: Network Interface Controller BCM5464 Base Broadcom four-channel PHY family designation Используется в: Factory Automation Controller KSZ8895FMQTR Microchip Technology Используется в: Factory Automation Controller, Digital Video Network Appliance KSZ8564XKS-14 Site-listed Ethernet interface controller family companion Используется в: Embedded Router and Gateway
What is the Broadcom BCM5464A1KRBG?
The Broadcom BCM5464A1KRBG is a four-channel Gigabit copper Ethernet PHY packaged in a 354-ball BGA. According to the Broadcom BCM5464 product brief, each channel supports 10 Mb/s, 100 Mb/s, and 1000 Mb/s operation, and the family uses 0.13-micrometer process technology for Gigabit copper networking. It is intended for multiport switches, routers, industrial gateways, network-interface equipment, and other systems that require several 10/100/1000BASE-T physical-layer channels in one device.
How many Ethernet ports can BCM5464A1KRBG support?
The BCM5464A1KRBG supports four Gigabit copper Ethernet channels, allowing one device to serve four 10/100/1000BASE-T ports. The Broadcom BCM5464 product brief identifies the device as a four-channel member of the BCM54xx Gigabit copper PHY family. In a complete port implementation, each channel also requires its associated magnetics or coupling network, line-side protection, routing, and connector arrangement. The PHY should therefore be treated as the central active device in a four-channel copper Ethernet interface rather than as a standalone complete network port.
What data rates does BCM5464A1KRBG support?
Each BCM5464A1KRBG channel supports 10 Mb/s, 100 Mb/s, and 1000 Mb/s Ethernet rates. The Broadcom BCM5464 product brief identifies it as a Gigabit copper PHY, and the product listing describes a quad-port 10/100/1000BASE-T device. This rate set allows the PHY to negotiate with 10BASE-T, 100BASE-TX, and 1000BASE-T equipment over copper cabling, subject to the line-side magnetics, cable characteristics, and network configuration used by the complete system.
Where can I download the BCM5464A1KRBG datasheet and product information?
The official Broadcom BCM5464 product brief is available from the manufacturer documentation link on this page. It describes the device as a 0.13-micrometer, four-channel Gigabit copper PHY in the BCM54xx family. The 354-ball package and terminal count are also identified by product listings. For production release, use the complete Broadcom datasheet, hardware design guide, reference schematic, and PCB layout guidance to verify ball assignments, power sequencing, clocking, exposed-pad treatment, and magnetics implementation.
Where is the BCM5464A1KRBG pinout located?
The BCM5464A1KRBG pin and ball assignments should be taken from the complete Broadcom BCM5464 datasheet and package documentation rather than inferred from a distributor listing. The device uses a 354-ball BGA, so a complete 354-entry diagram cannot be reproduced reliably without the manufacturer’s authoritative ball map. This page therefore does not present a synthetic pin list. During hardware design, map power, ground, digital control, clocks, management interfaces, and each copper channel directly to the official ball table and follow the recommended escape-routing pattern.
Is BCM5464A1KRBG suitable for industrial Ethernet equipment?
The BCM5464A1KRBG is functionally suitable for industrial Ethernet systems requiring four 10/100/1000BASE-T channels, subject to temperature, lifetime, isolation, and regulatory requirements. The Broadcom product brief confirms the four-channel Gigabit copper capability, while the specific operating-temperature rating must be checked for the exact ordering code. Industrial designs should also address surge andESD protection, magnetics isolation, grounding, enclosure discharge paths, long cable runs, and production-test requirements beyond the PHY’s basic signaling function.
What is the best drop-in replacement for BCM5464A1KRBG?
No drop-in replacement can be confirmed from the available cross-reference information because the candidate devices lack documented 354-ball pin compatibility and equivalent electrical parameters. Broadcom BCM54140B0KFBG and BCM54180B0IFBG are identified as comparison candidates, while WPCS4317C.B0-900214, WPCS4317C.A0-900054, and DP83864AUT are listed as alternatives; however, a true replacement requires the same package, compatible ballout, equivalent media interface, and comparable operating characteristics. Request engineering review before substituting any of these parts.
What can replace BCM5464A1KRBG in a four-port Ethernet design?
A BCM5464A1KRBG replacement must provide four compatible copper Ethernet channels in the same 354-ball footprint with matching power, clock, management, and line-side connections. The available cross-reference candidates may support related Ethernet functions, but their package and pin compatibility are not established. Consequently, they cannot be described as drop-in replacements. The safest replacement path is to compare the official BCM5464 ball map and electrical characteristics against a manufacturer-confirmed second source or to redesign the interface around a differently packaged four-channel PHY.
BCM5464A1KRBG vs BCM54140B0KFBG — which is better for a multiport design?
BCM5464A1KRBG is the safer choice when an existing design uses its 354-ball Broadcom footprint and requires four 10/100/1000BASE-T channels. BCM54140B0KFBG appears in a direct comparison with BCM5464A1KRBG, but the available information does not establish identical pin compatibility, package dimensions, clocking, or media-interface behavior. Choose BCM54140B0KFBG only after its official documentation confirms every ball-level and power-domain requirement; otherwise it should be treated as a redesign candidate rather than a drop-in replacement.
BCM5464A1KRBG vs BCM54180B0IFBG — is BCM54180B0IFBG a drop-in replacement?
BCM54180B0IFBG is a comparison candidate, not a confirmed drop-in replacement for BCM5464A1KRBG. A direct comparison page identifies differences in series, mounting style, package type, and compliance characteristics, but it does not establish a one-for-one 354-ball pin map. Because even a small difference in analog supply, clock input, management bus termination, reset, channel order, or PHY addressing can prevent operation, use BCM54180B0IFBG only for a new design or after a complete schematic, timing, and package review.
When should I choose BCM5464A1KRBG instead of a single-port Ethernet PHY?
Choose BCM5464A1KRBG when the system needs four copper Gigabit Ethernet channels and consolidating them into one Broadcom PHY offers a clear board-level advantage. The Broadcom product brief confirms four-channel Gigabit copper operation in the BCM54xx family. Compare that consolidation against a discrete multi-PHY design, including BGA routing complexity, power-domain sequencing, magnetics count, thermal management, management firmware, and long-term sourcing. A single-port PHY is preferable only when the required port count is low enough that the four-channel integration is unnecessary.
Is BCM5464A1KRBG suitable for a switch with copper uplink ports?
The BCM5464A1KRBG can support switch or gateway designs that terminate four 10/100/1000BASE-T copper ports, provided the attached Ethernet controller supports the required PHY interface and register model. The device is a physical-layer transceiver, so it does not by itself perform switching, packet routing, address resolution, or protocol processing. A practical design therefore combines BCM5464A1KRBG with an appropriate MAC or switch controller, external magnetics, line protection, clocks, and a thermal-aware power-delivery network.
What power and thermal considerations apply to BCM5464A1KRBG?
The BCM5464A1KRBG requires careful multi-rail power delivery and heat removal because it is a high-performance, 354-ball BGA Ethernet transceiver. The exact supply limits, current consumption, junction-temperature limit, and package thermal resistance must be taken from the complete Broadcom documentation for the precise ordering code. Place local high-frequency decoupling at the appropriate supply balls, provide low-impedance power and ground planes, minimize loop area, inspect current sharing across power balls, and conduct a thermal analysis using actual PCB copper, enclosure airflow, and worst-case network traffic.
How should BCM5464A1KRBG be placed near Ethernet magnetics and connectors?
Place the BCM5464A1KRBG channel circuitry to minimize differential impedance discontinuities and keep high-speed copper routes short, controlled, and referenced to a continuous ground plane. Follow the Broadcom reference layout for ball fanout, analog and digital supply separation, clock routing, and line-side component placement. Maintain the manufacturer’s spacing between PHY channels and magnetics, use a suitable grounding and isolation strategy, and place surge or ESD protection where required without introducing excessive stub length into the high-speed signal path.
How do I buy BCM5464A1KRBG and check its current price and lead time?
Use the Request a Quote form on this page to request the current BCM5464A1KRBG price, stock position, quantity availability, and production lead time. The manufacturer product brief identifies the device as an active member of the BCM5464 family, while availability can change by channel and order quantity. For an official production buy, include your target annual volume, date code requirement, packaging preference, and inspection requirements so the supplier can confirm the exact ordered MPN and delivery plan.

Справочные инженерные данные для BCM5464A1KRBG — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose BCM5464A1KRBG when a new or existing Broadcom-based design needs four 10/100/1000BASE-T channels in a 354-ball BGA and the supporting controller, clocking, magnetics, and firmware are already aligned with the BCM5464 family. Its multi-channel integration can reduce PHY package count, but it is not a simple eight-pin peripheral: the PCB must accommodate a large BGA, multiple supplies, controlled-impedance routing, magnetics, and thermal design. BCM54140B0KFBG or BCM54180B0IFBG should be considered only when their official documentation confirms the required package, ballout, power, clock, management, and media interfaces. WPCS4317C.B0-900214, WPCS4317C.A0-900054, and DP83864AUT are relevant Ethernet alternatives but are not confirmed drop-in replacements. For legacy production, verify exact ordering code, lifecycle status, availability, and change-control requirements before committing a new layout.

Сравнение с аналогами

Параметр Этот товар
Package 354-ball BGA
Brand Broadcom
Product Type Quad-port Gigabit copper Ethernet PHY
Channel Count 4 channels
Supported Data Rates 10 Mb/s, 100 Mb/s, and 1000 Mb/s per channel
Ethernet Media 10/100/1000BASE-T
Process Technology 0.13 µm
Device Family BCM54xx Gigabit copper PHY family

Ключевые отличия

  • Four copper Gigabit channels in one device (против DP83864AUT)
  • Established Broadcom BCM54xx integration family (против BCM54140B0KFBG)
  • Four-channel architecture reduces PHY package count (против WPCS4317C.B0-900214)

Заметки по проектированию

Use the Broadcom reference layout as the baseline for the 354-ball BGA rather than designing a new escape pattern. Preserve uninterrupted ground references beneath every high-speed differential pair, route the four channels with controlled impedance, and avoid plane splits that interrupt return current. Confirm ball assignments, power-ball connectivity, and exposed-pad treatment from the complete package documentation before schematic release. A small change in BGA fanout can degrade power-integrity behavior or introduce unequal insertion loss between copper Ethernet channels.

Treat the analog, digital, and clock-supply domains as separate delivery problems until the official schematic identifies their exact relationships. Place local ceramic decoupling directly at the relevant supply balls, provide low-impedance plane connections, and verify simultaneous four-channel Gigabit operation at the worst-case temperature. Check startup sequencing, current sharing across multiple power balls, and the regulator’s transient response against the exact limits in the complete Broadcom documentation. Do not infer supply values from the product family name or distributor metadata.

Keep each PHY channel’s line-side path symmetrical and electrically short from the BGA through the magnetics to the connector. Follow the manufacturer’s recommended magnetics and component placement, maintain the specified channel spacing, and place surge or ESD protection components where their parasitic capacitance will not materially distort the Ethernet signal. Use a continuous reference plane and controlled-impedance fabrication rules, and inspect the finished assembly for accidental via stubs, impedance discontinuities, and grounding gaps.

Model the BGA’s heat flow with the actual PCB stack-up, copper distribution, enclosure, and expected traffic rather than relying on a generic junction-temperature margin. Distribute return currents across the package’s ground and thermal structures, monitor hot spots during four-port full-rate operation, and verify operation at the maximum ambient temperature required by the product. If the exact ordering code has a limited temperature rating, include thermal throttling, airflow, or enclosure upgrades in the system design instead of treating a room-temperature test as production proof.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The Broadcom product brief does not establish the exact BCM5464A1KRBG ordering code’s environmental declarations. The parts-classification source describes BCM5464 as active, lists a 5A991.b.1 classification, and reports a halogen-free status of not compliant, but that generic record is not sufficient to assign the full ordering-code compliance profile.

Данные проверены: 2026-11-15 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

BCM5464A1KRBG datasheet BCM5464A1KRBG pinout BCM5464A1KRBG datasheet pdf BCM5464A1KRBG equivalent BCM5464A1KRBG replacement BCM5464A1KRBG cross reference BCM5464A1KRBG footprint BCM5464A1KRBG price Broadcom BCM5464A1KRBG BCM5464A1KRBG 354 BGA BCM5464A1KRBG Ethernet PHY BCM5464A1KRBG vs BCM54140B0KFBG BCM5464A1KRBG quad port BCM5464A1KRBG schematic

Связанные компоненты & термины

Broadcom BCM5464A1KRBG BCM5464 BCM54xx BCM54140B0KFBG BCM54180B0IFBG WPCS4317C.B0-900214 WPCS4317C.A0-900054 DP83864AUT Ethernet PHY Gigabit copper PHY physical-layer transceiver 10/100/1000BASE-T Ethernet MAC network interface controller 354-ball BGA BGA package family surface-mount package 0.13-micrometer process differential signaling controlled impedance Ethernet magnetics industrial Ethernet multiport Ethernet switch power management IC
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ