CD4029BK3 - 4-Bit CMOS Up/Down Counter | Texas Instruments
Артикул: CD4029BK3 ✓ АктивенCD4029BK3 Обзор
A CMOS up/down counter is a sequential logic device that increments or decrements its four-bit output on each active clock edge. The direction of counting is selected by a dedicated up/down control, allowing the same counter to count upward, count downward, or stop when the direction input is held in the inactive state. Within the broader electronics hierarchy, the CD4029BK3 belongs to the CMOS 4000 Series of counters, dividers, and arithmetic logic functions.
Key characteristics include four binary counter outputs, preset capability for parallel loading, and operation across a wide 5 V to 18 V supply range. Its positive-edge-triggered architecture makes the counting action occur in response to a rising clock transition. The wide operating-temperature range makes the device suitable for industrial, instrumentation, telecommunications, and legacy control systems where extended environmental capability is required.
The CD4029BK3 operates from the original CD4000 CMOS logic family, whose design uses complementary MOSFET stages rather than bipolar transistor logic. CMOS counters can provide low static power consumption, high noise immunity, and broad supply-voltage operation compared with earlier fixed-voltage TTL implementations. These properties make the device useful when counting events must remain reliable across varying supply conditions or noisy industrial environments.
Typical uses include programmable sequencing, timing and event-counting systems, frequency division, industrial control logic, laboratory instrumentation, and test equipment. The four counter outputs can be decoded into a larger sequence of control states, while the preset and load functions allow a system to start from a programmed value or acquire a parallel-loaded count.
When designing around the CD4029BK3, verify the truth table for the direction, clock, preset, and load controls before connecting external logic. Account for supply decoupling and the propagation delay of the CMOS logic path when determining the maximum usable counting rate in a particular system. Use the manufacturer's pin-description table to assign board traces because the DFP lead assignment must follow the exact package drawing.
This page organizes the device specifications, functional characteristics, sourcing information, compatible-product references, and practical design guidance into one engineering-focused reference. It also distinguishes the verified CD4029BK3 data from package and pin details that require confirmation against the manufacturer documentation.
Аналоги без доработки для CD4029BK3 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с CD4029BK3 (тот же форм-фактор и посадочное место) — отличается по Counting Direction, Logic Family, Package.
CD4029BK
✅ Прямая заменаУточнить цену
Открыть даташит →CD4029BK/3
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
5962R9562101V9A
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
CD4029BK3 Максимальные параметры и электрические характеристики
| Counter Type | 4-bit binary up/down counter |
| Logic Family | CD4000 series CMOS |
| Number of Bits | 4 bit |
| Counting Direction | Bidirectional up/down |
| Triggering Edge | Positive edge |
| Operating Mode | Synchronous |
| Supply Voltage Range | 5 V to 18 V |
| Maximum Frequency | 2 MHz |
| Диапазон рабочих температур | -55°C to 125°C |
| Number of Terminals | 16 |
| Корпус | 16-lead DFP (CDFP16) |
| Тип монтажа | Surface mount |
Руководство по цоколевке CD4029BK3 в корпусе 16-lead dfp (cdfp16)
Цоколевка для CD4029BK3 (корпус 16-lead dfp (cdfp16)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для CD4029BK3.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
CD4029BK3 подходит для 6 применениеs: Programmable Industrial Sequencing, Frequency Division and Event Counting, Laboratory Timing and Measurement, Process Control Retain/Count Logic, Legacy Telecommunications Control, Automated Test Equipment State Control.
Programmable Industrial Sequencing
The CD4029BK3 suits programmable sequencing because its four counter outputs can advance through up to 16 decoded states while a dedicated direction input selects counting up or down. The synchronous, positive-edge-triggered operation keeps state changes aligned with the system clock, and the preset and load functions allow a sequence to begin from a programmed count rather than zero. Its 5 V to 18 V supply range provides useful flexibility in industrial control cabinets, while the -55°C to 125°C rating covers extended-temperature equipment. Verify the control-input truth table and preset priority before sequencing sensitive actuators.
Рекомендуется
Frequency Division and Event Counting
CD4029BK3 can divide an incoming event stream into a lower-rate count or accumulate pulses from a sensor, encoder, or timer. The 2 MHz listed maximum frequency provides a useful ceiling when checking clock-source margin, while the actual operating rate must remain below the level needed for the receiving logic to settle. Bidirectional operation allows the same block to count toward a threshold or back down from a preset value. Use a clean clock source and account for propagation delay when the counted events must be captured at a precise system boundary.
Рекомендуется
Laboratory Timing and Measurement
The CD4029BK3 fits legacy laboratory timing and measurement equipment that requires a four-bit binary state counter with preset capability. Its CMOS implementation supports operation across a 5 V to 18 V supply range, and its -55°C to 125°C specification is useful in temperature-controlled instrument enclosures. The counter outputs can drive range selectors, timing gates, or multiplex decode logic. When designing a new instrument around this device, verify legacy signal levels and available board area because the 16-lead DFP package differs from common modern dual in-line counter packages.
Рекомендуется
Process Control Retain/Count Logic
In process-control equipment, CD4029BK3 can count recipe steps, valve transitions, or completed machine cycles. Preset and parallel-load controls allow a sequence to restart at a defined point, while bidirectional counting supports both forward process phases and reverse recovery sequences. The wide supply range is helpful in mixed legacy control boards, but input and output thresholds must be checked against the attached TTL or CMOS devices. The counter should remain in a defined direction state during reset and load operations to prevent unintended state changes.
Рекомендуется
Legacy Telecommunications Control
CD4029BK3 is applicable to legacy telecommunications equipment requiring a synchronous bidirectional counter for timing, channel sequencing, or control-word generation. Its 5 V to 18 V operating range and broad temperature rating support older line-card environments where supply rails and enclosure temperatures vary. The four binary outputs can be decoded to produce timing enables or channel-selection strobes. Because legacy telecommunications boards commonly combine multiple logic technologies, verify signal compatibility, unused-input states, and reset behavior at the board level before releasing a replacement.
Рекомендуется
Automated Test Equipment State Control
CD4029BK3 can implement test-sequence step counting and programmable timing windows in automated test equipment. A preset count lets the tester begin at a selected step, and the four outputs can be decoded into fixture-control or measurement-enable signals. The 2 MHz listed maximum frequency supports relatively fast state sequencing, although fixture relays and measurement acquisition cycles usually determine the practical rate. Keep drive currents within each output's specified limit and use decoupling near the device when long control traces connect to the counter.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для CD4029BK3 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | CD4029BK | CD4029BK/3 | 5962R9562101V9A |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Renesas Electronics |
| Package | 16-lead DFP (CDFP16) | 16-lead CFP | 16-lead CFP | 16-lead DFP/CFP |
| Counter Function | 4-bit binary up/down counter | 4-bit binary up/down counter | 4-bit up/down counter | Bidirectional counter |
| Terminal Count | 16 | 16 | 16 | 16 |
Ключевые отличия
- Broad legacy CMOS supply and temperature capability (против 5962R9562101V9A)
- Bidirectional counting with program loading (против SN74LS93DR)
- Multi-level counting in a 16-lead package (против SN74LS90DR)
Заметки по проектированию
Do not substitute the counter solely from the function description. Confirm the 16-lead DFP body dimensions, lead pitch, terminal numbering, and pin names against the manufacturer package drawing. The CD4029BK and CD4029BK/3 listings share the counter family and 16-lead package class, but suffix conventions can identify different qualification levels, temperature grades, or sourcing variants.
Place a supply bypass capacitor close to the device and route the power and ground connections carefully to minimize switching noise on this CMOS counter. Keep clock, preset, and load traces away from sensitive analog nodes. Because the published operating range extends from 5 V to 18 V, use the manufacturer's recommended operating conditions rather than assuming that every timing and logic specification remains constant across the full range.
Check the counter's propagation delay against the receiving circuit's setup and hold requirements. The published 2 MHz maximum frequency is not a promise that every board can clock the device at that rate; long traces, slow output loads, temperature, and supply voltage can reduce available margin. Use a defined clock source and leave control inputs in known states during normal operation to avoid spurious count transitions.
Информация о соответствии
The device is a legacy CD4000-series CMOS logic IC, and no explicit RoHS, REACH, halogen-free, or conflict-minerals declarations are stated in the available product information. AEC-Q100 is not applicable because the device is not listed as an automotive-qualified variant.