CD4516BCN - 4-Bit CMOS Binary Up/Down Counter | onsemi
Артикул: CD4516BCN ✓ АктивенCD4516BCN Обзор
A CMOS presettable up/down counter belongs to the counter and divider hierarchy within digital logic ICs. It combines a four-bit state register with direction control, clock synchronization, parallel loading, and preset capability. This allows one counter section to replace several discrete binary-counter stages while also supporting repeatable event sequencing, programmable divide ratios, and state transitions driven by external control signals.
The CD4516BCN provides a straightforward positive-edge counting architecture and through-hole DIP-16 construction. The BCN ordering identifies an onsemi catalog configuration associated with a 16-pin plastic through-hole package and industrial-grade temperature positioning. Because it uses through-hole construction, the device is particularly useful in laboratory instruments, industrial control prototypes, educational equipment, test fixtures, and legacy automation systems where socketed DIP components are easier to assemble, inspect, and replace.
The counter's four-bit width allows each output state to represent one of 16 binary combinations. Its up/down input determines the direction of the next count, while load and preset inputs provide two distinct ways to establish an initial state. These controls are valuable when a counter must begin at a commanded value, hold during an asynchronous loading event, or coordinate counting with another sequential circuit. The positive-edge clock convention also helps ensure that connected logic changes state once per intended clock transition.
Typical applications include divide-by-N event generation, digital timing chains, programmable sequence controllers, industrial counters, batch-processing interfaces, and educational digital-logic systems. The CD4516BCN can operate as the central state element in a multistage counter because its parallel controls make cascading and reloading practical. Designers should account for propagation delays, clock pulse width, reset behavior, and the timing relationship among load, preset, direction, and clock inputs.
For new PCB layouts, verify every signal against the current manufacturer pin description before routing because the DIP-16 footprint alone does not define the counter functions. In through-hole implementations, reserve adequate clearance around the device for insertion and probe access. For systems operating near switching nodes, route clock and control traces away from high-current edges and provide a stable ground reference to prevent unintended transitions.
This page combines the exact catalog identity, verified source links, available package information, application guidance, and a constrained drop-in replacement analysis for the CD4516BCN. The replacement analysis focuses only on same-footprint devices and distinguishes catalog, electrical, and sourcing questions without treating different packages as drop-in alternatives.
Аналоги без доработки для CD4516BCN — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с CD4516BCN (тот же форм-фактор и посадочное место) — отличается по Logic Family, Package Type.
CD4516BE
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →CD4516BCN Максимальные параметры и электрические характеристики
| Product Type | Binary counter IC |
| Counter Elements | 1 element |
| Counting Width | 4 bit |
| Clock Edge | Positive edge |
| Logic Family | CMOS |
| Manufacturer Description | CMOS presettable up/down counter |
| Counting Direction | Up or down |
| Presettable | Yes |
| Package Type | 16-pin through-hole DIP |
| Terminal Count | 16 terminals |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
Руководство по цоколевке CD4516BCN в корпусе rectangular
Цоколевка для CD4516BCN (корпус rectangular). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для CD4516BCN.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
CD4516BCN подходит для 6 применениеs: Industrial Event and Batch Counter, Programmable Divide-by-N Timing Chain, Digital Sequence Controller, Laboratory Timing and Frequency Divider, Legacy Automation Retrofit, Educational Digital Logic Trainer.
Industrial Event and Batch Counter
The CD4516BCN fits industrial event-counting and batch-control circuits because it combines a 4-bit counting width with selectable up or down operation and parallel preset controls. A production fixture can count sensor events, decrement remaining-part positions, or load a new threshold before the next cycle. Its 16-pin through-hole DIP package also simplifies maintenance in legacy equipment. The designer should confirm supply limits and timing behavior from the manufacturer datasheet, then allow for propagation delay between the clock edge and Q-output changes.
Рекомендуется
Programmable Divide-by-N Timing Chain
A CD4516BCN can form a programmable divide-by-N stage in a cascaded timing chain because its parallel load and preset inputs allow a new count value to be established between operating intervals. One counter section may divide a periodic event clock while another section extends the count range. The 4-bit width spans 16 states, and the direction control permits rising or falling sequences. Engineers should account for propagation delay, clock pulse width, and any ripple behavior when combining multiple stages.
Рекомендуется
Digital Sequence Controller
The CD4516BCN is useful in a digital sequence controller because its four parallel outputs represent a compact state value while load and preset inputs allow external logic to reposition the sequence. A controller can advance toward a programmed terminal value, reverse direction, or reload the starting state after a completed operation. The positive-edge trigger helps synchronize state changes to a master clock. For reliable operation, the control inputs must meet setup and hold-time requirements listed in the manufacturer documentation.
Рекомендуется
Laboratory Timing and Frequency Divider
The CD4516BCN can divide a stable input frequency into lower-rate timing pulses for bench instruments, pulse generators, and educational timer modules. Its up/down control provides flexibility when the instrument must count either elapsed events or remaining intervals, while preset permits a repeatable starting value. The through-hole DIP-16 package is convenient for prototyping and socket-based replacement. Validate frequency limits and output transition behavior against the manufacturer datasheet before using it near high-speed sources.
Рекомендуется
Legacy Automation Retrofit
The CD4516BCN is well suited to repairing or extending legacy automation equipment that uses socketed DIP logic and four-bit counting. It can restore a missing event counter, module counter, or programmable step index without changing a through-hole board footprint. The industrial-grade catalog positioning supports use in industrial equipment, although the exact operating limits must be checked against the installation environment. Replacement work should include pin-function verification, supply-voltage measurement, and a functional test of load and preset controls.
Рекомендуется
Educational Digital Logic Trainer
The CD4516BCN provides a clear teaching platform for binary counting, direction control, parallel loading, and synchronous state management. Students can observe four count outputs, load a preset value, and compare up-count and down-count sequences using basic logic instruments. Its DIP-16 form is easy to insert into breadboards and training boards. The experiment should include proper supply bypassing and controlled clocking, while the instructor should emphasize propagation delay and the distinction between preset and load behavior.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для CD4516BCN — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | CD4516BE |
|---|---|---|
| Brand | onsemi | onsemi |
| Package | 16-pin through-hole DIP | 16-pin through-hole DIP |
| Counter Type | Presettable binary up/down counter | Presettable binary up/down counter |
| Counting Width | 4 bit | 4 bit |
| Counter Elements | 1 element | 1 element |
| Clock Edge | Positive edge | Positive edge |
| Logic Family | CMOS | CMOS |
| Mounting Type | Through hole | Through hole |
Ключевые отличия
- Combines four-bit counting, direction control, and parallel initialization (против SN74LS93DR)
- Maintains a practical through-hole migration path (против SN74LS90DR)
- Supports directional event counting in a compact counter section (против CD4516BE)
Заметки по проектированию
Do not infer counter pin assignments from the DIP-16 outline alone. Assign the clock, up/down, load, preset, carry, and four parallel outputs by consulting the CD4516B pin-description table in the manufacturer datasheet. Check each control signal's setup and hold timing relative to the positive clock edge, because incorrect asynchronous-control sequencing can cause an unintended count even when every output appears electrically stable.
For a new through-hole board, follow the manufacturer's DIP-16 footprint and verify clearance for the IC body and solder joints. Place a local bypass capacitor near the supply pins, connect the return path close to the device, and keep clock traces away from high-current switching edges. For repairs, inspect socket contacts and socketed IC legs because intermittent loading or clock connections can resemble a counter failure.
Treat clock and asynchronous control traces as timing-sensitive nets. Keep them short, use a stable ground reference, and avoid routing them parallel to noisy power or relay-control conductors. If the counter drives long cables or noisy electromechanical loads, use suitable buffering or isolation at that interface. The 4-bit output states must be interpreted only after allowing for the propagation delay specified for the selected supply voltage.
Информация о соответствии
The manufacturer and distributor information used for this record does not explicitly state the requested compliance status. AEC-Q100 is not applicable because CD4516BCN is categorized as an industrial logic counter rather than an automotive-qualified device.