DG421DY+ - Dual Latching SPST Switch | Maxim Integrated
Артикул: DG421DY+ ✓ АктивенDG421DY+ Обзор
An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. The DG421DY+ belongs to the analog switch hierarchy, where a CMOS switch is an interface IC used for multiplexing, sampling, test, and signal routing. Its latching control preserves the commanded switch state, making it useful when system logic must remain stable during power-management transitions or when control lines are shared with other bus circuitry.
The two-circuit configuration provides separate 1:1 signal paths rather than a multiplexer arrangement. Guaranteed matching between the two switches limits channel-to-channel variation in on-resistance, while the 4-ohm maximum flatness specification limits resistance changes across the signal range. These characteristics are relevant when attenuation, insertion loss, or signal integrity must remain reasonably consistent between selected channels.
The DG421DY+ is manufactured as a low-power CMOS analog switch using Maxim Integrated's monolithic switch design. Latch-based operation separates the stored control state from the immediate logic level applied to the device. As a result, a control input can be pulsed without unintentionally changing the routing state after the command has been accepted, provided the application observes the timing and supply conditions specified in the manufacturer datasheet.
Typical uses include battery-powered instrumentation, automated test equipment, analog signal multiplexing, sample-and-hold systems, and communication equipment that requires isolated SPST routing. The device can also support circuits where different sensors, amplifiers, or measurement channels must be connected selectively while keeping the routing state stable between control transactions.
Designers should account for supply voltage, input-signal range, switching transients, control timing, and the effect of 35-ohm maximum on-resistance when calculating signal loss. The 16-pin SOP package requires adequate board spacing and careful routing of control and analog traces. Decoupling and grounding practices should follow the application guidance in the Maxim Integrated datasheet.
This product page combines the switch configuration, resistance characteristics, package details, application guidance, and drop-in qualification information into an engineering-oriented reference for analog routing designs.
Аналоги без доработки для DG421DY+ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
DG421DY
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DG421DY+ Максимальные параметры и электрические характеристики
| Number of Circuits | 2 circuits |
| Switch Configuration | 1:1 |
| Switch Type | SPST |
| Maximum On-Resistance | 35 ohm |
| On-Resistance Matching | 3 ohm maximum between switches |
| On-Resistance Flatness | 4 ohm maximum over signal range |
| Process Technology | CMOS |
| Control Method | Latch-based |
| Temperature Grade | Industrial |
| Number of Terminals | 16 terminals |
| Package Code | SOP |
| Package Shape | Rectangular |
| Тип монтажа | Surface mount |
| Manufacturer | Maxim Integrated |
Руководство по цоколевке DG421DY+ в корпусе rectangular
Цоколевка для DG421DY+ (корпус rectangular). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для DG421DY+.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
DG421DY+ подходит для 6 применениеs: Battery-Powered Measurement Systems, Automated Test Equipment, Sensor Signal Multiplexing, Sample-and-Hold Signal Routing, Communication Signal Isolation, Industrial Control Signal Routing.
Battery-Powered Measurement Systems
The DG421DY+ fits battery-powered measurement systems that require two independently switched analog paths and stable routing between control updates. Its latching CMOS control preserves the selected state, while the 35-ohm maximum on-resistance provides a defined basis for calculating insertion loss. According to the Maxim Integrated datasheet, the two channels are 1:1 SPST switches with guaranteed matching of 3 ohms maximum, which helps maintain similar attenuation between selected channels. Place the device close to the sensor or amplifier input, keep analog traces short, and include bypass capacitance and grounding consistent with the manufacturer application guidance.
Рекомендуется
Automated Test Equipment
The DG421DY+ can route two test signals in automated test equipment when a compact SPST connection and latching control are preferred. Its two independent 1:1 circuits allow a fixture to isolate or connect a measurement path, while 3-ohm maximum matching between switches limits channel-dependent error. The 35-ohm maximum on-resistance must be included in the expected signal attenuation, especially for high-impedance sources. Keep the analog routing compact, separate control traces from sensitive inputs, and follow the Maxim Integrated datasheet for supply bypassing and control timing.
Рекомендуется
Sensor Signal Multiplexing
The DG421DY+ is appropriate for two-channel sensor multiplexing when each sensor must be connected to a common analog front end through an SPST path. Latching control helps preserve the selected channel between system updates, and the guaranteed 3-ohm maximum switch-to-switch matching limits channel-to-channel resistance variation. According to the Maxim Integrated datasheet, the maximum on-resistance is 35 ohms and flatness is 4 ohms maximum over the signal range. Account for this resistance in the transducer excitation and input-impedance budget, and maintain a quiet return path to reduce coupling into high-impedance sensor nodes.
Рекомендуется
Sample-and-Hold Signal Routing
The DG421DY+ can connect or disconnect an analog source in a sample-and-hold front end where two SPST paths and latching state are useful. The 35-ohm maximum on-resistance contributes directly to source attenuation and should be compared with the sampling capacitor's effective input impedance. The manufacturer datasheet also specifies 3-ohm maximum matching between switches and 4-ohm maximum flatness, allowing more consistent behavior across the two routes. Place the switch near the sampling network, use short grounded traces, and control switching transients so they do not couple into the held capacitor node.
Рекомендуется
Communication Signal Isolation
The DG421DY+ is suitable for isolating one of two communication or instrumentation lines through SPST routing. Its latching control reduces the need to maintain a continuously asserted command level, while guaranteed matching of 3 ohms maximum supports consistent behavior between the two paths. The 35-ohm maximum on-resistance can create signal attenuation and bandwidth limits, so the design should verify that the source impedance and operating frequency remain acceptable. Keep return paths continuous, use a controlled ground reference, and place the switch close to the protected signal path to limit pickup on long traces.
Рекомендуется
Industrial Control Signal Routing
The DG421DY+ supports industrial control boards that need two isolated analog routing paths with a retained command state. Its industrial temperature grade, surface-mount 16-pin SOP package, and CMOS implementation align with compact embedded control systems. According to the Maxim Integrated datasheet, the switch provides 1:1 SPST paths, 35-ohm maximum on-resistance, and guaranteed matching and flatness characteristics for predictable routing behavior. Designers should still verify the exact operating voltage and temperature limits, protect external control lines from inappropriate transients, and use the pin-description table to implement supply and ground connections correctly.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DG421DY+ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DG421DY |
|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated |
| Package | 16-SOIC | 16-SOIC - same |
| Number of Circuits | 2 circuits | 2 circuits |
| Switch Configuration | 1:1 | 1:1 |
| Switch Type | SPST | SPST |
| Maximum On-Resistance | 35 ohm | 35 ohm |
| On-Resistance Matching | 3 ohm maximum between switches | 3 ohm maximum between switches |
| On-Resistance Flatness | 4 ohm maximum over signal range | 4 ohm maximum over signal range |
| Process Technology | CMOS | CMOS |
| Control Method | Latch-based | Latch-based |
Ключевые отличия
- Two latching SPST circuits in one package (против DG419DY+)
- Guaranteed channel-to-channel resistance matching (против DG421DY)
- Signal-range resistance flatness (против DG421DY)
Заметки по проектированию
Place the DG421DY+ close to the switched analog node so the 35-ohm maximum on-resistance is not compounded by PCB trace resistance. Keep input and output analog paths short and pair them with a continuous ground reference. Route latch-control signals away from sensitive analog conductors to reduce coupling from control transitions into the selected channel.
Do not treat the DG423 or DG425 family diagrams as substitutes for the DG421 pin description; the switch configurations differ even though the devices share a family designation. Use the Maxim Integrated datasheet to identify supply, ground, control, and analog terminals. Also verify the control pulse width and latch behavior before assuming that a momentary command can be used safely.
Include the 35-ohm maximum on-resistance in the source-load and attenuation calculation, then check bandwidth against the switch impedance and parasitic capacitance. For sampling nodes, account for both the switch resistance and the load presented by the capacitor or amplifier input. The 3-ohm maximum matching and 4-ohm maximum flatness figures help assess channel variation but do not remove the need for an application-specific impedance analysis.
Информация о соответствии
The Maxim Integrated datasheet identifies an industrial-temperature CMOS analog switch, but it does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.