DG441DY+T - Quad SPST Analog Switch, 16-SOIC | Analog Devices
Артикул: DG441DY+T ✓ АктивенDG441DY+T Обзор
An analog switch is a semiconductor device that routes an analog signal between terminals under digital control. The DG441 family belongs to the switch and multiplexer hierarchy, where an analog switch provides one independently controlled connection per channel. Unlike a mechanical relay, the DG441DY+T changes connection state electronically with low actuation delay, making it appropriate for high-speed signal selection where the signal bandwidth remains below the switch's switching capabilities.
Each of the four channels is a normally closed SPST arrangement, and the control inputs are compatible with TTL and CMOS logic. The DG441 includes an internal voltage reference for its logic thresholds, helping the device operate predictably across compatible supply conditions. Vishay documentation describes the DG441 family as a low-on-resistance, high-speed CMOS switch intended as a drop-in replacement for the DG201A and DG202 series.
Typical uses include audio-signal routing, sample-and-hold circuits, battery-powered instrumentation, communication systems, and general analog signal multiplexing. The four independent switches allow one package to route several signals without sharing a common drain. Maximum signal amplitude and supply combinations should remain within the ratings published in the manufacturer data sheet because the analog switch is not a substitute for an input protection network.
The 16-SOIC package provides ample pin spacing for manual assembly and conventional PCB routing. Place each switched signal trace away from high-energy digital and switching-node traces, and route the four control inputs directly to their drivers to avoid capacitive coupling during switching transitions. Decoupling capacitors should be placed near the supply pins, while unused control inputs must be driven to a defined logic level rather than left floating.
This page combines the DG441 family electrical characteristics, package information, drop-in alternatives, and application-specific design guidance to help engineers compare the DG441DY+T against equivalent quad SPST analog switches without relying on a distributor summary alone.
Аналоги без доработки для DG441DY+T — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DG441DY+T (тот же форм-фактор и посадочное место) — отличается по Package, Bipolar Supply Range, Logic Input Compatibility, On-Resistance, Switch Configuration.
DG441DYZ
✅ Прямая заменаУточнить цену
Открыть даташит →ADG441Y
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DG441DY-T1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DG441DY-T1-E3
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DG441DYZ
✅ Прямая заменаУточнить цену
Открыть даташит →DG441DY-T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DG441DY+T Максимальные параметры и электрические характеристики
| Number of Switches | 4 |
| Switch Configuration | 1:1 SPST |
| On-Resistance | 85 ohm |
| Typical On-Resistance | 50 ohm |
| Positive Supply Range | +10 V to +30 V |
| Bipolar Supply Range | ±4.5 V to ±20 V |
| Turn-On Time | Less than 250 ns |
| Turn-Off Time | Less than 170 ns |
| Logic Input Compatibility | TTL and CMOS |
| Internal Reference | Voltage reference for logic thresholds |
| Process Technology | 44 V silicon-gate CMOS |
| Корпус | 16-SOIC, 0.154 inch body width |
| Package Length | 3.90 mm |
| Тип монтажа | Surface mount |
| Channel Count | 4 independent channels |
| Legacy Compatibility | Drop-in replacement for DG201A and DG202 series devices |
Руководство по цоколевке DG441DY+T в корпусе 3.90 mm
Цоколевка для DG441DY+T (корпус 3.90 mm). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для DG441DY+T.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
DG441DY+T подходит для 6 применениеs: Audio-Signal Routing, Sample-and-Hold Circuits, Battery-Powered Instrumentation, Communication Signal Multiplexing, Legacy DG201A and DG202 Upgrades, Automated Test Equipment.
Audio-Signal Routing
The DG441DY+T fits four-channel audio selection because it provides four independent SPST routes and completes turn-off in less than 170 ns. Each normally closed channel can connect a source to a downstream amplifier or measurement input, while the TTL/CMOS-compatible control inputs support ordinary digital logic drivers. The 85 ohm nominal on-resistance is acceptable for many line-level and low-impedance audio paths, but channel matching and frequency-response limits must be checked from the family data sheet. Keep the switched node physically separated from motor, relay, and switching-regulator traces to prevent transient noise from coupling into the audio path.
Рекомендуется
Sample-and-Hold Circuits
The DG441DY+T can implement fast sampling paths because turn-on is below 250 ns and turn-off is below 170 ns. The DG441 family documentation specifically identifies reduced charge injection and sample-and-hold use, making the four independent switches suitable for selecting sampling sources or connecting held nodes. In a practical circuit, the control edge, source impedance, and capacitance of the held node determine the real acquisition time. A dedicated low-noise buffer should follow the sampling node, and the control driver should be positioned away from the high-impedance held node to limit digital coupling.
Рекомендуется
Battery-Powered Instrumentation
The DG441DY+T is useful in portable measurement equipment where several low-bandwidth signals must be routed under digital control. Its logic interface supports TTL and CMOS levels, and the family operates from a single +10 V to +30 V source or a bipolar ±4.5 V to ±20 V source. The 16-SOIC package is easy to hand-wire and rework compared with a fine-pitch multichannel package. Because the switch has no active power-management shutdown specification in the family summary, designers should control unused control lines and evaluate the device's operating current against the instrument's battery budget.
Рекомендуется
Communication Signal Multiplexing
The DG441DY+T can route several moderate-bandwidth communication signals through four independent SPST channels without a common drain limitation. Its sub-250 ns turn-on specification and TTL/CMOS-compatible controls suit systems that need rapid source selection under microcontroller or logic-control supervision. The 85 ohm nominal on-resistance contributes insertion loss when the receiving circuit has high input impedance, so account for divider attenuation in the signal budget. High-speed data lines should be impedance-controlled and the analog switch placed so its transitions do not overlap sensitive receive circuitry.
Рекомендуется
Legacy DG201A and DG202 Upgrades
The DG441DY+T is appropriate for upgrading sockets designed for the DG201A or DG202 series because the DG441 family is documented as a drop-in replacement. The migration preserves four independent SPST channels while offering a documented improved 44 V silicon-gate implementation and switching times below 250 ns on and below 170 ns off. Before replacing an installed device, compare maximum signal voltage, supply polarity, control thresholds, leakage, and channel matching. A small rework may still be needed if the legacy assembly used a different pin orientation or socket footprint.
Рекомендуется
Automated Test Equipment
The DG441DY+T can support programmable test-point routing in automated measurement systems because four independent SPST switches provide multiple paths under sequencer control. Sub-170 ns turn-off and sub-250 ns turn-on are useful when reducing path-selection delay between measurement phases. The nominal 85 ohm resistance must be included in the error budget for high-impedance sensors, and leakage should be checked when measuring low-current nodes. Place the device near the routed test points, provide local supply bypassing, and isolate the sensitive analog nodes from relay coils and fast digital edges.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DG441DY+T — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DG441DY | ADG441Y | DG441DY-T1 | DG441DY-T1-E3 | DG441DY |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Vishay Intertechnology | Vishay Intertechnology | Renesas Electronics |
| Number of Switches | 4 | 4 | 4 | 4 | 4 | 4 |
| Switch Configuration | 1:1 SPST | 1:1 SPST | 1:1 SPST | 1:1 SPST | 1:1 SPST | 1:1 SPST |
Ключевые отличия
- Improved four-channel DG441 family construction (против DG441DY)
- Documented legacy socket compatibility (против ADG441Y)
- Fast independently controlled switching (против DG441DY-T1-E3)
Заметки по проектированию
Treat the switched node as a high-impedance analog path when budgeting insertion loss. The nominal 85 ohm on-resistance produces additional attenuation with a finite source and destination impedance, and the DG441 family documentation separately specifies on-resistance matching and flatness. Confirm both curves over the actual signal range before using the switch for precision measurements or audio channels.
Assign every terminal from the complete pin-description table in the DG441 family data sheet and verify orientation against the 16-SOIC footprint. Keep switched analog traces away from digital control edges, relay contacts, inductors, and power-switching nodes. Route each control input directly to its driver so that the high-impedance switch terminals are not exposed to long adjacent control nets.
Use a local bypass capacitor at the supply pins and place it close to the package rather than at the board power-entry point. The device supports single or bipolar supplies, but the correct V+ and V- connections depend on whether the selected channels are referenced to ground or to a negative rail. Confirm signal amplitude and supply polarity against the absolute maximum ratings before energizing the circuit.
Do not leave the four digital control inputs floating. A floating control input can place a channel in an indeterminate state and increase switching transients. Drive every control line to a valid TTL or CMOS level, define its state during reset, and sequence the controls when switching between paths whose output levels differ significantly.
Информация о соответствии
The manufacturer-family documentation does not provide explicit compliance values for this ordering suffix. AEC-Q100 qualification is not indicated for this general-purpose analog switch.