Analog Devices

DG441DY+T - Quad SPST Analog Switch, 16-SOIC | Analog Devices

MPN: DG441DY+T ✓ فعال
+10 V to +30 V Vdss 85 ohm Rds(on) 16-SOIC, 0.154 inch body width Package
MOQ: 1 |

DG441DY+T جائزہ

The Analog Devices DG441DY+T is an improved quad SPST CMOS analog switch in a 16-SOIC package, providing four independent single-pole single-throw switches with a nominal 85 ohm on-resistance rating and 1:1 signal routing. The device accepts a single supply from +10 V to +30 V or a bipolar supply from ±4.5 V to ±20 V, and its switching times are specified below 250 ns for turn-on and below 170 ns for turn-off.

An analog switch is a semiconductor device that routes an analog signal between terminals under digital control. The DG441 family belongs to the switch and multiplexer hierarchy, where an analog switch provides one independently controlled connection per channel. Unlike a mechanical relay, the DG441DY+T changes connection state electronically with low actuation delay, making it appropriate for high-speed signal selection where the signal bandwidth remains below the switch's switching capabilities.

Each of the four channels is a normally closed SPST arrangement, and the control inputs are compatible with TTL and CMOS logic. The DG441 includes an internal voltage reference for its logic thresholds, helping the device operate predictably across compatible supply conditions. Vishay documentation describes the DG441 family as a low-on-resistance, high-speed CMOS switch intended as a drop-in replacement for the DG201A and DG202 series.

Typical uses include audio-signal routing, sample-and-hold circuits, battery-powered instrumentation, communication systems, and general analog signal multiplexing. The four independent switches allow one package to route several signals without sharing a common drain. Maximum signal amplitude and supply combinations should remain within the ratings published in the manufacturer data sheet because the analog switch is not a substitute for an input protection network.

The 16-SOIC package provides ample pin spacing for manual assembly and conventional PCB routing. Place each switched signal trace away from high-energy digital and switching-node traces, and route the four control inputs directly to their drivers to avoid capacitive coupling during switching transitions. Decoupling capacitors should be placed near the supply pins, while unused control inputs must be driven to a defined logic level rather than left floating.

This page combines the DG441 family electrical characteristics, package information, drop-in alternatives, and application-specific design guidance to help engineers compare the DG441DY+T against equivalent quad SPST analog switches without relying on a distributor summary alone.

کے لیے ڈراپ اِن متبادل DG441DY+T — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں DG441DY+T (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Bipolar Supply Range, Logic Input Compatibility, On-Resistance, Switch Configuration.

Analog Devices
Package: 16-lead SOIC
Bipolar Supply Range: +/-4.5 V to +/-20 V
On-Resistance: 85 ohm maximum
موازنہ کریں DG441DY+T →
Renesas Electronics
Package: 16-SOIC (0.154" / 3.90 mm width)
Logic Input Compatibility: TTL and CMOS, with on-chip Vref threshold translator
موازنہ کریں DG441DY+T →

DG441DYZ

✅ ڈراپ-اِن
Renesas Electronics
📦 16-SOIC
SPST (Single-Pole Single-Throw), 4 independent channels · 4 · 85 Ω (typical) · +5 V to +34 V · ±5 V to ±22 V · 44 V (allows 40 Vp-p signals) · 250 ns (typical)

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

ADG441Y

✅ ڈراپ-اِن
📦 16-SOIC
Related 4-channel SPST function in the same footprint; on-resistance, leakage, and lifecycle ratings require comparison

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

DG441DY-T1

✅ ڈراپ-اِن
📦 16-SOIC
Same 4-circuit SPST function and 16-SOIC footprint; temperature grade and ordering code differ

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

DG441DY-T1-E3

✅ ڈراپ-اِن
📦 16-SOIC
Same 4-circuit SPST function with an 85 ohm listed on-resistance; suffix indicates a different ordering variant

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

DG441DYZ

✅ ڈراپ-اِن
Renesas Electronics
📦 16-SOIC
SPST (Single-Pole Single-Throw), 4 independent channels · 4 · 85 Ω (typical) · +5 V to +34 V · ±5 V to ±22 V · 44 V (allows 40 Vp-p signals) · 250 ns (typical)

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

DG441DY-T

✅ ڈراپ-اِن
📦 16-SOIC
Same DG441 family construction and 16-SOIC footprint; ordering suffix and manufacturer differ

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

DG441DY+T زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Number of Switches 4
Switch Configuration 1:1 SPST
On-Resistance 85 ohm
Typical On-Resistance 50 ohm
Positive Supply Range +10 V to +30 V
Bipolar Supply Range ±4.5 V to ±20 V
Turn-On Time Less than 250 ns
Turn-Off Time Less than 170 ns
Logic Input Compatibility TTL and CMOS
Internal Reference Voltage reference for logic thresholds
Process Technology 44 V silicon-gate CMOS
پیکیج 16-SOIC, 0.154 inch body width
Package Length 3.90 mm
ماؤنٹنگ ٹائپ Surface mount
Channel Count 4 independent channels
Legacy Compatibility Drop-in replacement for DG201A and DG202 series devices

DG441DY+T 3.90 mm پن کنفیگریشن گائیڈ

DG441DY+T (3.90 mm پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔

DG441DY+T کے لیے 3.90 mm پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں DG441DY+T.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

DG441DY+T کے لیے موزوں ہے 6 ایپلیکیشنs: Audio-Signal Routing, Sample-and-Hold Circuits, Battery-Powered Instrumentation, Communication Signal Multiplexing, Legacy DG201A and DG202 Upgrades, Automated Test Equipment.

🎧

Audio-Signal Routing

The DG441DY+T fits four-channel audio selection because it provides four independent SPST routes and completes turn-off in less than 170 ns. Each normally closed channel can connect a source to a downstream amplifier or measurement input, while the TTL/CMOS-compatible control inputs support ordinary digital logic drivers. The 85 ohm nominal on-resistance is acceptable for many line-level and low-impedance audio paths, but channel matching and frequency-response limits must be checked from the family data sheet. Keep the switched node physically separated from motor, relay, and switching-regulator traces to prevent transient noise from coupling into the audio path.

🖥️

Sample-and-Hold Circuits

The DG441DY+T can implement fast sampling paths because turn-on is below 250 ns and turn-off is below 170 ns. The DG441 family documentation specifically identifies reduced charge injection and sample-and-hold use, making the four independent switches suitable for selecting sampling sources or connecting held nodes. In a practical circuit, the control edge, source impedance, and capacitance of the held node determine the real acquisition time. A dedicated low-noise buffer should follow the sampling node, and the control driver should be positioned away from the high-impedance held node to limit digital coupling.

🔧

Battery-Powered Instrumentation

The DG441DY+T is useful in portable measurement equipment where several low-bandwidth signals must be routed under digital control. Its logic interface supports TTL and CMOS levels, and the family operates from a single +10 V to +30 V source or a bipolar ±4.5 V to ±20 V source. The 16-SOIC package is easy to hand-wire and rework compared with a fine-pitch multichannel package. Because the switch has no active power-management shutdown specification in the family summary, designers should control unused control lines and evaluate the device's operating current against the instrument's battery budget.

🌐

Communication Signal Multiplexing

The DG441DY+T can route several moderate-bandwidth communication signals through four independent SPST channels without a common drain limitation. Its sub-250 ns turn-on specification and TTL/CMOS-compatible controls suit systems that need rapid source selection under microcontroller or logic-control supervision. The 85 ohm nominal on-resistance contributes insertion loss when the receiving circuit has high input impedance, so account for divider attenuation in the signal budget. High-speed data lines should be impedance-controlled and the analog switch placed so its transitions do not overlap sensitive receive circuitry.

🔄

Legacy DG201A and DG202 Upgrades

The DG441DY+T is appropriate for upgrading sockets designed for the DG201A or DG202 series because the DG441 family is documented as a drop-in replacement. The migration preserves four independent SPST channels while offering a documented improved 44 V silicon-gate implementation and switching times below 250 ns on and below 170 ns off. Before replacing an installed device, compare maximum signal voltage, supply polarity, control thresholds, leakage, and channel matching. A small rework may still be needed if the legacy assembly used a different pin orientation or socket footprint.

🏭

Automated Test Equipment

The DG441DY+T can support programmable test-point routing in automated measurement systems because four independent SPST switches provide multiple paths under sequencer control. Sub-170 ns turn-off and sub-250 ns turn-on are useful when reducing path-selection delay between measurement phases. The nominal 85 ohm resistance must be included in the error budget for high-impedance sensors, and leakage should be checked when measuring low-current nodes. Place the device near the routed test points, provide local supply bypassing, and isolate the sensitive analog nodes from relay coils and fast digital edges.

تجویز کردہ پروڈکٹس کا خلاصہ

DG441DY Related DG441-family audio routing switch استعمال ہوتا ہے: Audio-Signal Routing, Battery-Powered Instrumentation, Legacy DG201A and DG202 Upgrades, Automated Test Equipment ADG441Y Related quad SPST routing switch استعمال ہوتا ہے: Audio-Signal Routing, Communication Signal Multiplexing DG441DY-T1 Related DG441-family sampling switch استعمال ہوتا ہے: Sample-and-Hold Circuits, Legacy DG201A and DG202 Upgrades DG441DY-T1-E3 Related quad SPST sampling switch استعمال ہوتا ہے: Sample-and-Hold Circuits, Automated Test Equipment DG441DY-T Related DG441-family signal router استعمال ہوتا ہے: Communication Signal Multiplexing
What is the DG441DY+T?
The DG441DY+T is an improved quad SPST CMOS analog switch from Analog Devices, formerly Maxim Integrated. It contains four independent normally closed single-pole single-throw switches in a 16-SOIC package. The family operates from a single +10 V to +30 V supply or a bipolar ±4.5 V to ±20 V supply, with turn-on below 250 ns and turn-off below 170 ns.
How many switches are in the DG441DY+T?
The DG441DY+T contains four independent SPST analog switches. Each channel can connect its drain terminal to its source terminal when its corresponding digital control input is asserted. The package has 16 pins, providing the four control connections, four drain connections, four source connections, and supply and ground terminals required for this quad SPST arrangement.
What is the on-resistance of the DG441DY+T?
The DG441DY+T has an 85 ohm nominal on-resistance rating, while the DG441 family documentation also lists 50 ohm typical on-resistance. The exact resistance varies with supply voltage, signal amplitude, and the specific channel. Confirm the maximum on-resistance, matching, and flatness curves in the manufacturer data sheet before designing a precision analog path.
What supply voltages does the DG441DY+T accept?
The DG441DY+T accepts a single supply from +10 V to +30 V or a bipolar supply from ±4.5 V to ±20 V. Its control inputs are compatible with TTL and CMOS logic, and an internal voltage reference establishes the logic thresholds. Keep all connected signal voltages within the absolute maximum ratings shown in the manufacturer data sheet.
How fast does the DG441DY+T switch?
The DG441DY+T switches in less than 250 ns for turn-on and less than 170 ns for turn-off according to the Analog Devices DG441 family product page. These values support fast routing of moderate-bandwidth analog signals. The actual system transition also depends on control-driver rise time, source and drain capacitance, and the impedance of the connected circuit.
Where can I download the DG441DY+T datasheet PDF?
The DG441 family data sheet is available directly from Vishay Siliconix at https://www.vishay.com/docs/70053/dg441.pdf, while the manufacturer product page is available from Analog Devices at https://www.analog.com/en/products/dg441.html. Use the data sheet pin-description table when assigning PCB tracks and confirm the ordering suffix associated with the 16-SOIC package.
Where can I find the DG441DY+T pinout?
The DG441DY+T pinout is defined by the 16-SOIC pin-description table in the DG441 family data sheet at https://www.vishay.com/docs/70053/dg441.pdf. Assign the four control inputs, source and drain pins, supply, and ground exactly as shown there. Do not infer the missing-connection orientation from the package drawing alone; verify each terminal against the complete pin table.
What is the best drop-in replacement for DG441DY+T?
The Renesas DG441DY is a closely matched drop-in choice because it uses the same 16-SOIC DG441 family construction and four independent SPST channels. The Vishay DG441DY-T1-E3 is another 16-SOIC quad SPST option with an 85 ohm on-resistance listing. Confirm on-resistance matching, flatness, logic levels, absolute maximum ratings, and lifecycle requirements against the original design before production substitution.
Can DG441DY+T replace DG201A and DG202 devices?
Yes, the DG441 family is documented as a drop-in replacement for the popular DG201A and DG202 series devices. That compatibility applies to the DG441 family pinout and switching function, while the DG441DY+T represents its improved 16-SOIC ordering variant. Signal amplitude, bandwidth, supply voltage, and control logic must still be reviewed before using the replacement in an existing socket.
What is the difference between DG441DY+T and ADG441?
The DG441DY+T is the improved DG441 quad SPST family in a 16-SOIC package, while the ADG441 is a related Analog Devices quad SPST analog switch with an updated product family identity. Cross-reference listings identify ADG441 as an equivalent function, but production substitution should confirm pin naming, supply ratings, on-resistance limits, leakage, switching time, and fail-safe behavior in the current data sheets.
When should I choose the DG441DY+T over another quad SPST switch?
Choose the DG441DY+T when a design requires four independent, normally closed SPST channels with TTL or CMOS control and a 16-SOIC footprint. It is especially relevant to upgrades from DG201A or DG202 sockets and to audio, sample-and-hold, communication, and battery-powered analog routing. Select another member of the DG441 family if RoHS status, temperature grade, or production lifecycle better matches the project.
Is the DG441DY+T suitable for audio-signal routing?
Yes, the DG441DY+T is suitable for audio-signal routing because the DG441 family is specifically identified for that application and provides four independently controlled SPST channels with sub-microsecond switching. Keep the switched signal within the device's maximum analog input rating, observe the on-resistance matching and flatness limits, and avoid routing the audio trace beside high-current switching nodes.
What can replace the DG441DY+T in a pin-compatible design?
Several 16-SOIC DG441-family devices can be evaluated as pin-compatible replacements, including the Renesas DG441DY, Vishay DG441DY-T1, Vishay DG441DY-T1-E3, and Analog Devices ADG441. Compatibility means the same footprint and terminal arrangement, not identical behavior across every operating condition. Review voltage ratings, channel polarity, leakage, on-resistance matching, logic thresholds, and qualification requirements before substitution.
Is the DG441DY+T the same as the DG441DY?
The DG441DY+T and DG441DY belong to the same improved quad SPST DG441 family and are listed as functionally replaceable in 16-SOIC packages. Cross-reference information describes their terminals and packages as consistent, allowing replacement without PCB modification. Ordering-suffix and manufacturer changes can still affect temperature grade, packaging format, compliance documentation, or availability, so verify the specific suffix being substituted.
What are the key specifications of DG441DY+T that engineers should know?
The DG441DY+T combines four independent 1:1 SPST switches, a 16-SOIC package, an 85 ohm nominal on-resistance, and operation from +10 V to +30 V or ±4.5 V to ±20 V. Its turn-on time is below 250 ns and turn-off time is below 170 ns. The control interface accepts TTL and CMOS levels, and the family is also described as a DG201A and DG202 replacement.
Where can I buy DG441DY+T online?
Use the Request a Quote form on this page to request current DG441DY+T availability, volume pricing, and delivery information from XAIPART. The manufacturer product page and authorized distribution listings can also confirm the active 16-SOIC family, but current stock and lead time should be confirmed through the quote process for the exact ordering suffix.

کے لیے انجینئرنگ ریفرنس ڈیٹا DG441DY+T — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the DG441DY+T for a 16-SOIC design that requires four independent normally closed SPST channels, TTL or CMOS control, and compatibility with DG201A or DG202-style signal routing. It is particularly suitable when a documented improved DG441-family implementation is preferred over the older legacy devices. Select DG441DY or ADG441Y when a current Analog Devices family option offers a more convenient lifecycle or ordering arrangement, but compare the complete electrical specifications first. Vishay DG441DY-T1 and DG441DY-T1-E3 are useful same-footprint alternatives when procurement or temperature-grade requirements favor those ordering variants. Renesas DG441DY and DG441DY-T provide another route for maintaining a DG441-family design. For every substitution, verify pin assignment, channel polarity, supply range, on-resistance matching, flatness, leakage, logic thresholds, switching time, and the exact operating temperature grade.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ DG441DY ADG441Y DG441DY-T1 DG441DY-T1-E3 DG441DY
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Brand Analog Devices Analog Devices Analog Devices Vishay Intertechnology Vishay Intertechnology Renesas Electronics
Number of Switches 4 4 4 4 4 4
Switch Configuration 1:1 SPST 1:1 SPST 1:1 SPST 1:1 SPST 1:1 SPST 1:1 SPST

اہم امتیازی خصوصیات

  • Improved four-channel DG441 family construction (بمقابلہDG441DY)
  • Documented legacy socket compatibility (بمقابلہADG441Y)
  • Fast independently controlled switching (بمقابلہDG441DY-T1-E3)

ڈیزائن نوٹس

Treat the switched node as a high-impedance analog path when budgeting insertion loss. The nominal 85 ohm on-resistance produces additional attenuation with a finite source and destination impedance, and the DG441 family documentation separately specifies on-resistance matching and flatness. Confirm both curves over the actual signal range before using the switch for precision measurements or audio channels.

Assign every terminal from the complete pin-description table in the DG441 family data sheet and verify orientation against the 16-SOIC footprint. Keep switched analog traces away from digital control edges, relay contacts, inductors, and power-switching nodes. Route each control input directly to its driver so that the high-impedance switch terminals are not exposed to long adjacent control nets.

Use a local bypass capacitor at the supply pins and place it close to the package rather than at the board power-entry point. The device supports single or bipolar supplies, but the correct V+ and V- connections depend on whether the selected channels are referenced to ground or to a negative rail. Confirm signal amplitude and supply polarity against the absolute maximum ratings before energizing the circuit.

Do not leave the four digital control inputs floating. A floating control input can place a channel in an indeterminate state and increase switching transients. Drive every control line to a valid TTL or CMOS level, define its state during reset, and sequence the controls when switching between paths whose output levels differ significantly.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The manufacturer-family documentation does not provide explicit compliance values for this ordering suffix. AEC-Q100 qualification is not indicated for this general-purpose analog switch.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-16 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

DG441DY+T datasheet DG441DY+T pinout DG441DY+T 16-SOIC DG441DY+T equivalent DG441DY+T replacement DG441DY+T cross reference DG441DY+T price DG441DY+T stock Analog Devices DG441DY+T DG441DY+T vs DG441DY DG441DY+T audio routing quad SPST analog switch 16-SOIC

متعلقہ اجزاء اور اصطلاحات

Analog Devices Maxim Integrated DG441DY+T DG441DY ADG441Y DG441DY-T1 DG441DY-T1-E3 Vishay Siliconix Renesas Electronics quad SPST analog switch analog switch switch and multiplexer interface IC CMOS TTL-compatible control input on-resistance charge injection sample and hold audio signal routing communication systems battery-powered instrumentation 16-SOIC SOIC package family surface-mount package DG201A DG202
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں