DG445CY+ - 4-Channel SPST Analog Switch, 85 Ohm | Analog Devices
Артикул: DG445CY+ ✓ АктивенDG445CY+ Обзор
An analog switch is a semiconductor device that connects or disconnects a signal path under digital control. The DG445CY+ combines four SPST switch functions in one package, reducing the number of discrete components required for sample-and-hold, signal-routing, measurement, and test systems. Its 1:1 organization means each switch provides a single conducting path when enabled, while the normally open configuration provides a defined off state between the signal terminals.
The key verified operating characteristics of the DG445CY+ are its four switch circuits, 1:1 configuration, 85 ohm on-resistance, and 16-SOIC package. These specifications make the device suitable for analog signal isolation, controlled routing between a source and destination, and multiplexing arrangements where the system uses separate control signals. The SOIC package is compatible with conventional surface-mount PCB assembly and is available in a standard industrial component format.
The DG445CY+ should be considered when the design requires multiple analog switching functions in one package and the signal path is not intended to carry high current. Designers should check the complete manufacturer datasheet for supply voltage, control logic levels, leakage current, switching time, channel capacitance, and the complete pin mapping before finalizing a PCB layout or selecting a replacement.
Use the 16-pin SOIC footprint and pin assignments specified by the manufacturer datasheet when placing the device. Keep analog traces short, maintain controlled return paths, and place any required input and output protection close to the switched nodes. For applications requiring a replacement, verify that the substitute has the same SOIC footprint, compatible control polarity, acceptable on-resistance, and equivalent voltage and timing limits rather than relying on package appearance alone.
Аналоги без доработки для DG445CY+ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DG445CY+ (тот же форм-фактор и посадочное место) — отличается по Switch Configuration, Package, Number of Channels, On-Resistance, Technology.
DG445CY
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DG444DJ+
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →DG419DY+
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →DG418DJ+
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →DG408DY+
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →DG445CY+ Максимальные параметры и электрические характеристики
| Number of Switch Circuits | 4 circuits |
| Switch Configuration | 1:1 SPST, normally open |
| On-Resistance | 85 ohm |
| Корпус | 16-SOIC |
| Manufacturer | Maxim Integrated, represented by Analog Devices |
| Device Type | Improved quad SPST analog switch |
| Signal Path Count per Circuit | 1:1 |
| Technology | CMOS analog switch |
| Тип монтажа | Surface mount |
Руководство по цоколевке DG445CY+ в корпусе 16-soic
Цоколевка для DG445CY+ (корпус 16-soic). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для DG445CY+.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
DG445CY+ подходит для 6 применениеs: Analog Signal Routing, Sample-and-Hold Systems, Test and Measurement Equipment, Battery-Powered Instrumentation, Data Acquisition Front Ends, Multiplexer and Muxing Networks.
Analog Signal Routing
The DG445CY+ is suitable for controlled routing of analog signals through four independent 1:1 SPST paths. Its verified 85 ohm on-resistance can be acceptable in measurement, buffering, and instrumentation systems where the source and load impedities are not extremely low. Use each switch as a normally open connection between a signal node and a destination, with a separate control input for the intended path. Before finalizing the design, confirm the control levels, supply voltage, leakage, and switching time in the manufacturer datasheet. The 16-SOIC package also helps reduce board area compared with four separate switch packages.
Рекомендуется
Sample-and-Hold Systems
The DG445CY+ can provide switching functions in sample-and-hold architectures where multiple analog nodes must be connected or isolated under digital control. The four SPST circuits allow a compact implementation when the system needs separate acquisition and routing paths. Because the published records identify 85 ohm on-resistance but do not state leakage, capacitance, or switching time, those values must be checked against the acquisition bandwidth and settling-time requirements. Use the manufacturer truth table to define the control sequence and place switched analog traces away from fast digital control lines.
Рекомендуется
Test and Measurement Equipment
The DG445CY+ is appropriate for test and measurement equipment that requires repeatable analog path isolation between a source, instrument, or load. Its four integrated SPST switches can simplify channel organization while keeping the footprint in a standard 16-SOIC package. The 85 ohm on-resistance should be included in the total source resistance when calculating measurement accuracy and attenuation. Confirm the device's off leakage and switching characteristics in the datasheet before using it for high-impedance nodes, and keep control routing short and isolated from sensitive analog paths to reduce crosstalk.
Рекомендуется
Battery-Powered Instrumentation
The DG445CY+ can support signal isolation in battery-powered instrumentation where the design needs several analog paths without using a separate IC for every switch. The four-channel integration helps reduce component count and PCB area, while the 85 ohm on-resistance is suitable only when the source and load impedities permit the resulting signal degradation. Because power consumption and supply-voltage details are not present in the basic records, verify quiescent current, control current, and operating range in the datasheet. Use a low-leakage design and controlled grounding strategy when handling high-impedance sensors.
Рекомендуется
Data Acquisition Front Ends
The DG445CY+ can be used in data-acquisition front ends to route signals into or out of an analog measurement channel. Four SPST switch circuits provide a compact way to implement channel selection or signal isolation, provided the 85 ohm on-resistance does not materially affect accuracy. Confirm channel capacitance and switching time against the acquisition bandwidth, and place the switch close to the driven node to minimize parasitic capacitance and unwanted coupling. The manufacturer pinout and recommended application circuit should be used as the basis for layout and control sequencing.
Рекомендуется
Multiplexer and Muxing Networks
The DG445CY+ is useful in small multiplexer or routing networks where multiple analog sources must be isolated and connected to a common destination. The four 1:1 SPST circuits can be coordinated by digital control logic, allowing only the intended path to conduct when configured as normally open. The 85 ohm on-resistance contributes to the source impedance seen by the receiving circuit, so it must be included in gain and settling calculations. Verify switch timing and control polarity in the datasheet, and use separate ground returns to minimize injection from control signals.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DG445CY+ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DG445CY | DG444DJ+ | DG419DY+ | DG418DJ+ | DG408DY+ |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
Ключевые отличия
- Four independently packaged switch functions in one IC (против DG445CY)
- Verified on-resistance value (против DG444DJ+)
- Directly identified 16-SOIC footprint (против DG419DY+)
Заметки по проектированию
Place the DG445CY+ close to the analog nodes it switches and route the four switched paths as short, continuous traces. Keep control inputs away from sensitive analog pins, and use a solid ground reference beneath the device. The manufacturer datasheet pinout should be used for the final 16-SOIC footprint and routing plan.
Include the verified 85 ohm on-resistance in the source impedance of every affected signal path. For high-impedance nodes, leakage and capacitance can dominate, so confirm those parameters in the manufacturer datasheet. Add protection or buffering only after checking that the added capacitance does not degrade settling time.
Do not substitute a similarly packaged analog switch solely by footprint. Verify the number of switch circuits, SPST topology, normally open or closed behavior, control polarity, supply range, on-resistance, and timing. The listed alternatives share the 16-SOIC package family, but exact pin compatibility and electrical equivalence still require datasheet confirmation.
Информация о соответствии
The available product records do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Check current manufacturer compliance documentation before regulated use.