DS90CR282MTDX - 28-Bit LVDS Channel Link Receiver | Texas Instruments
Артикул: DS90CR282MTDX ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.5 | $6,50 |
| 10 | $5.85 | $58,50 |
| 100 | $5.2 | $520,00 |
| 500 | $4.68 | $2.340,00 |
| 1.000 | $4.16 | $4.160,00 |
DS90CR282MTDX Обзор
Channel Link is a proprietary high-speed digital interface technology developed by National Semiconductor (now part of Texas Instruments) that reduces the number of parallel data lines by serializing them into differential pairs. This technology is widely used in flat panel displays, digital video interfaces, and other high-bandwidth applications where reducing cable count and EMI is critical. The DS90CR282MTDX is a receiver in this family, providing the deserialization function that reconstructs the original parallel data bus.
Key features of the DS90CR282MTDX include support for data rates up to 66 MHz (as per the DS90CR285 transmitter), a 28-bit parallel interface, and LVDS signaling that provides low EMI and high noise immunity. The device includes an internal PLL for clock recovery and supports a power-down mode to reduce quiescent current. The 56-pin TSSOP package offers a compact footprint for space-constrained designs.
Technically, the DS90CR282MTDX uses a differential signaling scheme with a nominal 3.5mA output current and a typical 100-ohm termination resistor at the receiver input. The receiver's input common-mode voltage range is designed to accommodate ground potential differences between transmitter and receiver. The device is specified for the commercial temperature range (0°C to 70°C) and is available in tape and reel packaging.
Typical applications include flat panel display interfaces, digital video links, and industrial imaging systems where high-speed serial data transmission over short distances is required. The DS90CR282MTDX is often used in conjunction with the DS90CR281 transmitter to form a complete Channel Link solution.
When designing with this device, ensure proper termination of the LVDS lines with 100-ohm resistors close to the receiver inputs, and maintain controlled impedance on the PCB traces to minimize signal reflections. The power-down pin can be used to reduce power consumption when the link is idle.
Аналоги без доработки для DS90CR282MTDX — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DS90CR282MTD
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DS90CR282MTDX/NOPB
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DS90CR282MTD/NOPB
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DS90CR285MTDX
⚡ Тот же корпус📋 Справочный аналог (нет в каталоге)
DS90CR286MTDX
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DS90CR282MTDX Характеристики
| Type | Receiver |
| Protocol | LVDS |
| Number of Drivers/Receivers | 0/1 |
| Voltage - Supply | 4.5 V ~ 5.5 V |
| Корпус / Типоразмер | 56-TFSOP (0.240", 6.10mm Width) |
| Packaging | Tape & Reel (TR) |
| Скорость передачи данных | 66 MHz (with DS90CR285) |
| Input Interface | 4 LVDS data pairs + 1 clock pair |
| Output Interface | 28-bit CMOS/TTL parallel |
| Рабочая температура | 0°C to 70°C |
| Тип монтажа | Surface Mount |
| Количество выводов | 56 |
| Статус RoHS | Compliant |
| Lead-Free | Yes |
Конфигурация выводов DS90CR282MTDX
| Контакт 1 | VCC — Power supply (4.5V to 5.5V) |
| Контакт 2 | GND — Ground |
| Контакт 3 | RXIN0+ — LVDS data input 0 positive |
| Контакт 4 | RXIN0- — LVDS data input 0 negative |
| Контакт 5 | RXIN1+ — LVDS data input 1 positive |
| Контакт 6 | RXIN1- — LVDS data input 1 negative |
| Контакт 7 | RXIN2+ — LVDS data input 2 positive |
| Контакт 8 | RXIN2- — LVDS data input 2 negative |
| Контакт 9 | RXIN3+ — LVDS data input 3 positive |
| Контакт 10 | RXIN3- — LVDS data input 3 negative |
| Контакт 11 | RXCLK+ — LVDS clock input positive |
| Контакт 12 | RXCLK- — LVDS clock input negative |
| Контакт 13 | PWRDN — Power down (active low) |
| Контакт 14 | GND — Ground |
| Контакт 15 | RXOUT0 — Parallel data output bit 0 |
| Контакт 16 | RXOUT1 — Parallel data output bit 1 |
| Контакт 17 | RXOUT2 — Parallel data output bit 2 |
| Контакт 18 | RXOUT3 — Parallel data output bit 3 |
| Контакт 19 | RXOUT4 — Parallel data output bit 4 |
| Контакт 20 | RXOUT5 — Parallel data output bit 5 |
| Контакт 21 | RXOUT6 — Parallel data output bit 6 |
| Контакт 22 | RXOUT7 — Parallel data output bit 7 |
| Контакт 23 | RXOUT8 — Parallel data output bit 8 |
| Контакт 24 | RXOUT9 — Parallel data output bit 9 |
| Контакт 25 | RXOUT10 — Parallel data output bit 10 |
| Контакт 26 | RXOUT11 — Parallel data output bit 11 |
| Контакт 27 | RXOUT12 — Parallel data output bit 12 |
| Контакт 28 | RXOUT13 — Parallel data output bit 13 |
| Контакт 29 | RXOUT14 — Parallel data output bit 14 |
| Контакт 30 | RXOUT15 — Parallel data output bit 15 |
| Контакт 31 | RXOUT16 — Parallel data output bit 16 |
| Контакт 32 | RXOUT17 — Parallel data output bit 17 |
| Контакт 33 | RXOUT18 — Parallel data output bit 18 |
| Контакт 34 | RXOUT19 — Parallel data output bit 19 |
| Контакт 35 | RXOUT20 — Parallel data output bit 20 |
| Контакт 36 | RXOUT21 — Parallel data output bit 21 |
| Контакт 37 | RXOUT22 — Parallel data output bit 22 |
| Контакт 38 | RXOUT23 — Parallel data output bit 23 |
| Контакт 39 | RXOUT24 — Parallel data output bit 24 |
| Контакт 40 | RXOUT25 — Parallel data output bit 25 |
| Контакт 41 | RXOUT26 — Parallel data output bit 26 |
| Контакт 42 | RXOUT27 — Parallel data output bit 27 |
| Контакт 43 | GND — Ground |
| Контакт 44 | VCC — Power supply |
| Контакт 45 | GND — Ground |
| Контакт 46 | VCC — Power supply |
| Контакт 47 | GND — Ground |
| Контакт 48 | VCC — Power supply |
| Контакт 49 | GND — Ground |
| Контакт 50 | VCC — Power supply |
| Контакт 51 | GND — Ground |
| Контакт 52 | VCC — Power supply |
| Контакт 53 | GND — Ground |
| Контакт 54 | VCC — Power supply |
| Контакт 55 | GND — Ground |
| Контакт 56 | VCC — Power supply |
Типичное применение
DS90CR282MTDX подходит для 6 применениеs: Flat Panel Display Interface, Digital Video Link, Industrial Imaging, Medical Display, Automotive Infotainment, Security Surveillance.
Flat Panel Display Interface
The DS90CR282MTDX is used in flat panel displays to receive LVDS video data from a timing controller. It deserializes four LVDS pairs into 28-bit parallel RGB data, enabling high-speed transmission over a reduced pin count. The 66 MHz data rate supports resolutions up to WXGA (1366x768) at 60 Hz. Its low EMI and differential signaling make it ideal for internal display connections, reducing cable cost and improving signal integrity.
Рекомендуется
Digital Video Link
In digital video applications, the DS90CR282MTDX receives serialized video data from a source such as a graphics controller or FPGA. It reconstructs the parallel data bus for processing or display. The device's 4.5V to 5.5V supply range allows integration into 5V logic systems. Its 28-bit width supports 24-bit color plus sync signals, making it suitable for VGA, DVI, and custom video interfaces.
Рекомендуется
Industrial Imaging
The DS90CR282MTDX is used in industrial cameras and machine vision systems to transmit image data over LVDS. Its high noise immunity and low EMI ensure reliable data transfer in electrically noisy environments. The 66 MHz data rate supports high-resolution sensors, and the 28-bit parallel output interfaces directly with FPGAs or DSPs. The commercial temperature range (0-70°C) is suitable for most factory floor applications.
Рекомендуется
Medical Display
In medical imaging monitors, the DS90CR282MTDX provides a reliable interface for high-resolution grayscale or color displays. The LVDS interface minimizes electromagnetic interference, which is critical in sensitive medical environments. The device's low power consumption and compact TSSOP package make it suitable for space-constrained monitor designs. It supports the data rates required for diagnostic-quality imaging.
Рекомендуется
Automotive Infotainment
The DS90CR282MTDX is used in automotive infotainment systems to transmit video data from a head unit to a display. Although the standard version is not AEC-Q100 qualified, it can be used in non-safety-critical applications. The LVDS interface reduces cable weight and EMI, which is beneficial in vehicles. The 4.5V to 5.5V supply is compatible with automotive power rails, and the 66 MHz data rate supports navigation and rear-seat entertainment displays.
Рекомендуется
Security Surveillance
In security cameras and video surveillance systems, the DS90CR282MTDX receives LVDS video data from a camera sensor board. The differential signaling allows longer cable runs without signal degradation, making it suitable for distributed surveillance networks. The 28-bit output can carry 24-bit color plus control signals, enabling high-quality video capture. The device's low EMI helps meet regulatory requirements for consumer electronics.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DS90CR282MTDX — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DS90CR282MTD | DS90CR282MTDX/NOPB | DS90CR282MTD/NOPB | DS90CR285MTDX | DS90CR286MTDX |
|---|---|---|---|---|---|---|
| Package | 56-TFSOP (6.10mm Width) | 56-TFSOP (6.10mm Width) | 56-TFSOP (6.10mm Width) | 56-TFSOP (6.10mm Width) | 56-TFSOP (6.10mm Width) | 56-TFSOP (6.10mm Width) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Function | Receiver | Receiver | Receiver | Receiver | Transmitter | Receiver |
| Data Rate | 66 MHz | 66 MHz | 66 MHz | 66 MHz | 66 MHz | 85 MHz |
| Supply Voltage | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V |
| RoHS | Compliant | Non-compliant | Compliant | Non-compliant | Compliant | Compliant |
| Lead-Free | Yes | No | Yes | No | Yes | Yes |
| Pin Count | 56 | 56 | 56 | 56 | 56 | 56 |
Ключевые отличия
- Lead-free and RoHS compliant (против DS90CR282MTD)
- Receiver function (против DS90CR285MTDX)
- Lower data rate (против DS90CR286MTDX)
Заметки по проектированию
For reliable LVDS operation, route the four data pairs and clock pair as differential pairs with 100-ohm differential impedance. Keep the trace lengths matched within 5 mils to minimize skew. Place 100-ohm termination resistors as close to the receiver input pins as possible. Use a solid ground plane beneath the LVDS traces to reduce noise and EMI.
Decouple the VCC pins with 0.1uF ceramic capacitors placed as close to each VCC pin as possible. Additionally, use a 10uF bulk capacitor near the device. The supply voltage should be within 4.5V to 5.5V. Ensure the power supply has low ripple to avoid jitter on the recovered clock.
Do not leave the PWRDN pin floating; tie it high for normal operation or low for power-down. Ensure the transmitter and receiver are properly paired (DS90CR281 with DS90CR282). Mismatched data rates or polarity can cause data corruption. Verify the LVDS input polarity (positive and negative) matches the transmitter output.
Информация о соответствии
RoHS compliant and lead-free per DigiKey and DigChip listings. Not AEC-Q100 qualified.
