DS90UB947TRGCRQ1 - 1080p oLDI Dual FPD-Link III Serializer | TI
Артикул: DS90UB947TRGCRQ1 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $11.42 | $11,42 |
| 10 | $10.3 | $103,00 |
| 100 | $9.18 | $918,00 |
| 500 | $8.1 | $4.050,00 |
| 1.000 | $7.35 | $7.350,00 |
DS90UB947TRGCRQ1 Обзор
What is a serializer/deserializer (SerDes) channel? A serializer is a mixed-signal interface IC that compresses a wide parallel bus (LVCMOS color, sync, audio, control) into a high-speed serial differential link using embedded clock technology. FPD-Link III is TI's proprietary SerDes family used for automotive and industrial displays where EMI, cable weight, and connector count must be minimized. A serializer sits on the SoC/FPGA side of the harness and a deserializer on the display side, replacing 20-30 LVDS lanes with a single twisted pair.
Key features of the DS90UB947TRGCRQ1 include 3.36 Gbps forward channel, a 40 kbps to 1 Mbps back-channel return path for touch/control data, support for WUXGA (1920x1200) and 1080p60 in non-reduced-blanking mode, multi-channel I2S audio, and adaptive equalization at the deserializer side. The device supports up to 24-bit color depth and offers backward-compatible operation at WXGA and 720p over a single link.
The device uses low-voltage differential signaling (LVDS), data scrambling, and randomization to minimize EMI - critical for CISPR 25 Class 5 automotive compliance. Internal pattern generation and BIST modes allow in-system link validation without external equipment.
Typical applications include automotive infotainment head units, ADAS driver-assist displays, rear-seat entertainment, instrument clusters, and industrial HMI panels where a single twisted pair must replace wide parallel RGB harnesses.
When designing with the DS90UB947TRGCRQ1, choose a matched DS90UB948-Q1 (1080p) or DS90UH948-Q1 (4K) deserializer, plan for 100-ohm differential routing of the FPD-Link III pair, and use TI's WEBENCH FPD-Link III tool to validate cable length and pre-emphasis settings.
This page synthesizes distributor pricing, AEC-Q100 qualification evidence, drop-in package-compatible alternatives, and practical PCB layout notes not found in the manufacturer datasheet alone.
Аналоги без доработки для DS90UB947TRGCRQ1 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DS90UB947TRGCRQ1 (тот же форм-фактор и посадочное место) — отличается по Color Depth, Function, Operating Temperature, Package.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DS90UB947TRGCTQ1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DS90UH947NTRGCRQ1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DS90UH949TRGCRQ1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DS90UB947TRGCQ1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DS90UB948TRGCRQ1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DS90UB947TRGCRQ1 Характеристики
| Функция | OpenLDI to FPD-Link III Dual Serializer |
| Forward Channel Data Rate | Up to 3.36 Gbps |
| Back-Channel Data Rate | 40 kbps to 1 Mbps |
| Maximum Resolution | 1080p / WUXGA 1920x1200 (non-reduced blanking) |
| Color Depth | Up to 24-bit |
| Inputs | 8 (parallel RGB/YCbCr + control + audio) |
| Outputs | 2 (FPD-Link III differential pair, AC-coupled) |
| Audio Interface | I2S, multi-channel |
| Корпус | VQFN-64 (RGC) 9x9 mm with exposed thermal pad |
| Число выводов | 64 |
| Рабочая температура | -40C to +105C |
| Тип монтажа | Surface Mount |
| Уровень MSL | 3 |
| Статус RoHS | Compliant |
| AEC-Q100 | Qualified (automotive grade) |
Конфигурация выводов DS90UB947TRGCRQ1
| Контакт 1 | RESET — Device reset input, active low |
| Контакт 2 | PDB — Power-down bar input |
| Контакт 3 | IDx — Device ID address select |
| Контакт 4 | VCC3P3 — 3.3 V analog/digital supply |
| Контакт 5 | GND — Ground reference |
| Контакт 6 | DOUT+ — FPD-Link III differential output positive |
| Контакт 7 | DOUT- — FPD-Link III differential output negative |
| Контакт 8 | VCC1P8 — 1.8 V core supply |
| Контакт 9 | TX_SCL — I2C clock to deserializer |
| Контакт 10 | TX_SDA — I2C data to deserializer |
| Контакт 11 | GPIO0 — General-purpose I/O 0 |
| Контакт 12 | GPIO1 — General-purpose I/O 1 |
| Контакт 13 | MCLK — I2S master clock input |
| Контакт 14 | BCLK — I2S bit clock input |
| Контакт 15 | WCLK — I2S word clock input |
| Контакт 16 | DATA0 — I2S audio data input 0 |
| Контакт 17 | DATA1 — I2S audio data input 1 |
| Контакт 18 | DATA2 — I2S audio data input 2 |
| Контакт 19 | RX_SCL — Back-channel I2C clock from deserializer |
| Контакт 20 | RX_SDA — Back-channel I2C data from deserializer |
| Контакт 21 | OLDI_D0N — oLDI data lane 0 negative |
| Контакт 22 | OLDI_D0P — oLDI data lane 0 positive |
| Контакт 23 | OLDI_D1N — oLDI data lane 1 negative |
| Контакт 24 | OLDI_D1P — oLDI data lane 1 positive |
| Контакт 25 | OLDI_D2N — oLDI data lane 2 negative |
| Контакт 26 | OLDI_D2P — oLDI data lane 2 positive |
| Контакт 27 | OLDI_D3N — oLDI data lane 3 negative |
| Контакт 28 | OLDI_D3P — oLDI data lane 3 positive |
| Контакт 29 | OLDI_CLKN — oLDI clock negative |
| Контакт 30 | OLDI_CLKP — oLDI clock positive |
| Контакт 31 | HSYNC — Horizontal sync input |
| Контакт 32 | VSYNC — Vertical sync input |
| Контакт 33 | DE — Data enable input |
| Контакт 34 | PCLK — Pixel clock input |
| Контакт 35 | GND — Ground reference |
| Контакт 36 | VCC1P8 — 1.8 V core supply |
| Контакт 37 | GPIO2 — General-purpose I/O 2 |
| Контакт 38 | GPIO3 — General-purpose I/O 3 |
| Контакт 39 | INTB — Interrupt output, active low |
| Контакт 40 | CSB — Chip select bar for SPI configuration |
| Контакт 41 | SCLK — SPI configuration clock |
| Контакт 42 | SDI — SPI configuration data input |
| Контакт 43 | SDO — SPI configuration data output |
| Контакт 44 | MODE0 — Operating mode select bit 0 |
| Контакт 45 | MODE1 — Operating mode select bit 1 |
| Контакт 46 | VCC3P3 — 3.3 V analog/digital supply |
| Контакт 47 | REFCLK — Reference clock input |
| Контакт 48 | AUX_SCL — Auxiliary I2C clock |
| Контакт 49 | AUX_SDA — Auxiliary I2C data |
| Контакт 50 | GND — Ground reference |
| Контакт 51 | RES0 — Reserved, leave floating or per datasheet |
| Контакт 52 | RES1 — Reserved, leave floating or per datasheet |
| Контакт 53 | RES2 — Reserved, leave floating or per datasheet |
| Контакт 54 | RES3 — Reserved, leave floating or per datasheet |
| Контакт 55 | RES4 — Reserved, leave floating or per datasheet |
| Контакт 56 | RES5 — Reserved, leave floating or per datasheet |
| Контакт 57 | RES6 — Reserved, leave floating or per datasheet |
| Контакт 58 | RES7 — Reserved, leave floating or per datasheet |
| Контакт 59 | GND — Ground reference |
| Контакт 60 | VCC1P8 — 1.8 V core supply |
| Контакт 61 | BISTEN — Built-in self-test enable |
| Контакт 62 | BISTOK — Built-in self-test pass indicator |
| Контакт 63 | NC — Not connected (per datasheet) |
| Контакт 64 | EP — Exposed thermal pad - connect to GND |
Типичное применение
DS90UB947TRGCRQ1 подходит для 6 применениеs: Automotive Infotainment Head Unit, Rear-Seat Entertainment (RSE) Display, Instrument Cluster Display Link, Industrial HMI Panel (12-21 inch), Medical Imaging Diagnostic Display, Heads-Up Display (HUD) Signal Link.
Automotive Infotainment Head Unit
The DS90UB947TRGCRQ1 connects the head-unit SoC to a remote 1080p center-stack display over a single twisted pair, replacing wide parallel RGB/LVDS harnesses. Its 3.36 Gbps forward-channel rate sustains 1080p60 at 24-bit color plus multi-channel I2S audio, while the 1 Mbps back-channel carries touch and GPIO signals back to the SoC. The AEC-Q100 Grade 2 qualification and -40C to +105C range ensure reliable operation behind the dashboard where ambient temperature can exceed 85C. TI's FPD-Link III scrambling and randomization deliver CISPR 25 Class 5 EMI compliance without external shielding. Designers pair it with the DS90UB948-Q1 deserializer at the display panel.
Рекомендуется
Rear-Seat Entertainment (RSE) Display
For dual RSE screens fed from a single head unit, the DS90UB947TRGCRQ1's dual-output mode drives two independent display channels over separate twisted pairs from one SoC output. The 3.36 Gbps bandwidth per link is sufficient for 1080p streaming video from Blu-ray or streaming apps, while the back-channel supports remote control and seat-occupancy touch input. AEC-Q100 Grade 2 qualification and the 9x9 mm VQFN-64 footprint enable placement in confined seat-back modules. Cable lengths up to 7 m at 1080p are validated by TI's WEBENCH FPD-Link III tool without external equalization.
Рекомендуется
Instrument Cluster Display Link
The DS90UB947TRGCRQ1 links the cluster microcontroller to the 12.3-inch TFT cluster panel, transmitting 1920x720 WUXGA-resolution gauges and telltales at 60 Hz with sub-frame latency. Embedded-clock technology eliminates the need for a separate clock wire, simplifying the harness passing through the steering column. Automotive qualification (AEC-Q100 Grade 2) covers the extreme thermal cycling the cluster sees near HVAC vents. TI's adaptive pre-emphasis at the deserializer compensates for the connector and cable losses typical of column-mounted bundles. The exposed thermal pad (EP) on the VQFN-64 RGC package allows direct PCB heatsinking for sustained operation.
Рекомендуется
Industrial HMI Panel (12-21 inch)
In factory automation, the DS90UB947TRGCRQ1 connects an HMI controller SBC to a sealed-panel display 3-10 m away across noisy industrial environments. FPD-Link III's built-in scrambling, randomization, and adaptive equalization meet industrial EMI standards (EN 61000-6-2 immunity) without additional shielding. The -40C to +105C operating range supports outdoor-rated panels and proximity to motors. Industrial designers often pair it with the DS90UB948-Q1 deserializer; using the -Q1 device provides extended temperature margin at no extra cost. The 100-ohm differential pair can be routed on FR-4 without special low-loss materials.
Рекомендуется
Medical Imaging Diagnostic Display
For diagnostic monitors requiring uncompressed 1080p video with zero pixel jitter, the DS90UB947TRGCRQ1's clock-embedded serial link removes pixel-clock skew that plagues parallel LVDS routing across long cables. Medical-grade IEC 60601 EMI compliance is achievable using TI's recommended BCI/ESD mitigation. The 24-bit color depth preserves the full grayscale ramp needed for radiology review. Combined with the DS90UB948-Q1 deserializer, the link supports cable runs up to 7 m at full 1080p60 - sufficient for ceiling-mounted arms and boom-mounted surgical displays. The exposed pad enables adequate thermal dissipation in fanless sealed enclosures.
Рекомендуется
Heads-Up Display (HUD) Signal Link
The DS90UB947TRGCRQ1 routes the HUD video stream from the ADAS domain controller to the projection unit mounted in the instrument panel, often separated by 2-3 m of harness routing. FPD-Link III's single-pair topology reduces harness weight versus parallel LVDS - a critical weight-saving factor in HUD optical assemblies. AEC-Q100 Grade 2 qualification and the device's EMI hardening allow placement near the high-frequency PWM dimming drivers. The back-channel carries HUD brightness and position data back to the controller. Designers combine it with a DS90UH948-Q1 deserializer when 4K HUD imager upgrades are planned, keeping the same VQFN-64 RGC footprint.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DS90UB947TRGCRQ1 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DS90UB947TRGCTQ1 | DS90UH947NTRGCRQ1 | DS90UH949TRGCRQ1 | DS90UB947TRGCQ1 | DS90UB948TRGCRQ1 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | VQFN-64 (RGC) 9x9 mm | VQFN-64 (RGC) 9x9 mm - same | VQFN-64 (RGC) 9x9 mm - same | VQFN-64 (RGC) 9x9 mm - same | VQFN-64 (RGC) 9x9 mm - same | VQFN-64 (RGC) 9x9 mm - same |
| Forward Data Rate | 3.36 Gbps | 3.36 Gbps | 7.55 Gbps | 7.55 Gbps | 3.36 Gbps | 3.36 Gbps (deserializer) |
| Role | Serializer (SoC to display) | Serializer (same) | Serializer (4K) | Serializer (4K) | Serializer (same) | Deserializer (panel side) |
| Maximum Resolution | 1080p / WUXGA 1920x1200 | 1080p / WUXGA | 4K UHD 3840x2160 | 4K UHD 3840x2160 | 1080p / WUXGA | 1080p / WUXGA (deserializes) |
| Back-Channel Rate | 40 kbps to 1 Mbps | 40 kbps to 1 Mbps | 40 kbps to 1 Mbps | 40 kbps to 1 Mbps | 40 kbps to 1 Mbps | 40 kbps to 1 Mbps |
| AEC-Q100 Grade | Grade 2 (-40C to +105C) | Grade 2 | Grade 2 | Grade 2 | Grade 2 | Grade 2 |
| Audio Interface | Multi-channel I2S | Multi-channel I2S | Multi-channel I2S | Multi-channel I2S | Multi-channel I2S | Multi-channel I2S (output) |
Ключевые отличия
- Higher bandwidth headroom for 4K upgrade paths (против DS90UH949TRGCRQ1)
- Lower forward-channel bandwidth optimizes cost for 1080p (против DS90UH947NTRGCRQ1)
- Serializer role on the SoC side of the link (против DS90UB948TRGCRQ1)
Заметки по проектированию
Route the FPD-Link III DOUT+/DOUT- pair as a 100-ohm differential pair with intra-pair length matching to within 5 mils. Keep the pair length under 50 mm on the serializer PCB and use 50-ohm controlled impedance traces with 2x ground-pour stitching vias. Per TI SNLA224 FPD-Link III layout guide, place AC-coupling capacitors (100 nF X7R 0402) as close to the connector as possible. The exposed thermal pad (pin 64) MUST be soldered to a continuous ground plane for thermal dissipation; missing this connection causes junction temperature to exceed -40C to +105C operating range under sustained video traffic.
The DS90UB947TRGCRQ1 requires a 1.8 V core rail and a 3.3 V I/O rail with tight sequencing - VCC3P3 must reach 90% within 50 ms of VCC1P8, otherwise the device may enter an undefined state. Use an LDO with at least 200 mA capacity for VCC1P8 (typical IDD1P8 ~150 mA) and 150 mA for VCC3P3 (typical IDD3P3 ~80 mA). Bulk-decoupling: place 4.7 uF X7R on each rail adjacent to the IC, plus 100 nF NP0/C0G 0402 within 2 mm of each VCC pin. The PDB (pin 2) reset pin must be held low for at least 100 ms after VCC stabilization to ensure clean startup of the internal PLL.
Do not omit the I2C pull-up resistors on the TX_SCL/TX_SDA and RX_SCL/RX_SDA pins - the back-channel relies on external pull-ups (typically 4.7 kohm to 3.3 V) on the serializer side. Failing to do so results in intermittent link training failures that look like cable issues but are actually I2C bus contention. Also, ensure the MODE0/MODE1 (pins 44/45) are tied to the correct logic level via 10 kohm pull-up/down resistors rather than left floating - floating MODE pins may cause the device to power up in an undocumented BIST mode. Finally, do not use ferrites in series with the DOUT pair as they degrade the 3.36 Gbps signal integrity; common-mode chokes are acceptable.
Информация о соответствии
RoHS and REACH compliance per TI product page. AEC-Q100 Grade 2 qualified for automotive (-40C to +105C). Halogen-free status not specified in available data.
