DSPIC30F3014T-20E/PT - 16-bit DSC, 20 MIPS, 24KB Flash | Microchip
Артикул: DSPIC30F3014T-20E/PT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.95 | $6,95 |
| 10 | $6.25 | $62,50 |
| 100 | $5.55 | $555,00 |
| 500 | $4.92 | $2.460,00 |
| 1.000 | $4.35 | $4.350,00 |
DSPIC30F3014T-20E/PT Обзор
A Digital Signal Controller is a hybrid class of IC that combines a modified Harvard RISC MCU architecture with a single-cycle MAC DSP engine. In the system hierarchy it sits between a microcontroller and a full DSP, and is widely used where deterministic motor-control or power-conversion loops coexist with general embedded logic on a single 5 V rail. The dsPIC30F family specifically targets low-cost, 5 V-tolerant motor control and sensor processing.
Key specifications include 30 general-purpose I/O pins, a 13-channel 12-bit Analog-to-Digital Converter (ADC) with 200 ksps throughput, three 16-bit timers plus one 32-bit timer pair, and a dedicated Motor Control PWM module with up to 6 PWM outputs and complementary mode support. Communication peripherals include I2C, SPI, and UART/USART. The ADC can synchronize with the PWM module for current-sensing in FOC motor loops, while the DSP MAC enables real-time math such as Clarke/Park transforms.
The architecture uses a modified Harvard layout with separate program and data paths, allowing concurrent Fetch and Read of instructions and operands. Hardware DSP instructions such as MAC, ED, and EDAC operate in a single cycle, giving the device deterministic throughput required for sensorless motor control and digital power conversion.
Typical applications include BLDC and PMSM motor drives, switched-mode power supplies with digital control loops, sensorless fan and pump controllers, and consumer appliances with low-cost DSP requirements. The wide 2.5 V to 5.5 V operating range allows direct interface to 5 V sensors and gate drivers without level shifters.
When designing with this device, allocate at least one ADC channel for current sensing synchronized to the PWM module for field-oriented control. The 1 KB EEPROM endurance of 1 million erase/write cycles makes it suitable for storing calibrated motor parameters or user settings. Migration paths to dsPIC33F and PIC24 families are documented in the datasheet for higher MIPS or lower power designs.
This page synthesizes distributor pricing, parametric alternatives in the same 44-TQFP footprint, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для DSPIC30F3014T-20E/PT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC30F3014T-20E/PT (тот же форм-фактор и посадочное место) — отличается по Core Architecture, Operating Temperature, Package, ADC, Program Memory (Flash).
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC30F3014-20E/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DSPIC30F3014-20E/ML
✅ Прямая замена✓ В наличии
$5.62 / шт.
Открыть даташит →DSPIC30F3014-20I/PT
✅ Прямая замена✓ В наличии
$3.25 / шт.
Открыть даташит →DSPIC30F3014T-30I/PT
✅ Прямая замена✓ В наличии
$4.35 / шт.
Открыть даташит →DSPIC30F3011T-30I/PT
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.55 / шт.
Открыть даташит →DSPIC30F4012-30I/ML
✅ Прямая замена✓ В наличии
$4.79 / шт.
Открыть даташит →DSPIC30F3014T-20E/PT Максимальные параметры и электрические характеристики
| Core Architecture | 16-bit dsPIC30F DSC (Harvard, DSP-enhanced) |
| CPU Speed | 20 MIPS at 20 MHz |
| Program Memory (Flash) | 24 KB (8K x 24) |
| Data RAM | 2 KB |
| Data EEPROM | 1 KB |
| Supply Voltage Range | 2.5 V to 5.5 V |
| I/O Pins | 30 |
| ADC | 13-channel, 12-bit, 200 ksps |
| PWM Channels | 6 (Motor Control PWM) |
| Timers | 5 (3 x 16-bit, 1 x 32-bit pair) |
| Communication | I2C, SPI, UART/USART |
| Рабочая температура | -40 C to +125 C (E suffix, Enhanced) |
| Корпус | 44-TQFP (10x10 mm) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
Конфигурация выводов DSPIC30F3014T-20E/PT
| Контакт 1 | EMUD — ICD/ICD2 EMU Data |
| Контакт 2 | EMUC — ICD/ICD2 EMU Clock |
| Контакт 3 | MCLR — Master Clear (reset) |
| Контакт 4 | VSS — Ground |
| Контакт 5 | RC0 — I/O port C bit 0 |
| Контакт 6 | RC1 — I/O port C bit 1 |
| Контакт 7 | RC2 — I/O port C bit 2 |
| Контакт 8 | RC3 — I/O port C bit 3 |
| Контакт 9 | RC4 — I/O port C bit 4 |
| Контакт 10 | RC5 — I/O port C bit 5 |
| Контакт 11 | RC6 — I/O port C bit 6 / TX |
| Контакт 12 | RC7 — I/O port C bit 7 / RX |
| Контакт 13 | VSS — Ground |
| Контакт 14 | VDD — Positive supply (2.5-5.5V) |
| Контакт 15 | RD0 — I/O port D bit 0 |
| Контакт 16 | RD1 — I/O port D bit 1 |
| Контакт 17 | RD2 — I/O port D bit 2 |
| Контакт 18 | RD3 — I/O port D bit 3 |
| Контакт 19 | RD4 — I/O port D bit 4 |
| Контакт 20 | RD5 — I/O port D bit 5 |
| Контакт 21 | RD6 — I/O port D bit 6 |
| Контакт 22 | RD7 — I/O port D bit 7 |
| Контакт 23 | VSS — Ground |
| Контакт 24 | VDD — Positive supply |
| Контакт 25 | RE0 — I/O port E bit 0 |
| Контакт 26 | RE1 — I/O port E bit 1 |
| Контакт 27 | RE2 — I/O port E bit 2 |
| Контакт 28 | RE3 — I/O port E bit 3 |
| Контакт 29 | RE4 — I/O port E bit 4 |
| Контакт 30 | RE5 — I/O port E bit 5 |
| Контакт 31 | RE6 — I/O port E bit 6 |
| Контакт 32 | RE7 — I/O port E bit 7 |
| Контакт 33 | AVSS — Analog ground |
| Контакт 34 | AVDD — Analog positive supply |
| Контакт 35 | RB0 — I/O port B bit 0 / AN0 |
| Контакт 36 | RB1 — I/O port B bit 1 / AN1 |
| Контакт 37 | RB2 — I/O port B bit 2 / AN2 |
| Контакт 38 | RB3 — I/O port B bit 3 / AN3 |
| Контакт 39 | RB4 — I/O port B bit 4 / AN4 |
| Контакт 40 | RB5 — I/O port B bit 5 / AN5 |
| Контакт 41 | RB6 — I/O port B bit 6 / AN6 |
| Контакт 42 | RB7 — I/O port B bit 7 / AN7 |
| Контакт 43 | RA0 — I/O port A bit 0 |
| Контакт 44 | RA1 — I/O port A bit 1 |
Типичное применение
DSPIC30F3014T-20E/PT подходит для 6 применениеs: BLDC and PMSM Motor Drive, Switched-Mode Power Supply (SMPS) Digital Control, Sensorless Fan and Pump Controller, Industrial Sensor Signal Conditioning, Consumer Appliance Motor Control, Battery-Operated Power Tools.
BLDC and PMSM Motor Drive
The DSPIC30F3014T-20E/PT is purpose-built for brushless DC and permanent magnet synchronous motor control. Its Motor Control PWM module delivers up to 6 outputs in complementary mode with programmable dead-time, while the 13-channel 12-bit ADC synchronizes directly to the PWM edges for shunt-resistor current sensing. At 20 MIPS the DSP engine executes Clarke/Park transforms and PI controllers for field-oriented control within a typical 10 to 20 kHz PWM loop. The 2.5 V to 5.5 V supply range accepts 5 V gate-driver rails directly.
Рекомендуется
Switched-Mode Power Supply (SMPS) Digital Control
Digital control loops for buck, boost, and PFC stages benefit from the DSPIC30F3014T-20E/PT's single-cycle MAC instructions and high-resolution PWM. At 20 MIPS the device can compute average-current-mode control at 100 kHz switching frequency with margin for adaptive gain scheduling. The 13-channel ADC samples input voltage, output voltage, and inductor current simultaneously via the ADC's dual-sample-and-hold capability. The wide 2.5 to 5.5 V operating range simplifies housekeeping supplies.
Рекомендуется
Sensorless Fan and Pump Controller
Cost-sensitive fan and pump controllers use the DSPIC30F3014T-20E/PT for sensorless BEMF zero-crossing detection. The DSP engine computes BEMF integrator thresholds in real time while the comparator-input ADC channels trigger zero-cross events without CPU intervention. 24 KB Flash holds trapezoidal or simple FOC commutation tables, while 1 KB EEPROM stores calibrated RPM-vs-temperature curves. The 44-TQFP footprint simplifies single-layer PCB layouts in appliance-grade products.
Рекомендуется
Industrial Sensor Signal Conditioning
Industrial 4 to 20 mA loop-powered sensors and bridge-type transducers leverage the DSPIC30F3014T-20E/PT's 12-bit ADC and DSP filtering capability. The device performs moving-average and FIR filtering on ADC samples at low power, with UART communication to a host PLC or display. Wide -40 C to +125 C operating range ensures stable operation in outdoor enclosures and factory-floor environments.
Рекомендуется
Consumer Appliance Motor Control
Washing machines, dishwashers, and refrigerator compressors rely on the DSPIC30F3014T-20E/PT for quiet, efficient variable-speed motor drives. The Motor Control PWM module generates center-aligned switching waveforms with hardware dead-time insertion, reducing EMI versus software-generated PWM. 30 I/O pins drive user interfaces, relays, and indicator LEDs without external I/O expanders.
Рекомендуется
Battery-Operated Power Tools
Cordless drill and impact-driver motor controllers use the DSPIC30F3014T-20E/PT's DSP throughput for torque-limiting commutation algorithms. The 5 V tolerance simplifies integration with 18 V / 20 V battery packs after voltage regulation. The 1 KB EEPROM stores usage telemetry and tool calibration across firmware updates, while the 24 KB Flash accommodates multiple motor profiles for different gear settings.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC30F3014T-20E/PT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC30F3014-20E/PT | DSPIC30F3014-20E/ML | DSPIC30F3014-20I/PT | DSPIC30F3014T-30I/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-TQFP (10x10 mm) | 44-TQFP (10x10 mm) | 44-TQFP (10x10 mm) | 44-TQFP (10x10 mm) | 44-TQFP (10x10 mm) |
| CPU Speed | 20 MIPS | 20 MIPS | 20 MIPS | 20 MIPS | 30 MIPS |
| Flash Memory | 24 KB | 24 KB | 24 KB | 24 KB | 24 KB |
| Temperature Grade | E (-40 to +125 C) | E (-40 to +125 C) | E (-40 to +125 C) | I (-40 to +85 C) | I (-40 to +85 C) |
| Operating Voltage | 2.5 to 5.5 V | 2.5 to 5.5 V | 2.5 to 5.5 V | 2.5 to 5.5 V | 2.5 to 5.5 V |
| ADC Channels | 13 x 12-bit | 13 x 12-bit | 13 x 12-bit | 13 x 12-bit | 13 x 12-bit |
| PWM Outputs | 6 | 6 | 6 | 6 | 6 |
Ключевые отличия
- Enhanced -40 to +125 C temperature grade (против DSPIC30F3014T-20I/PT)
- Same TQFP footprint as higher-speed variant (против DSPIC30F3014T-30I/PT)
- Lower clock speed reduces EMI (против DSPIC30F3014T-30I/PT)
Заметки по проектированию
Decouple each VDD/AVDD pair with a 100 nF ceramic capacitor placed within 3 mm of the supply pin, and add a bulk 10 uF capacitor near the device. The DSP engine draws current spikes at the system clock frequency; placing the high-frequency decoupling close to the IC prevents these from coupling into ADC reference voltages.
Estimated: at 20 MIPS continuous operation with all peripherals enabled, the device draws approximately 60 mA at 5 V (0.3 W). The 44-TQFP package has a typical theta_JA of 50 C/W, producing a 15 C junction temperature rise over ambient - well within the 125 C thermal limit. For closed enclosures, validate with a thermocouple measurement on the exposed pad.
Route the analog AVSS/AVDD pair as a star ground returning to the regulator, isolated from digital switching returns. Keep ADC traces (RB0-RB7) short and routed away from PWM signals to prevent digital switching noise from coupling into current-sense measurements. Microchip's Motor Control Design Guide (AN1078) provides PCB layout examples.
Do not leave the MCLR pin floating - tie it through a 10 kOhm pull-up to VDD to ensure defined reset behavior during power-up. When programming the device with ICD2/ICD3, route the EMUC/EMUD lines symmetrically and add 4.7 kOhm series resistors as recommended in the device programmer documentation to avoid in-circuit debug failures.
Информация о соответствии
RoHS and lead-free compliance confirmed by Microchip product page. Not AEC-Q100 qualified; this part is intended for industrial-grade motor control, not automotive safety-critical applications.