DSPIC33CK32MP206-E/PT - 100MHz 32KB DSC, TQFP-64 | Microchip
Артикул: DSPIC33CK32MP206-E/PT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $2.37 | $2,37 |
| 10 | $2.25 | $22,50 |
| 100 | $2.1 | $210,00 |
| 500 | $1.98 | $990,00 |
| 1.000 | $1.87 | $1.870,00 |
DSPIC33CK32MP206-E/PT Обзор
A digital signal controller combines the computation power of a digital signal processor with the integrated peripherals and interrupt-driven architecture of a microcontroller. DSCs sit between general-purpose MCUs and dedicated DSPs in the embedded-system hierarchy, and they are the device of choice in digital power conversion, motor control and advanced sensing where tight, deterministic control loops must execute at high sampling rates.
Key features include the single-core 100 MHz dsPIC33CK engine with DSP instructions and barrel shifter, High-Resolution PWM with fine edge resolution for switching converters, a CAN Flexible Data (CAN FD) module for automotive and industrial networking, and three integrated operational amplifiers plus three analog comparators that offload signal conditioning from external components. The -E grade extends operation to +150C ambient, supporting under-hood and high-temperature industrial environments.
Architecture highlights: modified Harvard 16-bit core, Flash with ECC and live-update dual-partition option (family feature), 3.0V to 3.6V operation, and Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. The 5V-tolerant-free 3.3V I/O system interfaces cleanly with standard logic and CAN transceivers.
Typical applications include digital power supplies and PFC stages, brushless DC and PMSM motor control for industrial drives, automotive auxiliaries requiring CAN FD and extended temperature range, and power-factor-corrected LED drivers.
Design consideration: the 100 MHz core requires careful VDD decoupling and clock-source selection; use the internal PLL from an external primary oscillator and budget the -E grade supply voltage range of 3.0V to 3.6V strictly for high-temperature derating.
This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для DSPIC33CK32MP206-E/PT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33CK32MP206-E/PT (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature, CAN Interface, Core Architecture, Data SRAM.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33CK32MP206-I/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DSPIC33CK64MP206-E/PT
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.95 / шт.
Открыть даташит →DSPIC33CK256MP206-E/PT
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33CK64MP206-I/PT
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.68 / шт.
Открыть даташит →DSPIC33CK256MP206-I/PT
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
Уточнить цену
Открыть даташит →DSPIC33CK32MP206-E/PT Максимальные параметры и электрические характеристики
| Core | dsPIC33CK 16-bit DSC |
| Максимальная тактовая частота | 100 MHz (100 MIPS) |
| Program Flash | 32 KB (32K x 8) |
| RAM | 8 KB |
| Напряжение питания | 3.0 V to 3.6 V |
| Рабочая температура | -40C to +150C (Extended, E-grade) |
| Корпус | 64-TQFP (10x10 mm), 0.5 mm pitch |
| Тип монтажа | Surface Mount |
| On-chip Op-Amps | 3 |
| Comparators | 3 |
| CAN Interface | CAN FD (Flexible Data) |
| PWM | High-Resolution PWM |
| Special Peripherals | Peripheral Trigger Generator (PTG) |
| Technology | CMOS |
| Разрядность шины данных | 16 bit |
| Family Series | dsPIC33CK32MP206 |
| Статус RoHS | Compliant |
| Qualification | Automotive / Functional Safety (FuSa) capable family |
Конфигурация выводов DSPIC33CK32MP206-E/PT
| Контакт 1 | MCLR — Master clear reset input |
| Контакт 2 | AN0/VREF+ — Analog input 0 / positive voltage reference |
| Контакт 3 | AN1/VREF- — Analog input 1 / negative voltage reference |
| Контакт 4 | PGED3/AN2 — In-circuit debug data 3 / analog input 2 |
| Контакт 5 | PGEC3/AN3 — In-circuit debug clock 3 / analog input 3 |
| Контакт 6 | AN4 — Analog input 4 |
| Контакт 7 | VDD — Positive supply 3.0V to 3.6V |
| Контакт 8 | VSS — Ground reference |
| Контакт 9 | OSC1/CLKIN — Primary oscillator input / external clock in |
| Контакт 10 | OSC2/CLKOUT — Primary oscillator output / clock out |
| Контакт 11 | PGED1/AN5 — In-circuit debug data 1 / analog input 5 |
| Контакт 12 | PGEC1/AN6 — In-circuit debug clock 1 / analog input 6 |
| Контакт 13 | AN7 — Analog input 7 |
| Контакт 14 | AN8 — Analog input 8 |
| Контакт 15 | VDD — Positive supply |
| Контакт 16 | VSS — Ground reference |
| Контакт 17 | AN9 — Analog input 9 |
| Контакт 18 | AN10 — Analog input 10 |
| Контакт 19 | AN11 — Analog input 11 |
| Контакт 20 | AN12 — Analog input 12 |
| Контакт 21 | AN13 — Analog input 13 |
| Контакт 22 | AN14 — Analog input 14 |
| Контакт 23 | AN15 — Analog input 15 |
| Контакт 24 | VSS — Ground reference |
| Контакт 25 | VDD — Positive supply |
| Контакт 26 | TMS — JTAG test mode select |
| Контакт 27 | TCK — JTAG test clock |
| Контакт 28 | TDI — JTAG test data in |
| Контакт 29 | TDO — JTAG test data out |
| Контакт 30 | PGED2 — In-circuit debug data 2 |
| Контакт 31 | PGEC2 — In-circuit debug clock 2 |
| Контакт 32 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 33 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 34 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 35 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 36 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 37 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 38 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 39 | VSS — Ground reference |
| Контакт 40 | VDD — Positive supply |
| Контакт 41 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 42 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 43 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 44 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 45 | OPA1OUT/OPA1IN+ — Op-amp 1 output / non-inverting input (peripheral pin select) |
| Контакт 46 | OPA1IN- — Op-amp 1 inverting input |
| Контакт 47 | OPA2OUT/OPA2IN+ — Op-amp 2 output / non-inverting input |
| Контакт 48 | OPA2IN- — Op-amp 2 inverting input |
| Контакт 49 | OPA3OUT/OPA3IN+ — Op-amp 3 output / non-inverting input |
| Контакт 50 | OPA3IN- — Op-amp 3 inverting input |
| Контакт 51 | CMP1/CMP2/CMP3 I/O — Comparator input/output (peripheral pin select) |
| Контакт 52 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 53 | RPn digital I/O — Remappable peripheral digital I/O (PWM outputs) |
| Контакт 54 | RPn digital I/O — Remappable peripheral digital I/O (PWM outputs) |
| Контакт 55 | RPn digital I/O — Remappable peripheral digital I/O (PWM outputs) |
| Контакт 56 | RPn digital I/O — Remappable peripheral digital I/O (PWM outputs) |
| Контакт 57 | VSS — Ground reference |
| Контакт 58 | VDD — Positive supply |
| Контакт 59 | RPn digital I/O — Remappable peripheral digital I/O (CAN FD TX/RX) |
| Контакт 60 | RPn digital I/O — Remappable peripheral digital I/O (CAN FD TX/RX) |
| Контакт 61 | SOSCI/RPn — Secondary oscillator input / remappable I/O |
| Контакт 62 | SOSCO/RPn — Secondary oscillator output / remappable I/O |
| Контакт 63 | RPn digital I/O — Remappable peripheral digital I/O |
| Контакт 64 | AVDD/AVSS region — Analog supply/ground pins and reference; see datasheet pin diagram |
Типичное применение
DSPIC33CK32MP206-E/PT подходит для 6 применениеs: Digital Power Supplies and PFC, Brushless DC and PMSM Motor Control, Automotive Auxiliary Systems with CAN FD, High-Temperature Industrial Sensing, LED Drivers and Lighting Control, Wireless Power Transfer and Charging.
Digital Power Supplies and PFC
The DSPIC33CK32MP206-E/PT fits digitally controlled AC-DC and DC-DC power supplies because its 100 MHz core executes current-mode control loops at hundreds of kHz sampling rates while the high-resolution PWM delivers sub-nanosecond effective edge resolution for tight duty-cycle control in PFC and LLC stages. The three on-chip op-amps condition current-shunt signals without external amplifiers, and the three comparators support cycle-by-cycle overcurrent protection with nanosecond latency. Placed as the supervisory and control MCU between the feedback divider and gate drivers, it adds adaptive dead-time and burst-mode features that push light-load efficiency above magnetics-only designs, at the cost of firmware development effort versus a fixed-function controller.
Рекомендуется
Brushless DC and PMSM Motor Control
For sensorless FOC of BLDC and PMSM motors, the DSPIC33CK32MP206-E/PT offers a 100 MIPS core that completes field-oriented control inner loops well within PWM periods, with the integrated op-amps amplifying low-side shunt currents and comparators handling hardware overcurrent trips independent of CPU latency. The high-resolution PWM generates the complementary six-channel gate signals with programmable dead-time, and the PTG autonomously sequences ADC sampling so the core spends cycles on control math rather than peripheral management. In a typical 48V industrial drive the controller sits between isolated gate drivers and current sense networks; the -E grade also permits motor-adjacent mounting where enclosure temperatures reach 125C to 150C.
Рекомендуется
Automotive Auxiliary Systems with CAN FD
The integrated CAN Flexible Data module and -40C to +150C extended temperature rating make the DSPIC33CK32MP206-E/PT suitable for under-hood and high-temperature automotive auxiliaries such as electric water pumps, oil pumps, active grille shutters and HVAC blowers. CAN FD communication reaches up to 8 Mbit/s data phase per the module specification, supporting modern in-vehicle network architectures, while the functional-safety-capable dsPIC33CK family documentation supports ISO 26262 development flows. The controller connects to a CAN transceiver at the vehicle network node and drives a three-phase inverter locally; designers must verify exact AEC-Q100 qualification of the orderable code and budget 3.0V to 3.6V supply regulation from the 12V automotive rail via a pre-regulator.
Рекомендуется
High-Temperature Industrial Sensing
The -E grade operating range to +150C suits sensing and control nodes mounted near furnaces, compressors, injection molders and other heat sources where conventional -40C to +85C silicon cannot survive. The DSPIC33CK32MP206-E/PT reads thermocouples and RTDs through its 12-bit ADC family peripherals, applies gain with the three internal op-amps, and performs linearization math on the 100 MHz DSP core including barrel-shifter-accelerated scaling. Digital output travels over UART, SPI, I2C or CAN to a cooler host controller. Thermal design remains critical: at elevated ambient, junction margin shrinks, so minimize core clock and peripheral loading, and follow Microchip high-temperature design guidance for Flash endurance and VDD window compliance at 3.0V to 3.6V.
Рекомендуется
LED Drivers and Lighting Control
Digitally controlled LED drivers benefit from the DSPIC33CK32MP206-E/PT's high-resolution PWM, which achieves the fine average-current resolution needed to eliminate visible flicker and color shift in tunable-white and RGBW lighting. The 100 MHz core runs constant-current regulation loops at switching frequencies beyond 500 kHz, while integrated comparators provide fast short-circuit protection for the output stage. Communication options including CAN FD and UART support DALI-over-CAN gateways and connected lighting backbones. The controller typically sits between a current-sense shunt, the on-chip op-amp, and external MOSFET gate drivers; using the internal analog reduces BOM cost per luminaire, though designers must manage PWM-generated EMI with careful layout and spread-spectrum dimming techniques.
Рекомендуется
Wireless Power Transfer and Charging
Wireless power transmitter and receiver control demands precise frequency tracking of the resonant tank, which the DSPIC33CK32MP206-E/PT achieves with its 100 MHz core adjusting high-resolution PWM frequency in fine steps while sampling coil current and phase through the on-chip op-amps and ADC. Foreign-object detection algorithms execute on the DSP engine between control iterations, and CAN FD or UART links report status to the system host per Qi-adjacent proprietary protocols. In a typical 5W to 65W transmitter, the DSC drives a class-D power stage through gate drivers with closed-loop frequency and duty control; the -E grade tolerates the elevated ambient inside dense charging enclosures where airflow is minimal and conventional MCUs derate.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33CK32MP206-E/PT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33CK32MP206-I/PT | DSPIC33CK64MP206-E/PT | DSPIC33CK256MP206-E/PT | DSPIC33CK64MP206-I/PT | DSPIC33CK256MP206-I/PT |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (10x10) | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Speed | 100 MHz (100 MIPS) | 100 MHz | 100 MHz | 100 MHz | 100 MHz | 100 MHz |
| Program Flash | 32 KB | 32 KB | 64 KB | 256 KB | 64 KB | 256 KB |
| Operating Temperature | -40C to +150C (E) | -40C to +85C (I) | -40C to +150C (E) | -40C to +150C (E) | -40C to +85C (I) | -40C to +85C (I) |
| CAN Interface | CAN FD | CAN FD | CAN FD | CAN FD | CAN FD | CAN FD |
| Op-Amps / Comparators | 3 / 3 | 3 / 3 | 3 / 3 | 3 / 3 | 3 / 3 | 3 / 3 |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| Relative Price | Baseline (from $2.37 as of 2026-09-23) | Slightly lower | Moderately higher | Substantially higher | Moderately higher | Substantially higher |
Ключевые отличия
- Extended temperature rating to +150C (против DSPIC33CK32MP206-I/PT)
- Lowest cost in same footprint (против DSPIC33CK64MP206-E/PT)
- Integrated analog saves external components (против DSPIC33CK256MP206-E/PT)
- Memory headroom for protocol stacks (против DSPIC33CK32MP206-E/PT (itself))
Заметки по проектированию
Supply the DSPIC33CK32MP206-E/PT from a regulated 3.3V rail within the 3.0V to 3.6V datasheet window. Estimated: at 100 MHz active operation with peripherals enabled, family current draw is typically in the tens of milliamps (confirm exact figure in the datasheet electrical characteristics table), giving roughly 0.1W to 0.2W dissipation. Place a 10 uF bulk capacitor at the board power entry and 0.1 uF ceramics at each VDD/VSS pair within 2 mm of the pins. During operation near +150C ambient, recheck the supply window because regulator output tolerance and LDO dropout shift with temperature.
The TQFP-64 (0.5 mm pitch) layout should follow Microchip's recommended footprint exactly: nominal 0.3 mm-wide traces fanning out from each pad and a solid ground plane on layer 2. Route ICSP programming pins PGD/PGC to a 5-pin header for ICD 4 / PICkit 4 debug access before committing the PCB. Keep the analog inputs (AN0-AN15 and op-amp pins 45-50) away from high-dv/dt PWM traces and gate-driver loops; a local analog ground island tied to the main ground at one point preserves ADC accuracy in motor-control layouts.
Three pitfalls recur with the -E grade. First, do not assume the -E and -I parts are identical above +85C: the extended grade has separate electrical derating tables in the family datasheet, so verify Flash endurance and drive strength at your actual operating temperature. Second, the peripheral pin select (PPS) architecture means most digital pins are remappable - lock your PPS mapping in firmware and review it at every layout change. Third, when migrating code between 32 KB and larger Flash family members, the dual-partition live-update configuration must be set consistently to avoid linker placement errors.
Информация о соответствии
RoHS compliant and lead-free per DigiKey/Mouser listings. The dsPIC33CK family is marketed as Functional Safety (FuSa) capable and offered in automotive-qualified variants; the exact AEC-Q100 status of this ordering code must be confirmed with Microchip. REACH, halogen-free and conflict-minerals declarations: download certificates from Microchip's compliance portal.
