DSPIC33EP64GS506-E/PT - 16-bit DSC, 64KB, Digital Power | Microchip
Артикул: DSPIC33EP64GS506-E/PT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.12 | $6,12 |
| 10 | $5.55 | $55,50 |
| 100 | $4.98 | $498,00 |
| 500 | $4.55 | $2.275,00 |
| 1.000 | $4.15 | $4.150,00 |
DSPIC33EP64GS506-E/PT Обзор
A digital signal controller is a hybrid of a microcontroller (MCU) and a digital signal processor (DSP), combining MCU peripherals and ease of use with DSP math capabilities such as a hardware multiply-accumulate unit and barrel shifter. Within the power-management hierarchy, the dsPIC33EP GS50x family sits at the control layer of digital power systems, replacing analog control loops with firmware-executed feedback loops.
Key features include a 16-bit modified Harvard architecture core, dual-partition Flash with Live Update supporting programming while operating, interconnected high-speed PWM modules with complementary outputs and dead-time control, high-speed 12-bit ADCs with programmable gain amplifiers (PGA), analog comparators, and a 3.3V operating supply from 3.0V to 3.6V. The -E temperature variant is specified from -40C to +125C, running at up to 60 MIPS over that full extended range.
Architecturally, the interconnected PWM, ADC and comparator subsystems allow sub-microcycle latency between current sensing and PWM adjustment, which is essential for multi-loop digital SMPS control. The DSP engine provides single-cycle MAC and 40-bit accumulators for PI and PID control-law computation.
Typical applications include interleaved power factor correction (PFC), DC-DC converters, AC-DC power supplies, LED drivers, and solar micro-inverters.
Design consideration: select the 70 MIPS grade only for the -40C to +85C industrial range; above +85C the device must be derated to 60 MIPS.
This page adds value beyond the datasheet by consolidating drop-in alternatives, pricing tiers, and practical design notes in one place.
Аналоги без доработки для DSPIC33EP64GS506-E/PT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33EP64GS506-E/PT (тот же форм-фактор и посадочное место) — отличается по Package, Core Architecture, DSP Features, Packaging, Qualification.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33EP64GS506-I/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DSPIC33EP64GS506T-I/PT
✅ Прямая замена✓ В наличии
$9.8 / шт.
Открыть даташит →DSPIC33EP64GS504-I/PT
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.35 / шт.
Открыть даташит →DSPIC33EP64GS502-I/PT
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP32GS506-I/PT
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP64GS506-E/PT Максимальные параметры и электрические характеристики
| Core Architecture | 16-bit dsPIC33EP modified Harvard |
| Program Memory | 64KB (64K x 8) Flash |
| Max CPU Speed | 70 MIPS (-40C to +85C); 60 MIPS (-40C to +125C) |
| Напряжение питания | 3.0 V to 3.6 V |
| Корпус | 64-TQFP (10x10 mm), 0.5 mm pitch |
| Рабочая температура | -40C to +125C (E grade) |
| Product Family | dsPIC33EP GS50x digital power DSC |
| Dual Partition Flash | Yes, with Live Update support |
| High-Speed PWM | Interconnected, complementary outputs, dead-time control |
| ADC | High-speed 12-bit with programmable gain amplifier (PGA) |
| Analog Comparators | On-chip, interconnected to PWM |
| DSP Features | Single-cycle MAC, barrel shifter, 40-bit accumulators |
| Тип монтажа | Surface Mount |
| Qualification | Functional Safety (FuSa) capable family |
| In-Circuit Debug | Boundary scan / 2-wire programming (ICSP) |
| Low Power Modes | Yes (Idle, Sleep) |
| Статус RoHS | Compliant |
Конфигурация выводов DSPIC33EP64GS506-E/PT
| Контакт 1 | MCLR — Master clear reset, programming voltage input |
| Контакт 2 | AN0/VREF+/CN2/RB0 — Analog input 0 / positive voltage reference / port B pin 0 |
| Контакт 3 | AN1/VREF-/CN3/RB1 — Analog input 1 / negative voltage reference / port B pin 1 |
| Контакт 4 | AN2/SS1/CN4/RB2 — Analog input 2 / SPI slave select 1 / port B pin 2 |
| Контакт 5 | AN3/INDX/CN5/RB3 — Analog input 3 / QEA index input / port B pin 3 |
| Контакт 6 | AN4/QEA/IC7/CN6/RB4 — Analog input 4 / QEA encoder input / input capture 7 / port B pin 4 |
| Контакт 7 | AN5/QEB/IC8/CN7/RB5 — Analog input 5 / QEB encoder input / input capture 8 / port B pin 5 |
| Контакт 8 | VSS — Ground reference |
| Контакт 9 | OSC1/CLKI/CN30/RC12 — Oscillator crystal input / external clock input / port C pin 12 |
| Контакт 10 | OSC2/CLKO/CN29/RC15 — Oscillator crystal output / clock output / port C pin 15 |
| Контакт 11 | PWM1H1/RE0 — PWM channel 1 high output / port E pin 0 |
| Контакт 12 | PWM1L1/RE1 — PWM channel 1 low output / port E pin 1 |
| Контакт 13 | PWM1H2/RE2 — PWM channel 2 high output / port E pin 2 |
| Контакт 14 | PWM1L2/RE3 — PWM channel 2 low output / port E pin 3 |
| Контакт 15 | PWM1H3/RE4 — PWM channel 3 high output / port E pin 4 |
| Контакт 16 | PWM1L3/RE5 — PWM channel 3 low output / port E pin 5 |
| Контакт 17 | VDD — Power supply (3.0V to 3.6V) |
| Контакт 18 | VSS — Ground reference |
| Контакт 19 | PWM1H4/RE6 — PWM channel 4 high output / port E pin 6 |
| Контакт 20 | PWM1L4/RE7 — PWM channel 4 low output / port E pin 7 |
| Контакт 21 | PWM2H1/RD0 — PWM channel 2 block 1 high output / port D pin 0 |
| Контакт 22 | PWM2L1/RD1 — PWM channel 2 block 1 low output / port D pin 1 |
| Контакт 23 | PWM2H2/RD2 — PWM channel 2 block 2 high output / port D pin 2 |
| Контакт 24 | PWM2L2/RD3 — PWM channel 2 block 2 low output / port D pin 3 |
| Контакт 25 | PWM2H3/RD4 — PWM channel 2 block 3 high output / port D pin 4 |
| Контакт 26 | PWM2L3/RD5 — PWM channel 2 block 3 low output / port D pin 5 |
| Контакт 27 | SOSCI/CN1/RC13 — Secondary oscillator input / port C pin 13 |
| Контакт 28 | SOSCO/T1CK/CN0/RA4 — Secondary oscillator output / Timer1 clock / port A pin 4 |
| Контакт 29 | VDD — Power supply |
| Контакт 30 | VSS — Ground reference |
| Контакт 31 | SDA1/RG3 — I2C data 1 / port G pin 3 |
| Контакт 32 | SCL1/RG2 — I2C clock 1 / port G pin 2 |
| Контакт 33 | RTCC/RB6/IC3 — RTCC alarm / port B pin 6 / input capture 3 |
| Контакт 34 | RB7/IC4 — Port B pin 7 / input capture 4 |
| Контакт 35 | FLT1/RB14 — PWM fault input 1 / port B pin 14 |
| Контакт 36 | FLT2/RB15 — PWM fault input 2 / port B pin 15 |
| Контакт 37 | RA14 — Port A pin 14 |
| Контакт 38 | RA15 — Port A pin 15 |
| Контакт 39 | SDA2/RG3B/U1TX — I2C data 2 / UART1 transmit (remappable) |
| Контакт 40 | SCL2/RG2B/U1RX — I2C clock 2 / UART1 receive (remappable) |
| Контакт 41 | TMS/RA6 — JTAG test mode select / port A pin 6 |
| Контакт 42 | TCK/RA7 — JTAG test clock / port A pin 7 |
| Контакт 43 | SDI1/RP20/RF2 — SPI data in 1 / remappable pin 20 / port F pin 2 |
| Контакт 44 | SDO1/RP19/RF3 — SPI data out 1 / remappable pin 19 / port F pin 3 |
| Контакт 45 | SCK1/RP18/RF6 — SPI clock 1 / remappable pin 18 / port F pin 6 |
| Контакт 46 | SS1/RP17/RF7 — SPI slave select 1 / remappable pin 17 / port F pin 7 |
| Контакт 47 | AN6/OC9/RB8 — Analog input 6 / output compare 9 / port B pin 8 |
| Контакт 48 | AN7/OC10/RB9 — Analog input 7 / output compare 10 / port B pin 9 |
| Контакт 49 | VDD — Power supply |
| Контакт 50 | VSS — Ground reference |
| Контакт 51 | AN8/RB10 — Analog input 8 / port B pin 10 |
| Контакт 52 | AN9/RB11 — Analog input 9 / port B pin 11 |
| Контакт 53 | AN10/RB12 — Analog input 10 / port B pin 12 |
| Контакт 54 | AN11/RB13 — Analog input 11 / port B pin 13 |
| Контакт 55 | AN12/OC1/RD0 — Analog input 12 / output compare 1 / port D pin 0 |
| Контакт 56 | AN13/OC2/RD1 — Analog input 13 / output compare 2 / port D pin 1 |
| Контакт 57 | AN14/OC3/RD2 — Analog input 14 / output compare 3 / port D pin 2 |
| Контакт 58 | AN15/OC4/RD3 — Analog input 15 / output compare 4 / port D pin 3 |
| Контакт 59 | VCAP/VDDCORE — Core voltage regulator capacitor connection |
| Контакт 60 | AVDD — Analog power supply |
| Контакт 61 | AVSS — Analog ground |
| Контакт 62 | TDO/RF8 — JTAG test data out / port F pin 8 |
| Контакт 63 | TDI/RF2B — JTAG test data in / port F pin |
| Контакт 64 | PGD/EMUD1/RP46 — In-circuit debug data / emulator channel 1 / remappable pin 46 |
Типичное применение
DSPIC33EP64GS506-E/PT подходит для 6 применениеs: Interleaved Power Factor Correction, DC-DC Converter Control, AC-DC Server and Telecom Power Supplies, Digital LED Driver Lighting, Solar Micro-Inverters and Power Optimizers, Industrial Motor Drives and Power Conversion.
Interleaved Power Factor Correction
The DSPIC33EP64GS506-E/PT is a natural fit for interleaved PFC because its interconnected high-speed PWM modules can drive multiple phase legs with precise phase-shift, while the 12-bit high-speed ADC samples inductor currents at the switching frequency. Microchip's own Interleaved PFC reference design for this family operates from a universal input range and produces a single high-voltage DC output of up to 350W. Current-loop bandwidths in the tens of kHz are achievable because the ADC-to-PWM interconnect removes software latency from the inner current loop, while the 16-bit DSP core runs the outer voltage loop with single-cycle MAC operations. At 60-70 MIPS the controller executes both loops plus housekeeping with margin.
Рекомендуется
DC-DC Converter Control
For digitally controlled buck, boost, half-bridge and LLC converters, the GS506 provides complementary PWM outputs with hardware dead-time insertion, fault-latching outputs, and cycle-by-cycle current limiting via on-chip comparators that feed directly into the PWM module. The 12-bit high-speed ADC with programmable gain amplifier (PGA) lets you connect low-amplitude shunt or current-transformer signals directly without an external amplifier stage. Control-loop update rates in the 100 kHz-plus range are supported by the interconnected analog fabric, and the dual-partition 64KB Flash allows firmware updates without dropping the power output. The 3.0V to 3.6V supply simplifies the controller bias rail derived from an auxiliary winding or small LDO.
Рекомендуется
AC-DC Server and Telecom Power Supplies
Server and telecom rectifiers combine PFC, LLC, telemetry and fault management, and the DSPIC33EP64GS506-E/PT handles all of these in one device: high-speed PWM for both power stages, comparator-based overcurrent protection with sub-microsecond response, and 64KB of code space sufficient for PMBus-style communication stacks. The -E grade's -40C to +125C qualification covers the hot spots near power magnetics where airflow is worst. Dual-partition Live Update is particularly valuable here, since field firmware upgrades in rack installations must not interrupt output power. The 16-bit DSP engine implements the multi-loop voltage/current/balancing control laws with single-cycle multiply-accumulate instructions.
Рекомендуется
Digital LED Driver Lighting
High-power LED drivers for industrial and outdoor lighting use constant-current control loops that benefit directly from the GS506's architecture. The interconnected PWM and comparator subsystem implements average-current-mode dimming with cycle-by-cycle current limit, while the high-speed ADC enables precise current regulation and open/short LED-string fault detection. The 64-TQFP's rich I/O count supports multi-string designs with per-string PWM dimming channels. The -40C to +125C E-grade qualification suits sealed luminaire enclosures where ambient temperatures near the driver board routinely exceed +85C. Firmware-based control also enables adaptive dimming curves and DALI-style digital dimming interfaces without additional ICs.
Рекомендуется
Solar Micro-Inverters and Power Optimizers
Micro-inverter control demands simultaneous MPPT algorithms, grid-synchronized current injection, and anti-islanding protection, all of which map well onto the DSPIC33EP64GS506's resource set. The 70 MIPS core executes MPPT perturb-and-observe or incremental-conductance algorithms with single-cycle MAC operations, while the 12-bit ADC samples panel voltage/current and grid voltage/current synchronously with the PWM carriers. On-chip comparators provide fast hardware overcurrent and overvoltage trip points required for grid interconnection safety. The dual-partition 64KB Flash supports field updates of grid-code firmware as regional regulations evolve, a real lifecycle advantage in distributed solar fleets.
Рекомендуется
Industrial Motor Drives and Power Conversion
Low-power industrial drives and solid-state power conversion benefit from the GS506's complementary PWM channels with dead-time control for three-phase inverter bridges, plus the ADC/PGA front-end for phase-current sensing via shunts. The DSP engine executes field-oriented control (FOC) math with 40-bit accumulators, keeping current-loop sample rates high even with housekeeping tasks running. The -E grade temperature range tolerates drive enclosure environments without forced cooling assumptions. Boundary-scan support simplifies production test of densely packed power boards, and the 64-pin TQFP provides enough I/O for encoder interfaces, protection inputs, and industrial communication transceivers such as CAN via available peripherals.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33EP64GS506-E/PT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33EP64GS506-I/PT | DSPIC33EP64GS506T-I/PT | DSPIC33EP64GS504-I/PT | DSPIC33EP64GS502-I/PT | DSPIC33EP32GS506-I/PT |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 64KB | 64KB | 64KB | 32KB | 16KB | 32KB |
| Max CPU Speed | 70 MIPS (60 MIPS above +85C) | 70 MIPS (-40C to +85C range) | 70 MIPS (-40C to +85C range) | 70 MIPS | 70 MIPS | 70 MIPS |
| Operating Temperature | -40C to +125C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| Digital Power Peripherals (PWM/ADC/PGA) | Interconnected high-speed PWM, 12-bit ADC with PGA, comparators | Same peripheral set | Same peripheral set | Same peripheral set | Same peripheral set | Same peripheral set |
Ключевые отличия
- Extended temperature qualification to +125C (против DSPIC33EP64GS506-I/PT)
- Dual-partition Flash with Live Update (против DSPIC33EP64GS504-I/PT)
- Interconnected digital power analog fabric (против DSPIC33EP64GP503-I/TL)
Заметки по проектированию
Decouple the 3.0V-3.6V supply with at least one 0.1uF ceramic capacitor placed within 5 mm of each VDD/VSS pair (pins 8/17, 18/29, 30/49, 50), plus a 10uF bulk capacitor near the device. The VCAP pin (pin 59) requires the exact capacitor value specified in the Microchip datasheet for the on-chip 1.8V core regulator - typically a low-ESR ceramic - and omitting it or using a wrong value is one of the most common causes of erratic reset behavior on dsPIC33EP devices. Keep AVDD (pin 60) filtered through an RC or ferrite from VDD to preserve ADC accuracy in SMPS current-sense loops.
On the 64-TQFP 10x10 mm footprint, route the interconnected PWM outputs (pins 11-16, 19-26) away from the ADC input traces (AN0-AN15 on port B) to prevent switching-noise coupling into current-sense samples. Use a solid ground plane and connect AVSS (pin 61) to it at a single quiet point near the analog section. The 0.5 mm lead pitch requires care in stencil design; a 1:1 aperture with ~100-120 um paste reduction reduces bridging risk in lead-free reflow. Follow the Microchip layout recommendations in the family datasheet PCB layout section for ground reference of analog pins.
Two frequent mistakes with this part: (1) running at 70 MIPS above +85C - the datasheet derates the device to 60 MIPS over the extended range, so verify your actual worst-case ambient and clock configuration before locking the oscillator setup; (2) assuming dual-partition Live Update exists on all GS50x devices - per the datasheet it applies to the 64-Kbyte devices only, so designs planned around Live Update must use the 64GS506 memory class. Also confirm that the -E grade you order is genuinely the extended-temperature suffix; the -I grade looks identical but is limited to +85C.
Информация о соответствии
RoHS compliant and lead-free per Microchip product page and distributor listings (matte-tin /PT TQFP package). REACH, halogen-free and conflict-minerals declarations should be confirmed from Microchip's official quality portal certificates.
