DSPIC33EP512GM710-I/PF - 70 MIPS DSC, 512KB Flash, TQFP-100 | Microchip
Артикул: DSPIC33EP512GM710-I/PF ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $17.2 | $172,00 |
| 100 | $15.85 | $1.585,00 |
| 500 | $14.4 | $7.200,00 |
| 1.000 | $12.95 | $12.950,00 |
DSPIC33EP512GM710-I/PF Обзор
A digital signal controller combines the deterministic interrupt handling and peripheral set of a microcontroller with the multiply-accumulate (MAC) DSP engine of a digital signal processor. In the power-management hierarchy, DSCs occupy the niche between general-purpose MCUs and standalone DSPs, making them the default choice for closed-loop control systems such as digital power conversion, motor control, and sensor signal processing. The dsPIC33E core executes an optimized C compiler-friendly instruction set with single-cycle MAC operations.
Key differentiating features of the GM710 include a DSP engine with 17-bit x 17-bit single-cycle MAC, dual 40-bit accumulators, and rounded saturation modes that prevent overflow artifacts in control loops. The device integrates 12-bit ADC channels operating up to approximately 1.1 Msps, motor-control PWM with dedicated fault inputs, input capture/output compare, quadrature encoder interface (QEI), CAN 2.0B, multiple UART/SPI/I2C ports, and on-chip operational amplifiers - analog blocks that directly support sensorless motor control and power-supply feedback loops without external amplifiers.
Architecturally, the device operates from a 3.0V to 3.6V single supply, includes flash self-programming, code protection, and a peripheral set reducing external component count. The on-chip op amps buffer shunt-resistor feedback for field-oriented control (FOC) of PMSM and BLDC motors, while the QEI module interfaces directly to incremental encoders for sensored servo drives. The General Purpose Plug-In Module documentation (Microchip document 50002216a) explicitly targets single/dual motor control using this device on the Explorer 16 platform.
Typical applications include single and dual motor drives, solar inverters, digital LED drivers, UPS systems, automotive body electronics, and industrial automation nodes. The wide operating voltage range and rich peripheral integration make it equally suitable for sensorless BLDC ceiling fans, servo drives, and power-factor-corrected SMPS control loops.
Design consideration: allocate VDD/VSS decoupling per datasheet recommendations on the 100-pin TQFP, and route analog op-amp inputs away from PWM switching edges to preserve ADC accuracy. The PIM (Plug-In Module) configuration for the Explorer 16 board (MA330035) provides a ready-to-use evaluation platform.
This page synthesizes distributor pricing tiers, drop-in alternatives, pin-count details, and practical design notes not consolidated in the manufacturer datasheet.
Аналоги без доработки для DSPIC33EP512GM710-I/PF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33EP512GM710-I/PF (тот же форм-фактор и посадочное место) — отличается по Package, ADC, CAN, Core Architecture, DMA Channels.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
Для этого товара нет аналогов без доработки.
Запросить аналогиDSPIC33EP512GM710-I/PF Максимальные параметры и электрические характеристики
| Core Architecture | dsPIC33E 16-bit DSC |
| CPU Performance | 70 MIPS |
| Program Memory (Flash) | 512 KB |
| Data RAM | 53 KB |
| Operating Voltage Range | 3.0 V to 3.6 V |
| Диапазон рабочих температур | -40 C to +85 C (Industrial) |
| Корпус | TQFP-100 (14x14 mm, 0.5 mm pitch) |
| ADC | 12-bit, up to ~1.1 Msps |
| DSP Engine | 17-bit x 17-bit single-cycle MAC, dual 40-bit accumulators |
| Motor Control PWM | Yes, with dedicated fault inputs |
| Quadrature Encoder Interface (QEI) | Yes |
| On-chip Operational Amplifiers | Yes |
| CAN | CAN 2.0B |
| Communication Peripherals | UART, SPI, I2C (multiple ports) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
Руководство по цоколевке DSPIC33EP512GM710-I/PF в корпусе tqfp-100 (14x14 mm, 0.5 mm pitch)
Цоколевка для DSPIC33EP512GM710-I/PF (корпус tqfp-100 (14x14 mm, 0.5 mm pitch)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для DSPIC33EP512GM710-I/PF.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
DSPIC33EP512GM710-I/PF подходит для 6 применениеs: Brushless DC Motor Control, PMSM Servo Drives, Solar Inverters and Power Conversion, Industrial Automation Nodes, Digital LED Lighting Drivers, Uninterruptible Power Supplies (UPS).
Brushless DC Motor Control
The DSPIC33EP512GM710-I/PF is well-suited for sensorless and sensored BLDC motor control. The 70 MIPS dsPIC33E core executes field-oriented control (FOC) algorithms within sub-microsecond loop times, while the integrated motor-control PWM with dedicated fault inputs provides hardware shutdown within nanoseconds of overcurrent detection. The on-chip operational amplifiers buffer shunt-resistor current signals directly to the 12-bit ADC at approximately 1.1 Msps, eliminating external amplifier components. The 512 KB flash accommodates full state-space controller code with floating-point libraries and look-up tables for sinusoidal commutation.
Рекомендуется
PMSM Servo Drives
For permanent magnet synchronous motor (PMSM) servo drives, the DSPIC33EP512GM710-I/PF provides the deterministic interrupt latency required for high-bandwidth position control loops. The quadrature encoder interface (QEI) directly interfaces to incremental encoders, while the 17-bit x 17-bit single-cycle MAC engine handles Park and Clarke transforms at the 10-20 kHz current loop rate. The dual 40-bit accumulators with rounded saturation prevent overflow artifacts during transient load steps, critical for industrial servo performance. CAN 2.0B enables multi-axis coordination in networked motion systems.
Рекомендуется
Solar Inverters and Power Conversion
The DSPIC33EP512GM710-I/PF supports digital control of solar inverters and switch-mode power supplies. The high-speed 12-bit ADC samples current and voltage feedback at rates sufficient for 100 kHz+ switching frequencies, while the DSP MAC engine executes digital PID and state-space control loops with deterministic timing. The wide 3.0V to 3.6V supply range and industrial -40C to +85C temperature rating suit outdoor photovoltaic installations. On-chip op amps condition current-sense signals, reducing bill-of-materials cost versus discrete solutions.
Рекомендуется
Industrial Automation Nodes
In industrial automation, the DSPIC33EP512GM710-I/PF serves as the central controller for sensor hubs and actuator nodes. The CAN 2.0B peripheral enables robust communication on industrial CAN networks (CANopen, DeviceNet), while multiple UART/SPI/I2C ports interface to sensors, displays, and auxiliary controllers. The 512 KB flash supports full Modbus or EtherCAT slave stack implementations, and the 53 KB RAM accommodates communication buffers without external memory expansion. Industrial -40C to +85C temperature rating ensures reliable operation in factory environments.
Рекомендуется
Digital LED Lighting Drivers
For digital LED drivers and architectural lighting systems, the DSPIC33EP512GM710-I/PF provides the computational headroom for advanced color-mixing algorithms and thermal feedback loops. The 70 MIPS performance executes multi-channel PWM dimming with 16-bit resolution at refresh rates above 200 Hz, eliminating visible flicker in video and broadcast environments. The DSP engine handles chromaticity calculations and CIE color-space conversions, while the 12-bit ADC monitors LED junction temperature via NTC thermistors for closed-loop thermal management in high-power fixtures.
Рекомендуется
Uninterruptible Power Supplies (UPS)
In UPS systems, the DSPIC33EP512GM710-I/PF manages battery charging, inverter control, and mains synchronization. The high-speed ADC samples mains voltage and current for power-quality analysis at rates matching 50/60 Hz fundamental plus harmonics, while the DSP engine implements digital PLL locking for seamless transfer between grid and battery modes. The CAN peripheral enables battery management system (BMS) communication, and the generous 512 KB flash stores inverter control firmware with grid-code compliance logic for international deployments.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33EP512GM710-I/PF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33EP512GM710-I/BG |
|---|---|---|
| Package | TQFP-100 (14x14 mm) | TFBGA-121 (10x10 mm) - different footprint |
| Brand | Microchip Technology | Microchip Technology |
| Core | dsPIC33E (16-bit DSC) | dsPIC33E (16-bit DSC) |
| Performance | 70 MIPS | 70 MIPS |
| Flash Memory | 512 KB | 512 KB |
| RAM | 53 KB | 53 KB |
| Temperature Range | -40C to +85C | -40C to +85C |
| Mounting Type | Surface Mount | Surface Mount (BGA) |
Ключевые отличия
- Hand-solderable TQFP package compatible with Explorer 16 PIM socket (против DSPIC33EP512GM710-I/BG (TFBGA-121))
- Complete 70 MIPS DSC silicon with 512 KB flash (против DSPIC33FJ64MC804-I/PT (40 MIPS, 64 KB flash))
Заметки по проектированию
The DSPIC33EP512GM710-I/PF operates from a single 3.0V to 3.6V supply; AVDD and AVSS must be properly decoupled with 0.1 uF ceramic capacitors placed as close to the pins as possible per datasheet recommendations. Estimated: at 70 MIPS full operation, core current consumption is typically 50-80 mA depending on peripheral activation; add bulk capacitance of at least 10 uF near the supply pins to handle transient loads during PWM edge transitions.
Route analog op-amp inputs and ADC input traces away from PWM switching edges and high-current motor drive traces to preserve ADC accuracy and prevent injected noise. Per Microchip design guidance for the dsPIC33EP family, maintain at least 3x trace-width spacing between analog and digital/power signals, and use a ground pour under the device with vias stitching the ground plane around the perimeter of the TQFP footprint for optimal EMI performance.
When migrating from the -I/PF (TQFP-100) to the -I/BG (TFBGA-121) variant, verify that your PCB layout accommodates the BGA footprint - these packages are NOT pin-compatible and require different land patterns. Per Microchip product documentation, the silicon die is identical, but assembly process differs (BGA requires X-ray inspection). The Explorer 16 development board PIM socket (MA330035) accepts only the TQFP-100 variant.
Estimated: at maximum 70 MIPS operation with all peripherals active, the TQFP-100 package dissipates approximately 0.3-0.5 W depending on peripheral loading. The 100-pin TQFP thermal resistance is approximately 35-40 C/W on a standard 4-layer JEDEC test board, yielding junction temperature rise of 15-20 C above ambient at full load - typically adequate without explicit heatsinking for industrial environments with adequate airflow.
Информация о соответствии
RoHS compliant per Microchip product page. The -I/PF industrial temperature grade covers -40C to +85C; this part is not AEC-Q100 qualified for automotive applications. Choose the AEC-Q100 qualified variant for automotive body electronics deployments.
