DSPIC33FJ12MC201-I/SO - 16-bit Motor Control DSC, 40 MIPS | Microchip
Артикул: DSPIC33FJ12MC201-I/SO ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.2 | $4,20 |
| 10 | $3.78 | $37,80 |
| 100 | $3.36 | $336,00 |
| 500 | $2.99 | $1.495,00 |
| 1.000 | $2.65 | $2.650,00 |
DSPIC33FJ12MC201-I/SO Обзор
A Digital Signal Controller (DSC) is a specialized microcontroller that combines a general-purpose 16-bit MCU core with hardware-level DSP capability (single-cycle MAC, barrel shifter, dual 40-bit accumulators) and tightly integrated analog/motor-control peripherals. In the broader taxonomy, the dsPIC33F family sits between 8/16-bit PIC microcontrollers and full DSP processors; it belongs to the power management > motor control IC family and is widely used as a cost-effective bridge between fixed-point DSP and standard MCU solutions.
Key specifications include up to 21 I/O pins, six PWM channels with complementary or independent outputs, a 10-bit ADC with up to 500 ksps conversion rate, and 3.0 V to 3.6 V single-supply operation. The 16-bit DSC core performs single-cycle multiply-and-accumulate operations, while dual 40-bit accumulators enable fractional arithmetic and fast Park/Clarke transforms required for sensorless vector control. Hardware fault timers and dead-time control are integrated into the PWM module, simplifying UL/IEC 60730 safety-certified drive design.
Typical applications include ceiling fan and pump variable-frequency drives, low-voltage BLDC motor controllers for appliances, hobby drones and RC ESCs, sensorless PMSM controllers for e-mobility auxiliaries, and small industrial servo drives. The wide operating voltage and robust motor-control PWM make it a strong fit for 12 V / 24 V / 48 V brushless platforms requiring deterministic real-time control.
When designing with this part, allocate sufficient decoupling (100 nF ceramic plus 4.7 uF bulk) close to VDD/AVDD pairs, and keep the analog ground and digital ground returns separated until they join at the exposed pad or a single-point ground. Use Microchip's MPLAB X IDE with the XC16 compiler and the dsPICE FOC or Motor Control Library to accelerate algorithm development.
Аналоги без доработки для DSPIC33FJ12MC201-I/SO — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33FJ12MC201-I/SO (тот же форм-фактор и посадочное место) — отличается по Core Architecture, Operating Temperature, Package, ADC, I/O Pins.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33FJ12MC201-E/SO
✅ Прямая замена✓ В наличии
$2.95 / шт.
Открыть даташит →DSPIC33FJ12MC202-I/SO
✅ Прямая замена✓ В наличии
$3.85 / шт.
Открыть даташит →DSPIC33FJ12MC202-E/SO
✅ Прямая замена✓ В наличии
$3.21 / шт.
Открыть даташит →DSPIC33FJ12GP201-E/SO
✅ Прямая замена✓ В наличии
$2.18 / шт.
Открыть даташит →DSPIC33FJ12MC201-I/SO Максимальные параметры и электрические характеристики
| Core Architecture | 16-bit dsPIC33F DSC (modified Harvard) |
| Instruction Set | 16-bit MCU + DSP extensions (single-cycle MAC) |
| Maximum CPU Speed | 40 MIPS (40 MHz, 2:1 FRC/PLL ratio) |
| Program Flash Memory | 12 KB |
| Data RAM | 1 KB |
| I/O Pins | Up to 21 |
| PWM Channels | 6 outputs (3 complementary pairs) |
| ADC | 10-bit, up to 500 ksps, up to 8 channels |
| Timers | Five 16-bit timer/counters |
| Supply Voltage (VDD) | 3.0 V to 3.6 V |
| Рабочая температура | -40C to +85C (industrial, "-I") |
| Корпус | 20-pin SOIC (0.300-inch / 7.5 mil pitch) |
| Тип монтажа | Surface Mount |
| Motor Control Peripherals | Motor Control PWM, Quadrature Encoder Interface (QEI) |
| Communication | UART, SPI, I2C |
| Статус RoHS | Compliant |
Конфигурация выводов DSPIC33FJ12MC201-I/SO
| Контакт 1 | MCLR — Master Clear (reset) input, active-low |
| Контакт 2 | AN0/VREF+/PWM1H — Analog input 0 / positive Vref / PWM1 high output |
| Контакт 3 | AN1/VREF-/PWM1L — Analog input 1 / negative Vref / PWM1 low output |
| Контакт 4 | AN2/PWM2H — Analog input 2 / PWM2 high output |
| Контакт 5 | AN3/PWM2L — Analog input 3 / PWM2 low output |
| Контакт 6 | AN4/PWM3H — Analog input 4 / PWM3 high output |
| Контакт 7 | AN5/PWM3L — Analog input 5 / PWM3 low output |
| Контакт 8 | VSS — Digital ground |
| Контакт 9 | OSC1/RC0 — Crystal input / GPIO RC0 |
| Контакт 10 | OSC2/RC1 — Crystal output / GPIO RC1 |
| Контакт 11 | RC2 — GPIO / PWM fault input |
| Контакт 12 | AVSS — Analog ground |
| Контакт 13 | AVDD — Analog supply (3.0-3.6 V) |
| Контакт 14 | RB0 — GPIO / QEI input |
| Контакт 15 | RB1 — GPIO / QEI index |
| Контакт 16 | RB2 — GPIO |
| Контакт 17 | RB3 — GPIO |
| Контакт 18 | RB4 — GPIO |
| Контакт 19 | VDD — Digital supply (3.0-3.6 V) |
| Контакт 20 | RB5 — GPIO |
Типичное применение
DSPIC33FJ12MC201-I/SO подходит для 7 применениеs: BLDC Ceiling Fan Controller, Sensorless PMSM Pump Drive, Cordless Power Tool ESC, Hobby Drone Electronic Speed Controller (ESC), Home Appliance Variable-Frequency Drive, Automotive Auxiliary Motor Controller, Industrial Servo / Robotics Drive.
BLDC Ceiling Fan Controller
The DSPIC33FJ12MC201-I/SO is purpose-built for low-voltage BLDC ceiling-fan controllers, where its 6-channel motor-control PWM with hardware dead-time and 40 MIPS DSP throughput drive silent sinusoidal commutation at 3.3 V. Designers can run sensorless back-EMF trapezoidal or basic FOC loops from 12 KB Flash, while 1 KB RAM holds one electrical cycle of sine/cosine lookup tables. The 3.0-3.6 V supply works directly from a buck-derived 3.3 V rail; the industrial temperature grade supports ceiling-fixture environments.
Рекомендуется
Sensorless PMSM Pump Drive
In small 24 V sensorless PMSM pumps (e.g., dishwasher circulation or HVAC condensate pumps), the DSPIC33FJ12MC201-I/SO executes Park/Clarke transforms and an FOC current loop at 40 MIPS with deterministic PWM timing. Its 6 PWM outputs drive a 3-phase inverter through gate drivers, and the integrated QEI interfaces Hall or encoder feedback if present. The 10-bit ADC samples phase currents at 500 ksps, supporting up to 8 multiplexed inputs including DC-bus sensing for overcurrent protection.
Рекомендуется
Cordless Power Tool ESC
Battery-powered cordless tools benefit from the DSPIC33FJ12MC201-I/SO's wide 3.0-3.6 V supply, which rides directly off a 1S Li-ion or 2S Li-ion pack regulated to 3.3 V. Its DSP MAC executes fast torque-control loops, while the 6 PWM outputs command a 3-phase bridge for brushless spindles or driver motors at up to 40 MIPS. Industrial temperature rating supports the rugged thermal envelope of handheld tools, and Microchip's free MCLib shortens firmware development.
Рекомендуется
Hobby Drone Electronic Speed Controller (ESC)
Small multi-rotor ESC boards use the DSPIC33FJ12MC201-I/SO for fast sinusoidal commutation at high electrical RPM, exploiting the 40 MIPS DSC core and single-cycle MAC to handle sensored or sensorless commutation at >20 kHz switching. The 6 PWM channels drive a small 3-phase FET bridge for 1S-3S Li-ion packs, while the QEI peripheral can decode Hall sensors or back-EMF zero-crossing through the 10-bit ADC. 12 KB Flash is enough for an ESC firmware with throttle curve and braking.
Рекомендуется
Home Appliance Variable-Frequency Drive
Washing machines, range hoods and HVAC blowers running small induction or BLDC motors integrate the DSPIC33FJ12MC201-I/SO to provide closed-loop speed control and energy-saving variable-frequency drive algorithms. The 6 PWM outputs and 10-bit ADC form a complete motor-control front-end, while the on-chip UART/SPI/I2C interfaces the appliance MCU or Wi-Fi module (e.g., ATWINC1500) for cloud connectivity. Industrial temperature rating ensures operation in hot appliance cavities.
Рекомендуется
Automotive Auxiliary Motor Controller
Auxiliary automotive motors (HVAC blowers, water pumps, electric mirrors) use the DSPIC33FJ12MC201-I/SO for BLDC commutation when an automotive-qualified variant is acceptable for non-safety subsystems. The 6 PWM outputs drive a small 3-phase inverter, and the 10-bit ADC provides DC-bus and current sensing. Designers needing full AEC-Q100 must move to the dsPIC33EP/QMC automotive family; this industrial variant suits non-safety auxiliary boards.
Рекомендуется
Industrial Servo / Robotics Drive
Small industrial servo loops and robotics actuators rely on the DSPIC33FJ12MC201-I/SO's Quadrature Encoder Interface (QEI) and 6-channel PWM for closed-loop position control at 40 MIPS. The 10-bit ADC samples position-related analog signals at 500 ksps, while the 12 KB Flash and 1 KB RAM suffice for cascaded PID controllers and trajectory planners. The 20-pin SOIC footprint drops onto compact driver PCBs used in hobby servos and educational robotics kits.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33FJ12MC201-I/SO — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33FJ12MC201-E/SO | DSPIC33FJ12MC202-I/SO | DSPIC33FJ12MC202-E/SO | DSPIC33FJ12GP201-E/SO | DSPIC33FJ12MC201-I/SS |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SOIC-20 (0.300-inch) | SOIC-20 (0.300-inch) - same | SOIC-20 (0.300-inch) - same | SOIC-20 (0.300-inch) - same | SOIC-20 (0.300-inch) - same | SSOP-20 (different PCB footprint) |
| Program Flash | 12 KB | 12 KB | 24 KB | 24 KB | 8 KB | 12 KB |
| Data RAM | 1 KB | 1 KB | 2 KB | 2 KB | 1 KB | 1 KB |
| CPU Speed | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS |
| PWM Channels | 6 (3 complementary pairs) | 6 (same) | 6 (same) | 6 (same) | 6 (general-purpose, not motor-control optimised) | 6 (same) |
| ADC | 10-bit, 500 ksps, up to 8 ch | 10-bit, 500 ksps, 8 ch | 10-bit, 500 ksps, 8 ch | 10-bit, 500 ksps, 8 ch | 10-bit, 500 ksps, 8 ch | 10-bit, 500 ksps, 8 ch |
| Operating Temperature | -40C to +85C (industrial) | -40C to +125C (extended) | -40C to +85C (industrial) | -40C to +125C (extended) | -40C to +125C (extended) | -40C to +85C (industrial) |
Ключевые отличия
- Integrated Motor-Control PWM with hardware dead-time (против DSPIC33FJ12GP201-E/SO)
- 40 MIPS DSC core at lowest cost in the family (против DSPIC33FJ12MC202-I/SO)
- 20-pin SOIC with full 6-PWM/8-ADC motor-control front end (против DSPIC33FJ12MC201-I/SS)
Заметки по проектированию
Place 100 nF ceramic decoupling as close as possible to each VDD/AVDD pin, and add a shared 4.7 uF bulk capacitor on the 3.3 V rail near the DSC. The DSPIC33FJ12MC201-I/SO draws up to ~30 mA active and <10 uA in sleep; using a low-noise LDO such as the MCP1700 ensures the analog AVdd reference for the 10-bit ADC remains stable. Tie AVss and Vss to a single ground return with a star point to avoid ground bounce across the 6 PWM outputs.
Keep the PWM output traces short and away from the analog input traces. The 20-pin SOIC package benefits from a ground pour on the top layer under the chip and a 4-layer PCB if the inverter is co-located, since the 40 MIPS DSC can generate ~50 MHz harmonic content on supply rails. Place the crystal or external clock source within 5 mm of OSC1/OSC2 pins and surround the oscillator traces with ground to reduce radiated emissions into adjacent motor phases.
Do not assume AVDD and VDD are interchangeable; the 10-bit ADC reference derives from AVdd/AVss, so connect AVDD through a separate ferrite bead or filter and avoid digital switching currents on the AVdd plane. Never leave MCLR floating - tie it to VDD through a 10 kohm pull-up so that an in-circuit programmer (ICD) can drive it. Finally, set configuration bits for the proper oscillator mode (FRC, HS, or EC) early in your code, otherwise the part will be stuck at default FRC startup frequency.
Информация о соответствии
RoHS/REACH compliant per Microchip product page. Industrial temperature grade - not AEC-Q100 qualified; choose dsPIC33EV/QMC automotive variants for vehicle applications.
