ICL7652PE4 - Precision Chopper-Stabilized Op Amp | Texas Instruments
Артикул: ICL7652PE4 ✓ АктивенICL7652PE4 Обзор
A chopper-stabilized operational amplifier is a precision amplifier that continuously corrects its own offset error and low-frequency drift. Its internal chopping and demodulation architecture reduce offset voltage and voltage drift over time, while the signal path remains suitable for low-frequency measurement systems. In the broader electronics hierarchy, the ICL7652PE4 belongs to the operational-amplifier family and supports instrumentation-amplifier, sensor-interface, and precision-feedback applications.
The device uses advanced LinCMOS process technology and provides a chopper-stabilized architecture suited to demanding analog front ends. Important selection considerations include input common-mode range, output swing, supply voltage, input bias current, noise behavior, and stability with the external compensation capacitor used by this amplifier family. The ICL7652PE4 supports operation from a single supply or split supplies, making it useful for systems that do not generate a negative reference rail.
Typical uses include bridge and thermocouple signal conditioning, low-current sensors, pressure and strain instrumentation, precision current measurement, battery-powered monitoring, and laboratory test equipment. Its low-offset characteristics are especially valuable when the signal of interest is small relative to the input common-mode voltage. The 1.9 MHz gain-bandwidth product also allows closed-loop operation at useful bandwidths rather than limiting the design to DC-only measurements.
When laying out an ICL7652PE4 circuit, place the compensation capacitor and input and output components close to the device, maintain short feedback paths, and avoid routing high-impedance input traces next to switching nodes. Check the common-mode and output-swing limits across the complete supply range. For single-supply operation, bias the non-inverting input above ground so that the output can swing within the usable common-mode region. This page combines the manufacturer datasheet information, package details, sourcing data, application guidance, and drop-in replacement context for faster engineering evaluation.
Аналоги без доработки для ICL7652PE4 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ICL7652PE4 (тот же форм-фактор и посадочное место) — отличается по Package.
ICL7652P
✅ Прямая заменаУточнить цену
Открыть даташит →ICL7652PG4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ICL7652PA
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
ICL7652PB
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
ICL7652P-A
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
ICL7652PE4 Максимальные параметры и электрические характеристики
| Amplifier Type | Precision chopper-stabilized operational amplifier |
| Number of Circuits | 1 circuit |
| Number of Inputs | 2 inputs |
| Количество выходов | 1 output |
| Gain Bandwidth Product | 1.9 MHz |
| Slew Rate | 3.1 V/us |
| Supply Operation | Single or dual supply |
| Корпус | 8-pin PDIP, 0.300 inch pitch, 7.62 mm |
| Тип монтажа | Through-hole |
| Packaging | Tube |
| Technology | Advanced LinCMOS |
| Compensation | External capacitor |
Конфигурация выводов ICL7652PE4
| Контакт 1 | NC — Not connected |
| Контакт 2 | IN- — Inverting input |
| Контакт 3 | IN+ — Non-inverting input |
| Контакт 4 | V- — Negative supply or ground connection |
| Контакт 5 | OS — Output offset adjustment and compensation connection |
| Контакт 6 | OUT — Analog output |
| Контакт 7 | V+ — Positive supply connection |
| Контакт 8 | NC — Not connected |
Типичное применение
ICL7652PE4 подходит для 6 применениеs: Strain-Gauge Bridge Instrumentation, Thermocouple Signal Conditioning, Precision Current Measurement, Low-Level Sensor Front Ends, Battery-Powered Monitoring, Laboratory and Test Equipment.
Strain-Gauge Bridge Instrumentation
The ICL7652PE4 fits strain-gauge and resistive-bridge front ends because chopper stabilization reduces offset error and drift when the bridge output is a small fraction of its excitation voltage. Its 1.9 MHz gain-bandwidth product permits closed-loop operation over the low-frequency range normally used by static force, pressure, and displacement measurements. Place the amplifier at the bridge output and keep input traces short to minimize thermoelectric effects and leakage. The principal trade-off is the need to follow the manufacturer's compensation-network guidance and verify that the bridge excitation, common-mode voltage, and output swing remain inside the device limits.
Рекомендуется
Thermocouple Signal Conditioning
The ICL7652PE4 is appropriate for low-level thermocouple amplification where microvolt-per-degree signals require low offset and low temperature drift. Chopper stabilization minimizes the static error that can dominate a precision cold-junction-compensated measurement path, while the 1.9 MHz gain-bandwidth product is more than adequate for the slow thermal signals commonly measured. Use a guarded, clean input connection and place the cold-junction reference away from regulator and switching components. Check input bias current carefully because high-impedance thermocouple conductors can turn even modest leakage into a meaningful measurement error.
Рекомендуется
Precision Current Measurement
The ICL7652PE4 can amplify the output of a low-value shunt or current sensor when measurement accuracy is dominated by offset rather than high-frequency bandwidth. Its chopper-stabilized architecture helps maintain a stable zero-level reading, and the 1.9 MHz gain-bandwidth product supports useful closed-loop bandwidth for motor, actuator, and laboratory current measurements. Keep the shunt connections short and symmetrical to minimize parasitic resistance and thermoelectric EMFs. The design must account for input bias-current error and common-mode voltage, especially when the shunt sits near a high-voltage or high-current return path.
Рекомендуется
Low-Level Sensor Front Ends
The ICL7652PE4 is useful for resistive and active sensors whose output is small, slow, and sensitive to offset error. Chopper stabilization reduces the effect of input offset voltage and drift, while the single-supply capability simplifies compact sensor modules that cannot generate a negative supply. Bias the signal within the amplifier's common-mode range and ensure that the output does not exceed its specified swing under the full sensor-output range. Input guarding and careful PCB cleanliness are especially important for high-impedance sensors, where surface leakage and contamination can otherwise dominate the amplifier's offset performance.
Рекомендуется
Battery-Powered Monitoring
The ICL7652PE4 can support low-power battery monitoring when the measured signal is primarily DC or low frequency and offset stability is more important than wide-band noise performance. Its single-supply operation reduces system complexity, and the 1.9 MHz gain-bandwidth product allows useful closed-loop bandwidth without requiring a high-speed precision amplifier. The quiescent-current contribution must be included in the overall power budget because the complete sensor chain may otherwise dominate consumption. Use low-leakage protection components and verify the device's common-mode range at the lowest battery voltage.
Рекомендуется
Laboratory and Test Equipment
The ICL7652PE4 is appropriate for laboratory amplifiers, source-measurement fixtures, and precision measurement instruments where DC offset and drift can limit accuracy. Chopper stabilization supports stable readings over long integration periods, and the 1.9 MHz gain-bandwidth product allows closed-loop gains that cover many low- and mid-frequency test signals. Follow the recommended compensation capacitor and observe settling time when changing gains or operating points. A conventional low-noise amplifier may be preferable for wideband small-signal measurements, while the ICL7652PE4 emphasizes precision near DC.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ICL7652PE4 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ICL7652P | ICL7652PG4 | ICL7652PA | ICL7652PB | ICL7652P-A |
|---|---|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Type | Chopper (zero-drift) precision operational amplifier | Zero-drift amplifier | Chopper-stabilized precision amplifier | ICL7652 family precision amplifier | ICL7652 family precision amplifier | ICL7652 family precision amplifier |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
Ключевые отличия
- Established precision chopper-stabilized operating mode (против ICL7652P)
- Pin-compatible family simplification (против ICL7652PG4)
- Single-supply-compatible precision measurement (против ICL7652PB)
Заметки по проектированию
Place the external compensation capacitor and the bypass capacitor directly adjacent to their associated pins, and keep the feedback loop compact to minimize parasitic feedback. Route the non-inverting input as a short, guarded trace away from switching nodes and power-supply return currents. For a high-impedance sensor, use a clean board surface and consider guarding because PCB contamination can create leakage comparable to the amplifier's input bias current.
Design the single-supply input bias so the signal and output remain inside the manufacturer's common-mode and output-swing limits at every supply voltage. Check the minimum battery or bus voltage, not only the nominal value. If the sensor can produce negative voltage with a positive-only supply, either translate the signal before the amplifier or use split supplies; do not assume that rail-to-rail input behavior is available without confirming it in the datasheet.
Do not substitute a conventional precision op amp solely because its nominal offset is low. Chopper-stabilized devices can have input-bias-current, common-mode, noise-versus-frequency, and compensation characteristics that require different layout and signal-source analysis. Preserve the manufacturer compensation topology, verify settling at the intended closed-loop gain, and compare the complete offset-and-drift specification rather than using a single typical parameter.
Информация о соответствии
Compliance attributes are not stated in the manufacturer result text and must be confirmed from the current Texas Instruments product documentation before qualification.