Texas Instruments

ICL7652PE4 - Precision Chopper-Stabilized Op Amp | Texas Instruments

料号: ICL7652PE4 ✓ 量产中
Single or dual supply Vdss 8-pin PDIP, 0.300 inch pitch, 7.62 mm Package
最小起订量: 1 |

ICL7652PE4 概述

The Texas Instruments ICL7652PE4 is a precision chopper-stabilized operational amplifier designed for low-offset, low-drift signal conditioning. It is a single-amplifier device in an 8-pin PDIP package, and its key operating characteristics include a 1.9 MHz gain-bandwidth product, approximately 3.1 V/us slew rate, and single-supply operation capability. The ICL7652PE4 is intended for instrumentation, sensors, low-level analog signals, and applications where input-offset error and drift can dominate measurement accuracy.

A chopper-stabilized operational amplifier is a precision amplifier that continuously corrects its own offset error and low-frequency drift. Its internal chopping and demodulation architecture reduce offset voltage and voltage drift over time, while the signal path remains suitable for low-frequency measurement systems. In the broader electronics hierarchy, the ICL7652PE4 belongs to the operational-amplifier family and supports instrumentation-amplifier, sensor-interface, and precision-feedback applications.

The device uses advanced LinCMOS process technology and provides a chopper-stabilized architecture suited to demanding analog front ends. Important selection considerations include input common-mode range, output swing, supply voltage, input bias current, noise behavior, and stability with the external compensation capacitor used by this amplifier family. The ICL7652PE4 supports operation from a single supply or split supplies, making it useful for systems that do not generate a negative reference rail.

Typical uses include bridge and thermocouple signal conditioning, low-current sensors, pressure and strain instrumentation, precision current measurement, battery-powered monitoring, and laboratory test equipment. Its low-offset characteristics are especially valuable when the signal of interest is small relative to the input common-mode voltage. The 1.9 MHz gain-bandwidth product also allows closed-loop operation at useful bandwidths rather than limiting the design to DC-only measurements.

When laying out an ICL7652PE4 circuit, place the compensation capacitor and input and output components close to the device, maintain short feedback paths, and avoid routing high-impedance input traces next to switching nodes. Check the common-mode and output-swing limits across the complete supply range. For single-supply operation, bias the non-inverting input above ground so that the output can swing within the usable common-mode region. This page combines the manufacturer datasheet information, package details, sourcing data, application guidance, and drop-in replacement context for faster engineering evaluation.

直接替换替代料: ICL7652PE4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: ICL7652PE4 (相同外形与封装尺寸) ——差异在于 Package.

Texas Instruments
Package: 8-PDIP
对比 ICL7652PE4 →

ICL7652P

✅ 直接替换
Texas Instruments
📦 8-pin PDIP
Precision chopper-stabilized operational amplifier · 1 circuit · 5 uV · 1.9 MHz · 8-PDIP · 8 pins · Through-hole · Advanced LinCMOS

联系询价

查看数据手册 →

ICL7652PG4

✅ 直接替换
📦 8-pin PDIP
Same manufacturer, family, and 8-pin PDIP footprint; exact G4 grade electrical limits and temperature rating require datasheet confirmation.

📋 参考替代料(不在目录中)

ICL7652PA

✅ 直接替换 ⚠️ 规格未核验
📦 8-pin PDIP
Same ICL7652 family and PDIP footprint; suffix-specific grade and operating-temperature limits may differ from ICL7652PE4.

📋 参考替代料(不在目录中)

ICL7652PB

✅ 直接替换 ⚠️ 规格未核验
📦 8-pin PDIP
Same ICL7652 family and PDIP footprint; electrical grade and temperature-range differences must be checked against the design limits.

📋 参考替代料(不在目录中)

ICL7652P-A

✅ 直接替换 ⚠️ 规格未核验
📦 8-pin PDIP
Same family and 8-pin PDIP footprint; grade-specific temperature and electrical limits require comparison with ICL7652PE4.

📋 参考替代料(不在目录中)

ICL7652PE4 最大额定值与电气特性

Amplifier Type Precision chopper-stabilized operational amplifier
Number of Circuits 1 circuit
Number of Inputs 2 inputs
输出数量 1 output
Gain Bandwidth Product 1.9 MHz
Slew Rate 3.1 V/us
Supply Operation Single or dual supply
封装 8-pin PDIP, 0.300 inch pitch, 7.62 mm
安装类型 Through-hole
Packaging Tube
Technology Advanced LinCMOS
Compensation External capacitor

ICL7652PE4 引脚配置

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
引脚 1 NC — Not connected
引脚 2 IN- — Inverting input
引脚 3 IN+ — Non-inverting input
引脚 4 V- — Negative supply or ground connection
引脚 5 OS — Output offset adjustment and compensation connection
引脚 6 OUT — Analog output
引脚 7 V+ — Positive supply connection
引脚 8 NC — Not connected

典型应用

ICL7652PE4 适用于 6 应用s: Strain-Gauge Bridge Instrumentation, Thermocouple Signal Conditioning, Precision Current Measurement, Low-Level Sensor Front Ends, Battery-Powered Monitoring, Laboratory and Test Equipment.

🏭

Strain-Gauge Bridge Instrumentation

The ICL7652PE4 fits strain-gauge and resistive-bridge front ends because chopper stabilization reduces offset error and drift when the bridge output is a small fraction of its excitation voltage. Its 1.9 MHz gain-bandwidth product permits closed-loop operation over the low-frequency range normally used by static force, pressure, and displacement measurements. Place the amplifier at the bridge output and keep input traces short to minimize thermoelectric effects and leakage. The principal trade-off is the need to follow the manufacturer's compensation-network guidance and verify that the bridge excitation, common-mode voltage, and output swing remain inside the device limits.

🌡️

Thermocouple Signal Conditioning

The ICL7652PE4 is appropriate for low-level thermocouple amplification where microvolt-per-degree signals require low offset and low temperature drift. Chopper stabilization minimizes the static error that can dominate a precision cold-junction-compensated measurement path, while the 1.9 MHz gain-bandwidth product is more than adequate for the slow thermal signals commonly measured. Use a guarded, clean input connection and place the cold-junction reference away from regulator and switching components. Check input bias current carefully because high-impedance thermocouple conductors can turn even modest leakage into a meaningful measurement error.

⚡

Precision Current Measurement

The ICL7652PE4 can amplify the output of a low-value shunt or current sensor when measurement accuracy is dominated by offset rather than high-frequency bandwidth. Its chopper-stabilized architecture helps maintain a stable zero-level reading, and the 1.9 MHz gain-bandwidth product supports useful closed-loop bandwidth for motor, actuator, and laboratory current measurements. Keep the shunt connections short and symmetrical to minimize parasitic resistance and thermoelectric EMFs. The design must account for input bias-current error and common-mode voltage, especially when the shunt sits near a high-voltage or high-current return path.

🧩

Low-Level Sensor Front Ends

The ICL7652PE4 is useful for resistive and active sensors whose output is small, slow, and sensitive to offset error. Chopper stabilization reduces the effect of input offset voltage and drift, while the single-supply capability simplifies compact sensor modules that cannot generate a negative supply. Bias the signal within the amplifier's common-mode range and ensure that the output does not exceed its specified swing under the full sensor-output range. Input guarding and careful PCB cleanliness are especially important for high-impedance sensors, where surface leakage and contamination can otherwise dominate the amplifier's offset performance.

🔋

Battery-Powered Monitoring

The ICL7652PE4 can support low-power battery monitoring when the measured signal is primarily DC or low frequency and offset stability is more important than wide-band noise performance. Its single-supply operation reduces system complexity, and the 1.9 MHz gain-bandwidth product allows useful closed-loop bandwidth without requiring a high-speed precision amplifier. The quiescent-current contribution must be included in the overall power budget because the complete sensor chain may otherwise dominate consumption. Use low-leakage protection components and verify the device's common-mode range at the lowest battery voltage.

🖥️

Laboratory and Test Equipment

The ICL7652PE4 is appropriate for laboratory amplifiers, source-measurement fixtures, and precision measurement instruments where DC offset and drift can limit accuracy. Chopper stabilization supports stable readings over long integration periods, and the 1.9 MHz gain-bandwidth product allows closed-loop gains that cover many low- and mid-frequency test signals. Follow the recommended compensation capacitor and observe settling time when changing gains or operating points. A conventional low-noise amplifier may be preferable for wideband small-signal measurements, while the ICL7652PE4 emphasizes precision near DC.

What is the ICL7652PE4?
The ICL7652PE4 is a Texas Instruments single precision chopper-stabilized operational amplifier in an 8-pin PDIP package. According to the manufacturer datasheet, it uses advanced LinCMOS technology and provides a gain-bandwidth product of 1.9 MHz with a slew rate of approximately 3.1 V/us. Its chopper stabilization is intended to reduce input offset error and drift in precision low-level signal-conditioning circuits.
Where can I download the ICL7652PE4 datasheet PDF?
The official ICL7652 datasheet is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/icl7652.pdf. The document contains the electrical characteristics, pin configuration, compensation guidance, typical performance curves, and application information for the ICL7652 family. Use the ICL7652PE4 ordering information and package details to confirm that the electrical grade and PDIP package match the target assembly.
What is the ICL7652PE4 pinout?
The ICL7652PE4 uses an 8-pin PDIP arrangement with pins 1 and 8 marked NC, pin 2 as IN-, pin 3 as IN+, pin 4 as V-, pin 5 as OS, pin 6 as OUT, and pin 7 as V+. The manufacturer datasheet is the controlling reference for PCB routing, and the OS pin is used for compensation according to the recommended circuit. Always verify the package drawing before assigning a footprint.
What is the gain-bandwidth product of ICL7652PE4?
The ICL7652PE4 has a gain-bandwidth product of 1.9 MHz. According to the Texas Instruments ICL7652 datasheet, this bandwidth supports closed-loop gain configurations beyond pure DC operation. The usable signal bandwidth still depends on the selected compensation capacitor, closed-loop gain, load, output amplitude, and stability network, so the 1.9 MHz figure should not be treated as the bandwidth of every feedback configuration.
Can the ICL7652PE4 operate from a single supply?
Yes, the ICL7652PE4 is designed for single-supply operation as well as split-supply operation. In a single-supply circuit, the signal must be biased into the amplifier's usable common-mode region, and the output must remain inside the specified output-swing limits. The manufacturer datasheet should be used to select the midpoint bias and confirm the exact voltage range for the chosen supply.
Is ICL7652PE4 suitable for low-level sensor measurement?
The ICL7652PE4 is suitable for low-level sensor measurement because its chopper-stabilized architecture targets low offset error and low drift. It can be used with resistive bridges, strain gauges, thermocouples, and current-sense signals when the common-mode voltage, supply range, and output swing remain within the datasheet limits. Input bias current and bias-current return error are especially important for high-impedance sources.
What is the slew rate of ICL7652PE4?
The ICL7652PE4 has a slew rate of approximately 3.1 V/us. According to the Texas Instruments ICL7652 datasheet, this rate limits how quickly the output can follow a large voltage change. For sine-wave operation, the maximum practical output frequency also depends on required amplitude and slew rate, so full-scale outputs at high frequency should be checked against the manufacturer performance curves.
What is the best drop-in replacement for ICL7652PE4?
The closest drop-in choices are ICL7652-family Texas Instruments devices that use the same 8-pin PDIP footprint and retain the chopper-stabilized electrical function, including ICL7652P and ICL7652PG4. The FindIC comparison identifies ICL7652P as an electrically similar PDIP alternative, but engineers should confirm offset, drift, compensation, common-mode, supply, and temperature requirements before approving a replacement.
What can replace ICL7652PE4?
ICL7652P is a direct functional candidate for replacing ICL7652PE4 because it is also a Texas Instruments zero-drift amplifier in an 8-pin PDIP package. ICL7652PG4 is another same-family option listed in a direct comparison. Because offset, drift, input bias current, bandwidth, and compensation requirements can differ among order codes, verify the complete manufacturer datasheet and perform a circuit-level substitution review.
Is ICL7652P the same as ICL7652PE4?
The ICL7652P and ICL7652PE4 are related Texas Instruments ICL7652 devices in the same 8-pin PDIP family, but they are not automatically identical in every grade-specific parameter. FindIC describes the ICL7652P as functionally consistent with some similar parameters while noting electrical differences. Compare input offset, drift, bias current, supply range, common-mode range, and compensation requirements for the exact production order code.
ICL7652PE4 vs ICL7652P: which is better for a bridge sensor?
Choose the ICL7652PE4 when it is the qualified baseline for the bridge-sensor design, including its temperature grade and electrical limits; otherwise ICL7652P can serve as a same-footprint candidate because both are 8-pin PDIP chopper-stabilized amplifiers. The better choice depends on offset and drift limits, input bias current versus sensor impedance, common-mode range, supply voltage, and whether the exact ICL7652P suffix meets the required production grade.
When should I choose ICL7652PE4 over another precision op amp?
Choose the ICL7652PE4 when the design must minimize offset error and drift in a low-frequency measurement while retaining the established 8-pin PDIP footprint and approximately 1.9 MHz gain-bandwidth product. A conventional precision amplifier may offer lower noise at some frequencies, while a wider-band rail-to-rail amplifier may be preferable for faster signals. The choice should follow the sensor bandwidth, common-mode range, supply, and required stability network.
Is ICL7652PE4 suitable for industrial instrumentation?
The ICL7652PE4 is suitable for many industrial instrumentation functions when its specified temperature, supply, common-mode, output-swing, and stability requirements are met. Chopper stabilization supports accurate DC and low-frequency measurement of slow sensor signals. Industrial suitability also depends on the exact electrical grade and applicable regulatory requirements, which should be confirmed from the manufacturer ordering information rather than inferred from the package.
How should ICL7652PE4 be decoupled and laid out?
Place the required bypass capacitor and the external compensation capacitor close to their associated ICL7652PE4 pins, and keep output feedback routing short to reduce parasitic feedback. Route the non-inverting input away from clocks, switching converters, and high-current return paths. For a high-impedance sensor, guard the input node and keep PCB leakage paths short because contamination and moisture can create errors comparable to the input offset.
Where can I buy ICL7652PE4 and what are the lead time and price?
Use the Request a Quote form on this page to request current unit pricing, stock allocation, minimum order quantity, and lead time for ICL7652PE4. Quote requests allow the exact PDIP ordering code and tube packaging requirement to be checked against current procurement conditions. The structured price fields on this page should be used for the current commercial offer rather than static price information in an answer.

工程参考数据: ICL7652PE4 ——对比、设计指导和合规信息。

选型指南

Choose the ICL7652PE4 when the design needs a single-amplifier, 8-pin PDIP chopper-stabilized op amp for low-level DC or low-frequency measurement, particularly when offset error and drift are more important than wideband noise performance. ICL7652P and ICL7652PG4 are the primary same-footprint candidates because web comparison information identifies them as functionally similar devices in the same PDIP family. ICL7652PA, ICL7652PB, and ICL7652P-A can support family-level substitutions when their exact grade ratings match the design. Before replacing the part, compare supply range, common-mode range, output swing, input bias current, offset, drift, temperature grade, and compensation requirements. Do not select a conventional precision amplifier when the design depends on the chopper-stabilized characteristics or the manufacturer-specific stability network.

与替代料对比

参数 本产品 ICL7652P ICL7652PG4 ICL7652PA ICL7652PB ICL7652P-A
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Amplifier Type Chopper (zero-drift) precision operational amplifier Zero-drift amplifier Chopper-stabilized precision amplifier ICL7652 family precision amplifier ICL7652 family precision amplifier ICL7652 family precision amplifier
Number of Circuits 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit

关键差异点

  • Established precision chopper-stabilized operating mode (对比 ICL7652P)
  • Pin-compatible family simplification (对比 ICL7652PG4)
  • Single-supply-compatible precision measurement (对比 ICL7652PB)

设计说明

Place the external compensation capacitor and the bypass capacitor directly adjacent to their associated pins, and keep the feedback loop compact to minimize parasitic feedback. Route the non-inverting input as a short, guarded trace away from switching nodes and power-supply return currents. For a high-impedance sensor, use a clean board surface and consider guarding because PCB contamination can create leakage comparable to the amplifier's input bias current.

Design the single-supply input bias so the signal and output remain inside the manufacturer's common-mode and output-swing limits at every supply voltage. Check the minimum battery or bus voltage, not only the nominal value. If the sensor can produce negative voltage with a positive-only supply, either translate the signal before the amplifier or use split supplies; do not assume that rail-to-rail input behavior is available without confirming it in the datasheet.

Do not substitute a conventional precision op amp solely because its nominal offset is low. Chopper-stabilized devices can have input-bias-current, common-mode, noise-versus-frequency, and compensation characteristics that require different layout and signal-source analysis. Preserve the manufacturer compensation topology, verify settling at the intended closed-loop gain, and compare the complete offset-and-drift specification rather than using a single typical parameter.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

Compliance attributes are not stated in the manufacturer result text and must be confirmed from the current Texas Instruments product documentation before qualification.

数据核验日期: 2026-11-20 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

ICL7652PE4 datasheet ICL7652PE4 pinout ICL7652PE4 datasheet pdf ICL7652PE4 equivalent ICL7652PE4 replacement ICL7652PE4 drop-in replacement ICL7652PE4 cross reference ICL7652PE4 vs ICL7652P ICL7652PE4 8-DIP pinout ICL7652PE4 precision amplifier ICL7652PE4 application circuit Texas Instruments ICL7652PE4

相关元器件 & 术语

Texas Instruments ICL7652PE4 ICL7652P ICL7652PG4 ICL7652PA ICL7652PB ICL7652P-A operational amplifier precision amplifier chopper-stabilized amplifier zero-drift amplifier instrumentation amplifier signal conditioning input offset voltage input bias current common-mode voltage gain-bandwidth product slew rate advanced LinCMOS 8-pin PDIP DIP package single-supply operation external compensation capacitor strain-gauge bridge thermocouple
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情