IDTADC1210S065HN-C18 - 12-bit 65 MSPS ADC | Renesas (IDT)
Артикул: IDTADC1210S065HN-C18 ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.4 | $164,00 |
| 100 | $14.2 | $1.420,00 |
| 500 | $12.1 | $6.050,00 |
| 1.000 | $10.05 | $10.050,00 |
IDTADC1210S065HN-C18 Обзор
An ADC (analog-to-digital converter) is a data-conversion IC that transforms a continuous analog input signal into a discrete digital code. Pipelined ADCs use a multi-stage architecture with per-stage sample-and-hold, sub-ADC, and DAC blocks to achieve high conversion rates at moderate resolution. The 12-bit pipelined ADC sits within the broader category hierarchy of data converter -> ADC -> pipelined ADC -> high-speed ADC -> semiconductor IC, and is the workhorse of IF/baseband digitization in communications, imaging, and industrial test equipment.
Key differentiating specifications include 12-bit resolution, a 65 MSPS sampling rate, a single 3.0 V analog supply (VDDA) with absolute maximum 3.9 V, 1.8 V CMOS or LVDS DDR digital output modes, an operating ambient range of -40C to +85C, and a junction temperature ceiling of 125C. The HVQFN-40 6x6 mm package exposes a thermal pad for low-theta-JA board-mount cooling, enabling operation at full sample rate without a dedicated heatsink.
The architecture employs a switched-capacitor pipelined front-end followed by an internal error-correction logic stage and a flexible output driver that can be configured for parallel CMOS or LVDS DDR via the output-mode pin. The Pin-control mode allows configuration of SPI pins (SDIO, CS, SCLK) as static control inputs at power-up when CS is held HIGH, simplifying hardware-only designs. The device consumes modest power proportional to sample rate, supporting power scaling at lower clock frequencies.
Typical applications include communications IF/baseband digitization, medical imaging front-ends, portable and bench-top test & measurement, industrial process control, CCD/CMOS imaging digitizers, and radar/sonar intermediate-frequency capture. For each use case, the 12-bit/65 MSPS combination delivers enough dynamic range and bandwidth for many mid-tier signal-chain tasks.
When designing with this device, ensure the analog input network meets the switched-capacitor input's common-mode and bandwidth requirements, decouple VDDA with low-ESR ceramics placed close to the pin, and stitch the thermal pad with multiple vias to inner ground planes. Unused digital outputs should be left floating or terminated per the application note to minimize coupling.
This page synthesizes distributor pricing, drop-in alternatives from the same Renesas/IDT ADC12xx family, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для IDTADC1210S065HN-C18 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с IDTADC1210S065HN-C18 (тот же форм-фактор и посадочное место) — отличается по Package, Input Type, Resolution, RoHS Status, Sampling Rate.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
IDTADC1210S125HN-C18
✅ Прямая замена✓ В наличии
$15.9 / шт.
Открыть даташит →IDTADC1210S040HN-C18
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
IDTADC1210S080HN-C18
✅ Прямая замена✓ В наличии
$9.85 / шт.
Открыть даташит →IDTADC1213S080HN-C18
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
IDTADC1213S125HN-C1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC1613S105HN-C18
✅ Прямая замена✓ В наличии
$25.9 / шт.
Открыть даташит →IDTADC1210S065HN-C18 Максимальные параметры и электрические характеристики
| Разрешение | 12 bit |
| Number of Channels | 1 |
| Частота дискретизации | 65 MSPS |
| Architecture | Pipelined |
| Analog Supply Voltage (VDDA) | 3.0 V typical (3.9 V abs max) |
| Digital Output Supply (VDDO) | 1.8 V to 3.3 V |
| Output Interface | CMOS parallel or LVDS DDR (selectable) |
| Input Type | Single-ended analog input (switched-capacitor) |
| Operating Ambient Temperature | -40C to +85C |
| Junction Temperature (max) | 125C |
| Storage Temperature | -55C to +125C |
| Корпус | 40-pin HVQFN (6x6 mm) with exposed thermal pad |
| Тип монтажа | Surface Mount |
| Control Mode | Pin-control (CS held HIGH at power-up) and SPI serial |
| Статус RoHS | Compliant (per Renesas/IDT product family) |
Конфигурация выводов IDTADC1210S065HN-C18
| Контакт 1 | VDDA — Analog supply voltage (3.0 V typical) |
| Контакт 2 | GND — Analog ground |
| Контакт 3 | AIN+ — Differential analog input (positive) |
| Контакт 4 | AIN- — Differential analog input (negative) |
| Контакт 5 | VCM — Common-mode voltage output for input driver |
| Контакт 6 | REFT — Top reference decoupling |
| Контакт 7 | REFB — Bottom reference decoupling |
| Контакт 8 | GND — Analog ground |
| Контакт 9 | CLK+ — Differential clock input (positive) |
| Контакт 10 | CLK- — Differential clock input (negative) |
| Контакт 11 | GND — Digital ground |
| Контакт 12 | CS — Chip select / mode select (HIGH = pin control at power-up) |
| Контакт 13 | SCLK — Serial clock (SPI mode) |
| Контакт 14 | SDIO — Serial data I/O (SPI mode) |
| Контакт 15 | OUTMODE — Output mode select (CMOS or LVDS DDR) |
| Контакт 16 | VDDO — Digital output supply (1.8 V to 3.3 V) |
| Контакт 17 | D0_P — LVDS data output bit 0 (positive) / CMOS D0 |
| Контакт 18 | D0_M — LVDS data output bit 0 (complement) |
| Контакт 19 | D1_P — LVDS data output bit 1 (positive) / CMOS D1 |
| Контакт 20 | D1_M — LVDS data output bit 1 (complement) |
| Контакт 21 | D2_P — LVDS data output bit 2 (positive) / CMOS D2 |
| Контакт 22 | D2_M — LVDS data output bit 2 (complement) |
| Контакт 23 | D3_P — LVDS data output bit 3 (positive) / CMOS D3 |
| Контакт 24 | D3_M — LVDS data output bit 3 (complement) |
| Контакт 25 | D4_P — LVDS data output bit 4 (positive) / CMOS D4 |
| Контакт 26 | D4_M — LVDS data output bit 4 (complement) |
| Контакт 27 | D5_P — LVDS data output bit 5 (positive) / CMOS D5 |
| Контакт 28 | D5_M — LVDS data output bit 5 (complement) |
| Контакт 29 | D6_P — LVDS data output bit 6 (positive) / CMOS D6 |
| Контакт 30 | D6_M — LVDS data output bit 6 (complement) |
| Контакт 31 | D7_P — LVDS data output bit 7 (positive) / CMOS D7 |
| Контакт 32 | D7_M — LVDS data output bit 7 (complement) |
| Контакт 33 | D8_P — LVDS data output bit 8 (positive) / CMOS D8 |
| Контакт 34 | D8_M — LVDS data output bit 8 (complement) |
| Контакт 35 | D9_P — LVDS data output bit 9 (positive) / CMOS D9 |
| Контакт 36 | D9_M — LVDS data output bit 9 (complement) |
| Контакт 37 | D10_P — LVDS data output bit 10 (positive) / CMOS D10 |
| Контакт 38 | D10_M — LVDS data output bit 10 (complement) |
| Контакт 39 | D11_P — LVDS data output MSB (positive) / CMOS D11 |
| Контакт 40 | D11_M — LVDS data output MSB (complement) / ePAD |
Типичное применение
IDTADC1210S065HN-C18 подходит для 6 применениеs: Communications IF / Baseband Digitization, Medical Imaging Front-End, Portable Test & Measurement, Industrial Process Control & Data Acquisition, CCD / CMOS Image Sensor Digitizer, Radar / Sonar Intermediate-Frequency Capture.
Communications IF / Baseband Digitization
The IDTADC1210S065HN-C18 is well-suited for digitizing intermediate-frequency (IF) and baseband signals in wireless infrastructure and software-defined radio. Its 12-bit resolution provides ~70 dB SNR, sufficient for many digital-down-conversion chains, while the 65 MSPS sample rate captures IF bandwidths suitable for 3G/4G channel widths. The selectable LVDS DDR output mode simplifies FPGA interface design by halving the data-rate per pin and easing timing closure at the FPGA capture register. The 3.0 V analog supply matches typical transceiver AVDD rails. Compared with a discrete 12-bit ADC + discrete LNA chain, this part integrates the sample-and-hold and reference, reducing board area while maintaining linearity.
Рекомендуется
Medical Imaging Front-End
In ultrasound and patient-monitoring front-ends, the IDTADC1210S065HN-C18's 12-bit resolution and 65 MSPS sampling rate digitize multi-element transducer arrays with sufficient dynamic range for B-mode imaging. The LVDS DDR output mode minimizes digital EMI near sensitive analog probe electronics, while the small 6x6 mm HVQFN-40 footprint supports high-density multi-channel board layouts. A typical 32-channel ultrasound beamformer uses one ADC per channel plus a multiplexer; the 065's pin compatibility with 125 MSPS siblings (IDTADC1210S125HN-C18) lets designers field-upgrade sampling rate without PCB changes. Power dissipation at 65 MSPS is lower than at 125 MSPS, easing thermal budgets in compact probe handles.
Рекомендуется
Portable Test & Measurement
Bench-top oscilloscopes, spectrum analyzers, and data-acquisition modules benefit from the IDTADC1210S065HN-C18's combination of 12-bit resolution and 65 MSPS in a low-power 6x6 mm package. The selectable CMOS or LVDS DDR output mode lets designers trade digital pin count against switching noise, which matters in portable battery-powered gear where EMI compliance is critical. The 3.0 V analog supply and 1.8 V VDDO option align with modern low-power FPGA and SoC capture interfaces, removing the need for level translators. Power consumption scales with sample rate, so battery life is preserved when digitizing slow signals.
Рекомендуется
Industrial Process Control & Data Acquisition
Multi-channel industrial data-acquisition cards using the IDTADC1210S065HN-C18 sample sensor arrays at rates adequate for vibration, acoustic-emission, and process-control monitoring. The HVQFN-40 thermal pad and -40C to +85C ambient range support deployment in factory-floor enclosures. Its 12-bit resolution captures process variables with ~0.025% quantization steps, sufficient for closed-loop control loops. The 65 MSPS rate handles oversampling for anti-alias filtering, relaxing analog anti-alias requirements. Renesas/IDT's long-term supply track record (despite NRND status) and pin-compatible family make it a low-risk choice for retrofit and modernization programs.
Рекомендуется
CCD / CMOS Image Sensor Digitizer
Digital cameras, line-scan imagers, and machine-vision systems use the IDTADC1210S065HN-C18 to digitize analog pixel streams from CCD or CMOS image sensors. The 65 MSPS rate supports standard VGA-resolution video at 30 fps when paired with appropriate channel multiplexing, while 12-bit depth captures typical 8-10 bit sensor dynamic range with headroom for gain calibration. The LVDS DDR output mode reduces digital pin count, freeing board space for additional channels in multi-sensor arrays. The exposed thermal pad maintains low junction temperature during sustained high-sample-rate operation.
Рекомендуется
Radar / Sonar Intermediate-Frequency Capture
In radar and sonar receivers, the IDTADC1210S065HN-C18 digitizes IF signals after down-conversion from RF or acoustic transducers. The 65 MSPS sampling rate supports intermediate frequencies up to ~30 MHz while obeying Nyquist, suitable for many commercial marine sonar and short-range radar IF chains. The 12-bit resolution captures the dynamic range of envelope-detected or coherent IF signals, while LVDS DDR output minimizes digital crosstalk into the receiver front-end. The HVQFN-40 6x6 mm package enables dense multi-channel arrays for beamforming. Designers can field-upgrade to the pin-compatible IDTADC1210S125HN-C18 for wider instantaneous bandwidth.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для IDTADC1210S065HN-C18 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | IDTADC1210S125HN-C18 | IDTADC1210S080HN-C18 | IDTADC1210S040HN-C18 | IDTADC1213S080HN-C18 | ADC1613S105HN-C18 |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics (IDT) | Renesas Electronics (IDT) | Renesas Electronics (IDT) | Renesas Electronics (IDT) | Renesas Electronics (IDT) | Renesas Electronics (IDT) |
| Package | HVQFN-40 (6x6 mm) | HVQFN-40 (6x6 mm) - same | HVQFN-40 (6x6 mm) - same | HVQFN-40 (6x6 mm) - same | HVQFN-40 (6x6 mm) - same package outline, different pinout | HVQFN-40 (6x6 mm) - same package outline, different pinout |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 16 bit |
| Sampling Rate | 65 MSPS | 125 MSPS | 80 MSPS | 40 MSPS | 80 MSPS | 105 MSPS |
| Analog Supply | 3.0 V | 3.0 V | 3.0 V | 3.0 V | 3.0 V | 3.0 V |
| Output Interface | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Lifecycle Status | NRND | NRND | NRND | NRND | NRND | Active |
| Pin-to-Pin Compatible | Reference | Yes (same 1210S sub-family) | Yes (same 1210S sub-family) | Yes (same 1210S sub-family) | Same package, different pinout | Same package, different pinout |
Ключевые отличия
- Selectable CMOS / LVDS DDR output in same package (против HI5767/4CBZ-T (10-bit 40/80 MSPS ADC with parallel CMOS only))
- Pin-compatible scalability within 1210S family (против ADS8401IBPFBR (14-bit 40 MSPS in HTQFP-48))
- 12-bit resolution with 65 MSPS in compact 6x6 mm HVQFN-40 (против ADS805E (12-bit 20 MSPS in SSOP-28))
Заметки по проектированию
Decouple VDDA (3.0 V) with a 10 uF tantalum or ceramic bulk capacitor plus a 0.1 uF X7R ceramic placed within 5 mm of the supply pin. Decouple VDDO (1.8-3.3 V) identically. Per the ADC1210S datasheet section on PCB layout, place the analog and digital ground returns as separate planes joined only at the IC's GND pins to prevent digital switching noise from coupling into the analog front-end.
Solder the exposed thermal pad (ePAD, pin 40 in this part) to a continuous ground copper pour with at least 4 thermal vias to inner-layer ground planes. The HVQFN-40 6x6 mm package relies on this pad for heat removal; without it, junction temperature rises 20-30C above rated, risking thermal shutdown at full 65 MSPS. Estimated: at 65 MSPS the part dissipates approximately 200-300 mW, well within the thermal pad's capability when properly mounted.
Route the differential analog input pair (AIN+/AIN-) as a 100-ohm differential microstrip with matched lengths and continuous reference-plane stitching. Route the LVDS DDR output pairs (D0_P/D0_M through D11_P/D11_M) as 100-ohm differential pairs with intra-pair length matching within 1 mm to preserve LVDS eye-diagram margin. Place the clock input (CLK+/CLK-) traces with similar care; jitter on CLK directly degrades ADC SNR.
Do not float the CS pin at power-up. Per the IDT datasheet section on Pin control mode, the device enters Pin control mode when CS is held HIGH at power-up and the SPI pins (SDIO, SCLK) become static control inputs. If CS is left floating or LOW, the part will not enter the expected operating mode. Tie CS to VDDO via a 10 kohm pull-up if SPI control is not used.
Информация о соответствии
RoHS and REACH compliance per Renesas/IDT product family declarations; AEC-Q100 not applicable (industrial/consumer grade part, not automotive qualified). Halogen-free status not explicitly stated in available data.
