INA2134UAG4 - 0dB Dual Audio Receiver | Texas Instruments
Артикул: INA2134UAG4 ✓ АктивенINA2134UAG4 Обзор
An audio differential line receiver is an interface circuit that converts two correlated input voltages into a single-ended output. It belongs to the amplifier-IC hierarchy and combines low-noise operational-amplifier behavior with integrated precision gain-setting resistors. This integration makes it especially useful in professional audio, instrumentation, and communications equipment where predictable gain, low distortion, and compact implementation are more important than user-adjustable amplification.
The INA2134 family provides excellent AC specifications for high-performance audio applications. Key features include 0 dB gain, 14 V/µs slew rate, 74 dB minimum common-mode rejection, and 0.0005% distortion at 1 kHz. Its wide output-voltage swing and strong output drive allow the receiver to operate directly into subsequent audio stages without adding another high-gain amplification stage.
Internally, the two channels use precision on-chip resistors to establish the differential-to-single-ended conversion and unity gain. This approach removes external gain-setting networks while preserving channel consistency. The 14-SOIC package provides a conventional surface-mount footprint and separates the two receiver channels for straightforward dual-audio routing.
Typical uses include balanced professional-audio inputs, stereo audio interface boards, mixing-console preamplifier stages, test and measurement equipment, and communications front ends. The dual-channel configuration is particularly useful where two balanced signals must be conditioned consistently, while the 0 dB gain preserves the source signal level for later gain-control stages.
When laying out the receiver, treat the differential inputs as a matched, impedance-sensitive pair and keep their routing symmetrical. Place decoupling capacitors close to the supply pins and route the two channels consistently to minimize conversion of common-mode interference into differential error. Confirm the output swing against the voltage headroom of the following stage.
This page combines manufacturer specifications, a same-footprint replacement assessment, and application-oriented design guidance. The accompanying comparison and selection notes make it easier to choose between the documented INA2134 order variants without overlooking package lifecycle, channel alignment, or interface constraints.
Аналоги без доработки для INA2134UAG4 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с INA2134UAG4 (тот же форм-фактор и посадочное место) — отличается по Package, RoHS Status.
INA2134UA
✅ Прямая заменаУточнить цену
Открыть даташит →INA2134UA/2K5E4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
INA2134UAG4 Максимальные параметры и электрические характеристики
| Device Type | Dual differential audio line receiver |
| Number of Channels | 2 channels |
| Voltage Gain | 1 V/V (0 dB) |
| Distortion at 1 kHz | 0.0005% |
| Slew Rate | 14 V/µs |
| Minimum Common-Mode Rejection | 74 dB |
| Common-Mode Rejection Test Resistance | 0 ohm |
| Корпус | 14-SOIC, 3.90 mm width |
| Тип монтажа | Surface mount |
| Integrated Precision Resistors | Yes, on chip |
| Output Drive | High output drive |
| Output Voltage Swing | Wide output voltage swing |
| Статус RoHS | Compliant |
Руководство по цоколевке INA2134UAG4 в корпусе 14-soic, 3.90 mm width
Цоколевка для INA2134UAG4 (корпус 14-soic, 3.90 mm width). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для INA2134UAG4.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
INA2134UAG4 подходит для 6 применениеs: Balanced Professional Audio Input, Stereo Audio Interface, Mixer Preamplifier Input, Balanced Recording Preamp, Test and Measurement Front End, Communications Signal Conditioning.
Balanced Professional Audio Input
The INA2134UAG4 is well suited to converting a balanced professional-audio input into a single-ended signal for the next processing stage. Its 0 dB gain preserves the incoming level, while the documented 74 dB minimum common-mode rejection reduces interference that appears equally on both input conductors. The 0.0005% distortion at 1 kHz and 14 V/µs slew rate support low-error, responsive handling of audio waveforms. Use the device ahead of a gain-control or line-output stage, and verify that the downstream amplifier can accept the resulting output swing.
Рекомендуется
Stereo Audio Interface
The two independent INA2134UAG4 receiver channels support stereo balanced inputs without requiring two separate receiver packages. Both channels use the fixed 1 V/V gain characteristic and integrated precision resistors, which simplifies channel matching and reduces the number of external gain-setting components. This configuration is useful in stereo preamps, monitor controllers, and balanced audio interface cards. The low 0.0005% distortion figure at 1 kHz supports clean source conversion, while the 14 V/µs slew rate provides useful transient headroom before the next gain stage.
Рекомендуется
Mixer Preamplifier Input
INA2134UAG4 can serve as the balanced input receiver ahead of a mixer preamplifier because it performs differential-to-single-ended conversion at 0 dB without adding substantial gain. The 74 dB minimum common-mode rejection helps suppress ground-potential differences and shared noise on balanced cable runs, while the 0.0005% distortion at 1 kHz limits added signal error. The 14 V/µs slew rate also helps the stage follow fast transients. Keep both input traces symmetric and confirm that the following mixer input has sufficient voltage headroom.
Рекомендуется
Balanced Recording Preamp
For a balanced recording preamplifier, the INA2134UAG4 provides the input conversion stage without changing the nominal signal gain. Its 0 dB architecture lets the designer retain control over where gain is applied, which is useful when a downstream potentiometer, low-noise amplifier, or analog-to-digital converter interface determines the overall signal path. Low distortion of 0.0005% at 1 kHz supports transparent conversion, and the two channels allow consistent left and right routing. The receiver should be followed by circuitry designed for the expected signal level and output impedance.
Рекомендуется
Test and Measurement Front End
The INA2134UAG4 is useful in instrumentation front ends that receive balanced sensor or test signals and require a referenced single-ended output. The 0 dB gain preserves the measurement amplitude, and the common-mode rejection characteristic helps isolate the wanted differential component from shared noise. Its 14 V/µs slew rate supports signals with rapid transitions, while the low distortion specification makes it appropriate for high-fidelity test paths. For precision measurements, confirm input offset, input bias current, supply range, and output swing against the complete operating requirements.
Рекомендуется
Communications Signal Conditioning
INA2134UAG4 can condition a balanced communications signal when the downstream circuitry requires a single-ended result. The receiver’s unity gain prevents premature signal amplification, while its 74 dB minimum common-mode rejection improves discrimination against noise shared by the differential pair. The low 0.0005% distortion at 1 kHz and 14 V/µs slew rate provide a useful combination of linearity and dynamic response. Keep the input routing balanced, use an appropriate source termination, and verify the supply and common-mode limits before using the receiver outside audio-focused designs.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для INA2134UAG4 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | INA2134UA | INA2134UA/2K5E4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-SOIC (0.154", 3.90mm Width) | 14-SOIC - same footprint | 14-SOIC - same footprint |
| Number of Channels | 2 channels | 2 channels | 2 channels |
| Voltage Gain | 1 V/V (0 dB) | 1 V/V (0 dB) | 1 V/V (0 dB) |
| Distortion at 1 kHz | 0.0005% | 0.0005% | 0.0005% |
| Minimum Common-Mode Rejection | 74 dB | 74 dB | 74 dB |
| Slew Rate | 14 V/µs | 14 V/µs | 14 V/µs |
Ключевые отличия
- Dual balanced-audio receiver integration (против INA134 family)
- Fixed low-noise unity-gain conversion (против INA2134UA)
- Integrated precision gain-setting resistors (против INA2134UA/2K5E4)
Заметки по проектированию
Route each differential pair as a tightly coupled, symmetric pair and keep the two input conductors over comparable ground-plane conditions. Unequal trace lengths or asymmetric impedance can allow external interference to become differential error. Place the receiver close to the connector or source when practical, and keep the output routing away from clocks, switching regulators, and other fast-edge nodes.
Confirm source impedance and termination strategy before finalizing the input network. The receiver’s integrated precision resistors establish the nominal gain, but external source resistance and cable termination still affect practical common-mode rejection and channel matching. Use identical input networks for both channels and avoid adding different series components unless the downstream signal architecture requires them.
Do not assume that a 14-SOIC footprint alone guarantees an interchangeable procurement item. Confirm the exact order code, package dimensions, pin assignment, lifecycle status, and required shipping format before replacing INA2134UAG4. The documented INA2134UA/2K5E4 comparison identifies an obsolete product status, so a footprint match alone is not sufficient for a new production design.
Информация о соответствии
RoHS compliance is identified in the INA2134UA versus INA2134UAG4 comparison. No verified statements were available for the other compliance categories.