Texas Instruments

INA217AIDWT - Low-Noise Instrumentation Amplifier | Texas Instruments

Артикул: INA217AIDWT ✓ Активен
±4.5 V to ±18 V Vdss 16-pin SOIC wide-body (DW) Package
MOQ: 1 |

INA217AIDWT Обзор

Texas Instruments INA217AIDWT is a low-noise, low-distortion monolithic instrumentation amplifier with 1.3 nV/√Hz input noise at 1 kHz, 0.004% THD+N at 1 kHz with a gain of 100, and 800 kHz bandwidth at a gain of 100. The device operates from ±4.5 V to ±18 V and is packaged in a 16-pin SOIC wide-body package. Its external-resistor gain configuration and high common-mode rejection make it suitable for precision differential-receiver front ends.

An instrumentation amplifier is a specialized amplifier that measures the voltage difference between two input signals while rejecting large common-mode voltages. The INA217 belongs to the instrumentation-amplifier hierarchy within signal-chain ICs, where low input noise, accurate gain control, and common-mode rejection are more important than general-purpose op-amp flexibility. The INA217 is also identified by Texas Instruments as a replacement for the SSM2017, with its 16-pin SOIC option providing the same package and pinout as the SSM2017.

The principal performance characteristics are 1.3 nV/√Hz noise at 1 kHz, greater than 100 dB common-mode rejection, and 800 kHz bandwidth at a gain of 100. Its total harmonic distortion plus noise remains only 0.004% at 1 kHz under that gain condition. Current-feedback circuitry supports wide bandwidth and dynamic response across a broad range of externally programmed gains, while the operating supply range accommodates precision laboratory, industrial, and instrumentation systems using dual rails.

The INA217 uses an external gain-setting resistor, allowing the closed-loop gain to be selected according to the application. This architecture makes the device appropriate for differential sensor interfaces where source impedance is known and signal gain must be adjusted. The 16-pin wide-body SOIC provides sufficient pin count for the input, output, supply, feedback, and gain-setting connections while retaining compatibility with the referenced SSM2017 footprint.

Typical uses include low-level bridge excitation and measurement, precision differential voltage acquisition, current-shunt monitoring, sensor-interface amplification, and laboratory instrumentation. In each case, the low-noise input stage preserves small differential signals, while common-mode rejection limits the effect of voltage shared by both input terminals. The wide supply range supports systems operating at rail voltages between 4.5 V and 18 V per rail.

The most important PCB consideration is to follow the manufacturer’s pin-description table and recommended decoupling layout. Input and supply connections should be short, the gain resistor should connect only to the specified gain pin, and grounding should avoid shared high-current return paths. Because the device is intended for precision signal extraction, component placement and source-impedance balancing are as important as the nominal noise specification.

This product page combines the INA217’s principal electrical characteristics, verified package information, sourcing guidance, replacement considerations, and application-focused engineering guidance. It also highlights where a drop-in replacement can preserve the PCB footprint and where original SSM2017 compatibility must be checked against the complete pin and electrical requirements.

Аналоги без доработки для INA217AIDWT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

INA217AIDWR

✅ Прямая замена
📦 16-pin SOIC wide-body (DW)
Same INA217AIDW electrical configuration and DW footprint; only the production packing format changes from tube to tape and reel, with 0% electrical-rating difference.

📋 Справочный аналог (нет в каталоге)

INA217AIDWTG4

✅ Прямая замена
📦 16-pin SOIC wide-body (DW)
Same INA217AIDW gain and 16-pin DW electrical configuration; the G4 ordering designation differs, with 0% stated difference in the core performance ratings.

📋 Справочный аналог (нет в каталоге)

INA217AIDWT Максимальные параметры и электрические характеристики

Amplifier Type 1-amplifier monolithic instrumentation amplifier
Input Noise Density 1.3 nV/√Hz at 1 kHz
Total Harmonic Distortion Plus Noise 0.004% at 1 kHz, gain = 100
Bandwidth at Gain 100 800 kHz
Overall Bandwidth 3.4 MHz
Supply Voltage Range ±4.5 V to ±18 V
Common-Mode Rejection >100 dB
Gain Configuration Set by external resistor
Slew Rate 15 V/µs
Maximum Differential Input Voltage ±250 µV
Диапазон рабочих температур -40 °C to +125 °C
Корпус 16-pin SOIC wide-body (DW)
Тип монтажа Surface mount
Number of Circuits 1
Replacement Reference SSM2017
Статус RoHS Green product, no Sb/Br

Руководство по цоколевке INA217AIDWT в корпусе 16-pin soic wide-body (dw)

Цоколевка для INA217AIDWT (корпус 16-pin soic wide-body (dw)). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.

Схема цоколевки корпуса 16-pin soic wide-body (dw) для INA217AIDWT

Нет подробных данных о распиновке для INA217AIDWT.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

INA217AIDWT подходит для 6 применениеs: Precision Bridge Sensor Amplification, Low-Level Differential Voltage Acquisition, Current-Shunt Monitoring, Laboratory Instrumentation Front End, Balanced Audio and Communications Inputs, Industrial Differential Sensor Interface.

🏭

Precision Bridge Sensor Amplification

The INA217AIDWT fits bridge-based pressure, load, and strain measurements because its 1.3 nV/√Hz input noise limits the amplifier’s contribution to the measured signal while common-mode rejection above 100 dB rejects much of the voltage shared by the two bridge inputs. The external gain resistor makes the circuit scale simple and repeatable. At a gain of 100, the device retains 800 kHz bandwidth and has 0.004% THD+N at 1 kHz, providing useful bandwidth for slow mechanical signals and higher-speed force or vibration tests. Place the amplifier close to the bridge, balance source impedances, and return its output to a quiet analog ground to prevent sensor leads and PCB leakage from overwhelming the low-level differential output.

📡

Low-Level Differential Voltage Acquisition

For small differential voltages riding on a larger common-mode potential, the INA217AIDWT combines 1.3 nV/√Hz input noise with greater than 100 dB common-mode rejection. This makes it useful for frontend conditioning before a precision ADC, particularly where the source is a balanced sensor rather than a single-ended signal. The 800 kHz bandwidth at a gain of 100 supports measurement loops that need more bandwidth than a slow precision-only amplifier provides. A practical implementation should use short, shielded or tightly routed differential traces, matched input components where appropriate, and local supply bypassing. The gain resistor must follow the manufacturer circuit, and its tolerance and temperature coefficient become part of the overall gain error when the programmed gain is high.

⚡

Current-Shunt Monitoring

The INA217AIDWT can amplify the small voltage generated across a current-sense shunt while rejecting the supply or load voltage common to both shunt terminals. Its 1.3 nV/√Hz input noise is valuable when the measured current produces only millivolts or microvolts, and common-mode rejection above 100 dB improves measurement integrity in systems with substantial bus voltage. The ±4.5 V to ±18 V supply range accommodates laboratory, industrial, and communications equipment. Keep the shunt’s Kelvin connections separate from its power terminals, place the amplifier near the shunt, and use a symmetric return path to prevent copper drops from entering the differential input. Verify the input common-mode range and differential input limits at the selected operating gain.

🔬

Laboratory Instrumentation Front End

The INA217AIDWT suits laboratory instruments that measure weak differential signals while presenting substantial common-mode voltage, such as sensor conditioners, precision source interfaces, and multichannel measurement front ends. Its current-feedback architecture supports 800 kHz bandwidth at a gain of 100, while the 0.004% THD+N specification helps preserve waveform fidelity in signal-oriented tests. The 16-pin wide-body SOIC also offers enough routing flexibility for supply, feedback, and gain components. For best performance, use a clean analog supply, decouple close to the device, avoid sharing return-current paths with display or relay circuitry, and observe the input common-mode limits. The external gain resistor should be a low-noise, tightly toleranced component when measurement accuracy dominates.

🎧

Balanced Audio and Communications Inputs

The INA217AIDWT can condition a balanced low-level audio or communications input when the design requires differential extraction and low input-referred noise. Its 1.3 nV/√Hz input noise and greater than 100 dB common-mode rejection help preserve small signal content while rejecting common-mode hum or coupled noise on the pair. The 0.004% THD+N figure at 1 kHz and gain of 100 makes it particularly relevant to high-fidelity measurement paths. The amplifier should be followed by suitable gain staging and filtering rather than treated as a general-purpose line output stage. Maintain balanced routing, keep the gain resistor close to the device, and isolate the input from digital switching paths. Check the common-mode range carefully for unbalanced consumer-level source connections.

🏭

Industrial Differential Sensor Interface

The INA217AIDWT is appropriate for industrial systems that combine long sensor leads, substantial supply transients, and small differential outputs. Greater than 100 dB common-mode rejection reduces the impact of common-mode noise, while the ±4.5 V to ±18 V supply range supports dual-rail systems within that envelope. The 1.3 nV/√Hz noise figure is useful when amplification occurs before cable loss and downstream conversion. Industrial implementation still requires careful protection, grounding, and filtering beyond the amplifier itself. Place input protection where it will not leak into the precision input, use separate paths for sensor returns and actuator currents, and validate the complete signal chain over temperature. The manufacturer’s pin and application guidance should be followed before adding external protection components.

What is the INA217AIDWT?
The INA217AIDWT is a Texas Instruments monolithic instrumentation amplifier intended for differential receivers and low-level sensor measurement. According to the manufacturer product page, it provides 1.3 nV/√Hz noise at 1 kHz, 0.004% THD+N at 1 kHz with a gain of 100, an operating range of ±4.5 V to ±18 V, and a 16-pin SOIC wide-body package.
What are the key specifications of INA217AIDWT that engineers should know?
The INA217AIDWT combines 1.3 nV/√Hz input noise at 1 kHz with greater than 100 dB common-mode rejection and a gain-100 bandwidth of 800 kHz. Texas Instruments also specifies 0.004% THD+N at 1 kHz with a gain of 100 and a supply range of ±4.5 V to ±18 V. These figures position the device for precision differential signal extraction, bridge sensors, and instrumentation systems.
Where can I download the INA217AIDWT datasheet PDF?
The official INA217AIDWT datasheet is available through the Texas Instruments INA217 product page at https://www.ti.com/product/INA217. That page links to the manufacturer documentation and provides the part-specific ordering information, including the 16-pin DW package and -40 °C to +125 °C temperature range. Use the pin-description table in that datasheet when assigning PCB nets and the gain resistor.
Where can I find the INA217AIDWT pinout?
The INA217AIDWT pinout is defined in the pin-configuration section of the Texas Instruments INA217 datasheet, available from https://www.ti.com/product/INA217. The part uses the 16-pin DW wide-body SOIC outline and offers a 16-pin package option with the same pinout as the SSM2017. Assign signals from the manufacturer table rather than inferring connections from generic instrumentation-amplifier diagrams.
What is the input noise of INA217AIDWT?
The INA217AIDWT has an input noise density of 1.3 nV/√Hz at 1 kHz. According to the Texas Instruments INA217 datasheet, this low-noise characteristic is intended for differential receivers where the useful signal is close to the amplifier’s input-referred noise floor. Practical performance also depends on source impedance, resistor selection, gain bandwidth, and correct PCB grounding.
What is the bandwidth of INA217AIDWT at a gain of 100?
The INA217AIDWT provides 800 kHz bandwidth at a gain of 100. The manufacturer also lists an overall bandwidth of 3.4 MHz and a slew rate of 15 V/µs. Because the bandwidth changes with the externally programmed gain, confirm the response and stability at the actual resistor value and signal frequency used in the target circuit.
Can INA217AIDWT replace an SSM2017?
Yes, the INA217AIDWT is specifically identified by Texas Instruments as a replacement for the SSM2017 when using the 16-pin wide-body SOIC configuration. The manufacturer states that the INA217 is available in DIP-8 and SOL-16 wide-body packages with the same pinouts as the SSM2017. Confirm the selected SSM2017 package, gain resistor, supply limits, and full pin names before replacing it.
What is the best drop-in replacement for INA217AIDWT?
INA217AIDWR is the closest same-family drop-in choice because it uses the same INA217AIDW electrical configuration and 16-pin SOIC DW footprint; its distinguishing suffix identifies tape-and-reel shipment rather than the target’s tube packaging. For SSM2017-based designs, the INA217AIDWT itself is the manufacturer-described replacement. Check gain, supply, noise, bandwidth, and every pin connection before substituting any alternative.
Is INA217AIDWT suitable for low-level bridge sensors?
Yes, the INA217AIDWT is well suited to low-level differential bridge measurements because its 1.3 nV/√Hz input noise preserves small signals while greater than 100 dB common-mode rejection suppresses voltage common to both bridge nodes. The external gain resistor allows the amplifier gain to be matched to the sensor output and excitation level, while the 800 kHz gain-100 bandwidth supports many practical sensing bandwidths.
When should I choose INA217AIDWT over INA217AIDWR?
Choose INA217AIDWT when the required procurement format is a tube, and choose INA217AIDWR when tape-and-reel handling is required. Their core INA217AIDW electrical configuration and 16-pin DW package are the same, so the selection should follow production packaging requirements rather than signal-chain performance. Verify the orderable suffix and delivery format during purchasing.
INA217AIDWT versus INA217AIDWR: which package handling is better?
The INA217AIDWT and INA217AIDWR share the same 16-pin SOIC DW footprint and core INA217AIDW configuration, but they use different production packing formats. INA217AIDWT is the tube-format option, while INA217AIDWR is the tape-and-reel option. For automated pick-and-place, tape-and-reel may be more convenient; for small laboratory quantities, the tube format may be appropriate.
Is INA217AIDWT in stock?
Current INA217AIDWT inventory changes with order volume and regional supply conditions, so a reliable stock commitment should be requested through the Request a Quote form on this page. The same form can confirm the desired tube packaging, minimum order quantity, current lead time, and shipment schedule for the exact INA217AIDWT ordering code.
What is the price of INA217AIDWT?
The current commercial terms for INA217AIDWT should be obtained through the Request a Quote form on this page. A quote request can confirm quantity pricing, tube packaging availability, minimum order quantity, and lead time for the exact 16-pin DW ordering code. This avoids using an outdated catalog figure for a component whose supply status can change.
What is the lead time for INA217AIDWT?
The current lead time for INA217AIDWT depends on requested quantity, tube packaging, and manufacturing conditions. Submit the required quantity and target date through the Request a Quote form on this page so procurement can confirm availability and a committed delivery schedule. Texas Instruments identifies the INA217 family as an active product, but active status does not by itself guarantee immediate stock.
What compliance attributes apply to INA217AIDWT?
The INA217AIDWT is described as a green product with no antimony or bromine in its construction. Its exact RoHS, REACH, halogen-free, and conflict-minerals declarations should be confirmed on the Texas Instruments product page and in the applicable compliance documentation. The device is an industrial analog IC, so AEC-Q100 qualification is not applicable unless a separate automotive-qualified ordering option is specified.

Справочные инженерные данные для INA217AIDWT — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose INA217AIDWT when your circuit needs the INA217’s low-noise, high-CMR instrumentation-amplifier performance and the component will be supplied in the tube format. Its 1.3 nV/√Hz input noise, greater than 100 dB common-mode rejection, 800 kHz gain-100 bandwidth, and 0.004% THD+N at 1 kHz make it appropriate for bridge sensors, shunts, laboratory instrumentation, and precision differential acquisition. INA217AIDWR is the practical alternative when automated pick-and-place handling is preferred because its electrical configuration and 16-pin DW footprint remain the same. INA217AIDWTG4 is another same-family ordering option with the core configuration and footprint. For any substitution, verify the gain resistor, input common-mode limits, supply rails, differential input range, and SSM2017 pin compatibility. Use the target’s 16-pin wide-body outline rather than assuming compatibility with the INA217’s DIP-8 option.

Сравнение с аналогами

Параметр Этот товар INA217AIDWR INA217AIDWTG4
Package 16-pin SOIC wide-body (DW) 16-pin SOIC wide-body (DW) 16-pin SOIC wide-body (DW)
Brand Texas Instruments Texas Instruments Texas Instruments
Amplifier Type Monolithic instrumentation amplifier Monolithic instrumentation amplifier Monolithic instrumentation amplifier
Input Noise Density 1.3 nV/√Hz at 1 kHz 1.3 nV/√Hz at 1 kHz 1.3 nV/√Hz at 1 kHz
THD+N 0.004% at 1 kHz, gain = 100 0.004% at 1 kHz, gain = 100 0.004% at 1 kHz, gain = 100
Bandwidth at Gain 100 800 kHz 800 kHz 800 kHz
Supply Range ±4.5 V to ±18 V ±4.5 V to ±18 V ±4.5 V to ±18 V
Common-Mode Rejection >100 dB >100 dB >100 dB
Gain Configuration External gain-setting resistor External gain-setting resistor External gain-setting resistor

Ключевые отличия

  • Very low input noise for precision differential extraction (против INA217AIDWR)
  • Gain-100 bandwidth supports higher-speed measurement than slow precision-only front ends (против INA217AIDWTG4)
  • Direct manufacturer-described replacement path for SSM2017 designs (против INA217AIDWR)

Заметки по проектированию

Route the two input signals as a compact differential pair and place the external gain resistor close to its specified package pin. Keep the input network away from switching nodes, relay contacts, and high-current return paths. A quiet analog-ground region and short supply connections reduce errors that can otherwise dominate the device’s 1.3 nV/√Hz input noise. Use the manufacturer pin-description table for every net assignment rather than relying on a generic pin diagram.

Confirm the common-mode voltage at the pins, not only the differential signal amplitude, and verify the selected gain against the 800 kHz gain-100 bandwidth. The external gain resistor also contributes tolerance, temperature-coefficient, and parasitic-capacitance errors. For an SSM2017 replacement, verify that the original component used the 16-pin wide-body configuration and compare every connection, supply requirement, gain equation, and protection arrangement before energizing the board.

Treat the input connections as high-impedance precision nodes. Avoid long exposed test pads, unbonded connector leads, and shared copper with shunt or switching-current returns. If source impedances are not equal, account for their difference because the gain resistor and input bias current can convert imbalance into offset error. At high operating gains, use low-noise fixed resistors and maintain a clean, stable reference return around the entire measurement loop.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The manufacturer data describes INA217AIDWT as a green product with no Sb/Br. Specific RoHS, REACH, halogen-free, and conflict-minerals declarations should be checked on the TI product page. AEC-Q100 is not applicable to this industrial analog instrumentation amplifier ordering code.

Похожие запросы

INA217AIDWT datasheet INA217AIDWT pinout INA217AIDWT datasheet pdf INA217AIDWT equivalent INA217AIDWT replacement INA217AIDWT vs INA217AIDWR INA217AIDWT footprint INA217AIDWT application circuit INA217AIDWT price INA217AIDWT stock Texas Instruments INA217AIDWT INA217AIDWT 16 pin SOIC INA217AIDWT SSM2017 replacement

Связанные компоненты & термины

Texas Instruments INA217AIDWT INA217AIDWR INA217AIDWTG4 SSM2017 instrumentation amplifier differential amplifier signal-chain IC precision analog IC input-referred noise common-mode rejection ratio CMRR total harmonic distortion plus noise THD+N external gain-setting resistor 16-pin SOIC SOIC family wide-body surface-mount package RoHS REACH green product bridge sensor current-shunt monitoring laboratory instrumentation industrial sensor interface
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ