INA217AIDWT - Low-Noise Instrumentation Amplifier | Texas Instruments
MPN: INA217AIDWT ✓ فعالINA217AIDWT جائزہ
An instrumentation amplifier is a specialized amplifier that measures the voltage difference between two input signals while rejecting large common-mode voltages. The INA217 belongs to the instrumentation-amplifier hierarchy within signal-chain ICs, where low input noise, accurate gain control, and common-mode rejection are more important than general-purpose op-amp flexibility. The INA217 is also identified by Texas Instruments as a replacement for the SSM2017, with its 16-pin SOIC option providing the same package and pinout as the SSM2017.
The principal performance characteristics are 1.3 nV/√Hz noise at 1 kHz, greater than 100 dB common-mode rejection, and 800 kHz bandwidth at a gain of 100. Its total harmonic distortion plus noise remains only 0.004% at 1 kHz under that gain condition. Current-feedback circuitry supports wide bandwidth and dynamic response across a broad range of externally programmed gains, while the operating supply range accommodates precision laboratory, industrial, and instrumentation systems using dual rails.
The INA217 uses an external gain-setting resistor, allowing the closed-loop gain to be selected according to the application. This architecture makes the device appropriate for differential sensor interfaces where source impedance is known and signal gain must be adjusted. The 16-pin wide-body SOIC provides sufficient pin count for the input, output, supply, feedback, and gain-setting connections while retaining compatibility with the referenced SSM2017 footprint.
Typical uses include low-level bridge excitation and measurement, precision differential voltage acquisition, current-shunt monitoring, sensor-interface amplification, and laboratory instrumentation. In each case, the low-noise input stage preserves small differential signals, while common-mode rejection limits the effect of voltage shared by both input terminals. The wide supply range supports systems operating at rail voltages between 4.5 V and 18 V per rail.
The most important PCB consideration is to follow the manufacturer’s pin-description table and recommended decoupling layout. Input and supply connections should be short, the gain resistor should connect only to the specified gain pin, and grounding should avoid shared high-current return paths. Because the device is intended for precision signal extraction, component placement and source-impedance balancing are as important as the nominal noise specification.
This product page combines the INA217’s principal electrical characteristics, verified package information, sourcing guidance, replacement considerations, and application-focused engineering guidance. It also highlights where a drop-in replacement can preserve the PCB footprint and where original SSM2017 compatibility must be checked against the complete pin and electrical requirements.
کے لیے ڈراپ اِن متبادل INA217AIDWT — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
INA217AIDWR
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
INA217AIDWTG4
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
INA217AIDWT زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | 1-amplifier monolithic instrumentation amplifier |
| Input Noise Density | 1.3 nV/√Hz at 1 kHz |
| Total Harmonic Distortion Plus Noise | 0.004% at 1 kHz, gain = 100 |
| Bandwidth at Gain 100 | 800 kHz |
| Overall Bandwidth | 3.4 MHz |
| Supply Voltage Range | ±4.5 V to ±18 V |
| Common-Mode Rejection | >100 dB |
| Gain Configuration | Set by external resistor |
| Slew Rate | 15 V/µs |
| Maximum Differential Input Voltage | ±250 µV |
| آپریٹنگ درجہ حرارت رینج | -40 °C to +125 °C |
| پیکیج | 16-pin SOIC wide-body (DW) |
| ماؤنٹنگ ٹائپ | Surface mount |
| Number of Circuits | 1 |
| Replacement Reference | SSM2017 |
| RoHS اسٹیٹس | Green product, no Sb/Br |
INA217AIDWT 16-pin soic wide-body (dw) پن کنفیگریشن گائیڈ
INA217AIDWT (16-pin soic wide-body (dw) پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں INA217AIDWT.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
INA217AIDWT کے لیے موزوں ہے 6 ایپلیکیشنs: Precision Bridge Sensor Amplification, Low-Level Differential Voltage Acquisition, Current-Shunt Monitoring, Laboratory Instrumentation Front End, Balanced Audio and Communications Inputs, Industrial Differential Sensor Interface.
Precision Bridge Sensor Amplification
The INA217AIDWT fits bridge-based pressure, load, and strain measurements because its 1.3 nV/√Hz input noise limits the amplifier’s contribution to the measured signal while common-mode rejection above 100 dB rejects much of the voltage shared by the two bridge inputs. The external gain resistor makes the circuit scale simple and repeatable. At a gain of 100, the device retains 800 kHz bandwidth and has 0.004% THD+N at 1 kHz, providing useful bandwidth for slow mechanical signals and higher-speed force or vibration tests. Place the amplifier close to the bridge, balance source impedances, and return its output to a quiet analog ground to prevent sensor leads and PCB leakage from overwhelming the low-level differential output.
تجویز کردہ
Low-Level Differential Voltage Acquisition
For small differential voltages riding on a larger common-mode potential, the INA217AIDWT combines 1.3 nV/√Hz input noise with greater than 100 dB common-mode rejection. This makes it useful for frontend conditioning before a precision ADC, particularly where the source is a balanced sensor rather than a single-ended signal. The 800 kHz bandwidth at a gain of 100 supports measurement loops that need more bandwidth than a slow precision-only amplifier provides. A practical implementation should use short, shielded or tightly routed differential traces, matched input components where appropriate, and local supply bypassing. The gain resistor must follow the manufacturer circuit, and its tolerance and temperature coefficient become part of the overall gain error when the programmed gain is high.
تجویز کردہ
Current-Shunt Monitoring
The INA217AIDWT can amplify the small voltage generated across a current-sense shunt while rejecting the supply or load voltage common to both shunt terminals. Its 1.3 nV/√Hz input noise is valuable when the measured current produces only millivolts or microvolts, and common-mode rejection above 100 dB improves measurement integrity in systems with substantial bus voltage. The ±4.5 V to ±18 V supply range accommodates laboratory, industrial, and communications equipment. Keep the shunt’s Kelvin connections separate from its power terminals, place the amplifier near the shunt, and use a symmetric return path to prevent copper drops from entering the differential input. Verify the input common-mode range and differential input limits at the selected operating gain.
تجویز کردہ
Laboratory Instrumentation Front End
The INA217AIDWT suits laboratory instruments that measure weak differential signals while presenting substantial common-mode voltage, such as sensor conditioners, precision source interfaces, and multichannel measurement front ends. Its current-feedback architecture supports 800 kHz bandwidth at a gain of 100, while the 0.004% THD+N specification helps preserve waveform fidelity in signal-oriented tests. The 16-pin wide-body SOIC also offers enough routing flexibility for supply, feedback, and gain components. For best performance, use a clean analog supply, decouple close to the device, avoid sharing return-current paths with display or relay circuitry, and observe the input common-mode limits. The external gain resistor should be a low-noise, tightly toleranced component when measurement accuracy dominates.
تجویز کردہ
Balanced Audio and Communications Inputs
The INA217AIDWT can condition a balanced low-level audio or communications input when the design requires differential extraction and low input-referred noise. Its 1.3 nV/√Hz input noise and greater than 100 dB common-mode rejection help preserve small signal content while rejecting common-mode hum or coupled noise on the pair. The 0.004% THD+N figure at 1 kHz and gain of 100 makes it particularly relevant to high-fidelity measurement paths. The amplifier should be followed by suitable gain staging and filtering rather than treated as a general-purpose line output stage. Maintain balanced routing, keep the gain resistor close to the device, and isolate the input from digital switching paths. Check the common-mode range carefully for unbalanced consumer-level source connections.
تجویز کردہ
Industrial Differential Sensor Interface
The INA217AIDWT is appropriate for industrial systems that combine long sensor leads, substantial supply transients, and small differential outputs. Greater than 100 dB common-mode rejection reduces the impact of common-mode noise, while the ±4.5 V to ±18 V supply range supports dual-rail systems within that envelope. The 1.3 nV/√Hz noise figure is useful when amplification occurs before cable loss and downstream conversion. Industrial implementation still requires careful protection, grounding, and filtering beyond the amplifier itself. Place input protection where it will not leak into the precision input, use separate paths for sensor returns and actuator currents, and validate the complete signal chain over temperature. The manufacturer’s pin and application guidance should be followed before adding external protection components.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا INA217AIDWT — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | INA217AIDWR | INA217AIDWTG4 |
|---|---|---|---|
| Package | 16-pin SOIC wide-body (DW) | 16-pin SOIC wide-body (DW) | 16-pin SOIC wide-body (DW) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Type | Monolithic instrumentation amplifier | Monolithic instrumentation amplifier | Monolithic instrumentation amplifier |
| Input Noise Density | 1.3 nV/√Hz at 1 kHz | 1.3 nV/√Hz at 1 kHz | 1.3 nV/√Hz at 1 kHz |
| THD+N | 0.004% at 1 kHz, gain = 100 | 0.004% at 1 kHz, gain = 100 | 0.004% at 1 kHz, gain = 100 |
| Bandwidth at Gain 100 | 800 kHz | 800 kHz | 800 kHz |
| Supply Range | ±4.5 V to ±18 V | ±4.5 V to ±18 V | ±4.5 V to ±18 V |
| Common-Mode Rejection | >100 dB | >100 dB | >100 dB |
| Gain Configuration | External gain-setting resistor | External gain-setting resistor | External gain-setting resistor |
اہم امتیازی خصوصیات
- Very low input noise for precision differential extraction (بمقابلہINA217AIDWR)
- Gain-100 bandwidth supports higher-speed measurement than slow precision-only front ends (بمقابلہINA217AIDWTG4)
- Direct manufacturer-described replacement path for SSM2017 designs (بمقابلہINA217AIDWR)
ڈیزائن نوٹس
Route the two input signals as a compact differential pair and place the external gain resistor close to its specified package pin. Keep the input network away from switching nodes, relay contacts, and high-current return paths. A quiet analog-ground region and short supply connections reduce errors that can otherwise dominate the device’s 1.3 nV/√Hz input noise. Use the manufacturer pin-description table for every net assignment rather than relying on a generic pin diagram.
Confirm the common-mode voltage at the pins, not only the differential signal amplitude, and verify the selected gain against the 800 kHz gain-100 bandwidth. The external gain resistor also contributes tolerance, temperature-coefficient, and parasitic-capacitance errors. For an SSM2017 replacement, verify that the original component used the 16-pin wide-body configuration and compare every connection, supply requirement, gain equation, and protection arrangement before energizing the board.
Treat the input connections as high-impedance precision nodes. Avoid long exposed test pads, unbonded connector leads, and shared copper with shunt or switching-current returns. If source impedances are not equal, account for their difference because the gain resistor and input bias current can convert imbalance into offset error. At high operating gains, use low-noise fixed resistors and maintain a clean, stable reference return around the entire measurement loop.
تعمیل کی معلومات
The manufacturer data describes INA217AIDWT as a green product with no Sb/Br. Specific RoHS, REACH, halogen-free, and conflict-minerals declarations should be checked on the TI product page. AEC-Q100 is not applicable to this industrial analog instrumentation amplifier ordering code.