ISL81486IB - 5V 30Mbps RS-485/RS-422 Transceiver | Renesas
Артикул: ISL81486IB ✗ Снят с производстваISL81486IB Обзор
An RS-485/RS-422 transceiver is an interface IC that converts differential line signals into logic-level signals and converts logic-level transmit data back into differential outputs. The ISL81486 belongs to the broader transceiver hierarchy: interface IC, RS-485/RS-422 transceiver, and balanced data-communication interface. Such devices connect controllers, sensors, industrial equipment, and field buses to long, noise-prone cable networks.
The key operating characteristics include a 5V supply, half-duplex communication, a maximum specified signaling rate of 30Mbps, and support for both RS-485 and RS-422 applications. The BiCMOS implementation combines low-power CMOS behavior with bipolar output-driver capability. These characteristics make the device relevant to high-speed industrial links where data integrity and common-mode rejection are more important than low pin count.
Renesas identifies the ISL81486 family as a BiCMOS, 5V-powered single transceiver intended for balanced communication. The family was developed with the larger output voltage and higher data-rate capability required by high-speed PROFIBUS-style applications. The ISL81486IB ordering code is supplied in an 8-pin SOIC package, matching the 8-SOIC designation used in distributor product listings.
Typical uses include industrial controller interfaces, PROFIBUS-compatible equipment links, factory automation nodes, instrumentation gateways, and other balanced serial networks operating at elevated data rates. Because the transceiver is half-duplex, bus arbitration and transmit-enable control are central to the host-interface design. The external driver and receiver can also be used in opposite directions to implement a full-duplex RS-422 link when the application permits separate driver and receiver paths.
Design the bus with controlled-impedance differential routing, appropriate termination, common-mode protection, and a return path for the reference ground. Place protection devices close to the connector and keep the balanced traces short and symmetric. Verify operation against the required cable length, data rate, topology, and grounding arrangement because maximum Mbps capability does not by itself guarantee reliable communication over every field-bus installation.
This page combines manufacturer lifecycle information, package identification, functional characteristics, replacement considerations, and practical interface-design guidance. It also distinguishes verified drop-in candidates from package or function differences so engineers can assess legacy production continuity before releasing a redesign.
Аналоги без доработки для ISL81486IB — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ISL81486IB (тот же форм-фактор и посадочное место) — отличается по Package, Product Type.
ISL4486
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ISL81485IB
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →ISL81487IB
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →ISL81486IB Характеристики
| Product Type | Single RS-485/RS-422 transceiver |
| Driver and Receiver Count | 1 driver and 1 receiver |
| Напряжение питания | 5 V |
| Duplex Mode | Half duplex |
| Maximum Data Rate | 30 Mbps |
| Communication Standard | RS-485 and RS-422 |
| Logic and Driver Technology | BiCMOS |
| Корпус | 8-pin SOIC |
| Package Width | 3.90 mm |
| Тип монтажа | Surface mount |
| Termination Support | 8 termination connections |
| Ток покоя | 1.5 mA |
| Family Maximum Data Rate | Up to 40 Mbps |
| Automotive Qualification | Not qualified |
Руководство по цоколевке ISL81486IB в корпусе 3.90 mm
Цоколевка для ISL81486IB (корпус 3.90 mm). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для ISL81486IB.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
ISL81486IB подходит для 6 применениеs: High-Speed PROFIBUS Interface, Industrial Automation Controller, Factory Instrumentation Gateway, Data Acquisition Equipment, Motor and Machinery Control, Network Equipment Port.
High-Speed PROFIBUS Interface
The ISL81486IB fits PROFIBUS-oriented industrial nodes because the Renesas family combines a 5V half-duplex interface, one balanced driver, one balanced receiver, and data-rate capability specifically associated with high-speed PROFIBUS applications. Its listed 30Mbps maximum provides substantial signaling headroom compared with common low-speed field-bus nodes. Place the transceiver between the controller UART and the differential bus, enable the driver only during transmission, and apply the termination network required by the selected bus topology. Validate edge-rate behavior over the actual cable because the transceiver specification does not determine the complete PROFIBUS network’s margin.
Рекомендуется
Industrial Automation Controller
The ISL81486IB provides a compact interface between an industrial controller and a balanced field-bus network. Its single-driver, single-receiver arrangement supports half-duplex communication over one pair of bus conductors, while the 8-pin SOIC package keeps the footprint manageable on control hardware. The 30Mbps maximum rate is suitable for communication paths where deterministic timing and noise-resistant differential signaling are priorities. Implement an explicit transmit-enable state machine to prevent bus contention, connect the transceiver ground to the interface reference network, and confirm timing against the controller’s UART characteristics before production release.
Рекомендуется
Factory Instrumentation Gateway
The ISL81486IB can bridge a controller UART to a long differential instrument bus in a factory gateway. Differential RS-422 or RS-485 signaling improves noise tolerance compared with a single-ended interface, and the transceiver’s 30Mbps rated capability supports high-speed links when the installed cable and termination are appropriate. Keep the differential trace geometry continuous and add surge protection at the external connector. Since half-duplex operation requires direction control, use a hardware-controlled driver-enable signal and design the firmware turnaround timing to avoid transmitting while another node owns the bus.
Рекомендуется
Data Acquisition Equipment
The ISL81486IB is appropriate for data-acquisition equipment that must collect measurements from remote sensors over a balanced industrial bus. The 5V supply integrates with embedded control systems, and the single transceiver reduces the logic-channel count compared with separate driver and receiver ICs. Its 30Mbps maximum supports high-throughput acquisition buses, although actual sensor update rates will usually be lower. Configure the bus termination for the cable length, maintain a common reference ground, and test operation with the intended cable because connector transitions and long traces can reduce practical margin even when the transceiver itself meets its maximum data-rate specification.
Рекомендуется
Motor and Machinery Control
The ISL81486IB can support communication between machine-control electronics and remote motor-control modules where a robust differential interface is required. Its 30Mbps capability provides high signaling margin for short, controlled industrial wiring, while RS-485/RS-422 operation supports common-mode rejection in electrically noisy environments. Separate the transceiver’s ground reference from high-current motor returns and use a suitable interface ground strategy. Add protection at any cable leaving the enclosure, and verify driver-enable timing during emergency-stop or fault transitions so the node cannot unintentionally claim the bus.
Рекомендуется
Network Equipment Port
The ISL81486IB is applicable to specialized network equipment that terminates a balanced serial port rather than an Ethernet PHY. The 5V transceiver supports one half-duplex RS-485 or RS-422 link, and the 30Mbps rating permits high-rate communication over suitable point-to-point or multipoint wiring. For RS-422, the device’s driver and receiver may support complementary communication paths when the system wiring and enable requirements are compatible. Use controlled impedance and symmetrical routing from the transceiver to the connector, preserve a ground reference, and place any protection network where it will not add unacceptable imbalance to the differential pair.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ISL81486IB — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ISL4486 | ISL81485IB | ISL81487IB |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Product Type | Single RS-485/RS-422 transceiver | Single RS-485/RS-422 transceiver | Single RS-485/RS-422 transceiver | Single RS-485/RS-422 transceiver |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V |
Ключевые отличия
- Higher listed product-specific data rate than the related family documentation (против ISL4486)
- Exact manufacturer ordering-code identity for the target 8-pin SOIC design (против ISL81485IB)
- BiCMOS implementation supports balanced high-speed communication in one compact device (против ISL81487IB)
Заметки по проектированию
Route the RS-485/RS-422 differential pair as a controlled-impedance pair with matched trace lengths and continuous reference-plane support. Avoid placing digital clocks, switching-regulator nodes, and high-current return paths beneath the bus traces. Keep the transceiver close to the connector-side protection components, and terminate the cable at physically defined endpoints rather than at every node. A short, symmetric interface section reduces common-mode conversion and helps preserve the benefit of differential signaling.
Treat the driver-enable function as a bus-arbitration requirement rather than a simple on/off control. Disable the driver whenever the node is receiving, and prevent two nodes from enabling their drivers simultaneously. Validate enable polarity against the manufacturer pin description because changing that polarity during a redesign can create bus contention even when the transceiver and package appear interchangeable.
Provide a stable 5V rail with low impedance near the transceiver and follow the manufacturer’s recommended bypassing arrangement. Place the local bypass capacitor close to the supply and ground pins, using a short ground return that does not share high-current motor or relay paths. Decoupling alone cannot compensate for an improperly referenced ground system; establish the bus reference and chassis or protection-ground strategy before tuning component placement.
The listed 30Mbps capability is a device-level maximum, not a guarantee of reliable communication at every distance or topology. Verify the installed cable, node spacing, termination values, protection-device capacitance, and propagation-delay budget for the target protocol. Use oscilloscope measurements at the connector when commissioning, with the transceiver enabled for representative traffic patterns, to identify reflections, excessive common-mode conversion, or enable-timing overlap.
Информация о соответствии
Renesas identifies the ISL81486 family as obsolete and states that support is limited to customers that have already adopted these products. No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement is included in the cited product information.