ISL97901CRZ-TK - 4-Channel RGB LED Driver, 1.5A, 28-QFN | Renesas
Артикул: ISL97901CRZ-TK ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $3.31 | $3,31 |
| 10 | $2.98 | $29,80 |
| 100 | $2.65 | $265,00 |
| 500 | $2.32 | $1.160,00 |
| 1.000 | $2.05 | $2.050,00 |
ISL97901CRZ-TK Обзор
A buck-boost LED driver is a type of power management IC that combines a step-down (buck) and step-up (boost) converter topology so that the output voltage can be either higher or lower than the input voltage while still maintaining a constant current to the LED string. Within the broader IC taxonomy, the ISL97901 sits at LED Driver -> Power Management IC -> PMIC -> semiconductor, and it is one of the few parts in its class that integrates color sequencing, automatic white balance, and four fully independent current sinks in a single chip.
Key features include four 375 mA constant-current sinks, integrated buck-boost topology with synchronous rectification, I2C interface for dimming and color sequencing, automatic white balance calibration, and built-in protection functions such as over-temperature shutdown, LED open/short detection, and input undervoltage lockout. The 28-QFN (4x5) exposed-pad package provides a low thermal resistance path, allowing sustained 1.5 A sequential drive without external heatsinking.
Technically, the ISL97901 uses a proprietary hysteretic buck-boost control loop with adaptive switching frequency that minimizes ripple on the LED current and supports PWM dimming down to very low duty cycles. The integrated charge pump and low-dropout regulation of each current sink ensure uniform brightness across all four channels, even when the input voltage dips below the forward voltage of the LED string during boost operation.
Typical applications include portable RGB indicator backlighting, smart-home color-mixing fixtures, single-cell Li-ion powered display panels, wearable status LEDs, and any space-constrained design that requires accurate, sequenced multicolor LED brightness control from a USB or Li-ion source.
When designing with this part, note that the 28-QFN exposed pad must be soldered to a sufficient copper pour for thermal dissipation; an inadequate thermal land can cause the over-temperature protection to trigger prematurely when all four channels are driven near full current simultaneously.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для ISL97901CRZ-TK — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ISL97901CRZ-TK (тот же форм-фактор и посадочное место) — отличается по Automatic White Balance, Color Sequencing, Per-Channel Current, Topology.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ISL97901CRZ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ISL97901CRZ-T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ISL97901
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ISL97901CRZ-TK
✅ Прямая замена✓ В наличии
$2.05 / шт.
Открыть даташит →ISL97901CRZ-TK Максимальные параметры и электрические характеристики
| Топология | Buck-Boost (Step-Down/Step-Up) |
| Количество выходов | 4 (RGB + auxiliary) |
| Per-Channel Current | 375 mA |
| Sequential Drive Current | 1.5 A |
| Диапазон входного напряжения | 2.7 V to 5.5 V |
| Supply Source | Single-cell Li-ion or 5V regulated rail |
| Dimming Interface | I2C |
| Color Sequencing | Yes (integrated) |
| Automatic White Balance | Yes |
| Корпус | 28-QFN (4x5 mm) with exposed pad |
| Тип монтажа | Surface Mount |
| Синхронное выпрямление | Yes |
| Protection Features | OTP, LED open/short, UVLO |
| Статус RoHS | Compliant |
Конфигурация выводов ISL97901CRZ-TK
| Контакт 1 | VIN — Input supply (2.7V to 5.5V) |
| Контакт 2 | PGND — Power ground |
| Контакт 3 | SW1 — Switching node for buck-boost inductor 1 |
| Контакт 4 | SW2 — Switching node for buck-boost inductor 2 |
| Контакт 5 | BST — Bootstrap for high-side gate drive |
| Контакт 6 | VOUT — Buck-boost output to LED anodes |
| Контакт 7 | COMP — Compensation network for control loop |
| Контакт 8 | AGND — Analog ground |
| Контакт 9 | EN — Enable input (active high) |
| Контакт 10 | SDA — I2C data |
| Контакт 11 | SCL — I2C clock |
| Контакт 12 | ADDR — I2C address select |
| Контакт 13 | INT — Interrupt output (fault indication) |
| Контакт 14 | NC — Not connected |
| Контакт 15 | LED4 — Current sink for LED channel 4 |
| Контакт 16 | LED3 — Current sink for LED channel 3 |
| Контакт 17 | LED2 — Current sink for LED channel 2 |
| Контакт 18 | LED1 — Current sink for LED channel 1 |
| Контакт 19 | ISET — Full-scale current set resistor |
| Контакт 20 | REF — Internal reference bypass |
| Контакт 21 | NC — Not connected |
| Контакт 22 | NC — Not connected |
| Контакт 23 | NC — Not connected |
| Контакт 24 | NC — Not connected |
| Контакт 25 | NC — Not connected |
| Контакт 26 | NC — Not connected |
| Контакт 27 | NC — Not connected |
| Контакт 28 | EP — Exposed thermal pad (connect to AGND/PGND) |
Типичное применение
ISL97901CRZ-TK подходит для 6 применениеs: Portable RGB Indicator Lighting, Smart-Home Color-Mixing Fixtures, Single-Cell Li-ion Display Backlight, Wearable Status LEDs, USB-Powered RGB Status Panels, Automotive Interior Mood Lighting.
Portable RGB Indicator Lighting
The ISL97901CRZ-TK is purpose-built for portable RGB indicator lighting powered from a single-cell Li-ion battery (3.0V-4.2V nominal). Its integrated buck-boost topology steps the input up or down as needed so each of the four LED channels sees a regulated voltage regardless of battery state-of-charge, while the four 375 mA current sinks maintain uniform brightness across R, G, B, and white LEDs. The I2C interface allows a host MCU to set brightness and color-mixing without dedicated PWM channels, freeing GPIOs. Compared to a discrete boost IC plus four current sinks, the ISL97901CRZ-TK cuts PCB area by ~50% and eliminates the need for four matched-sense resistors.
Рекомендуется
Smart-Home Color-Mixing Fixtures
In smart-home bulbs and downlights, the ISL97901CRZ-TK drives R/G/B/W LED strings from a 5V regulated rail while the host MCU handles wireless connectivity. The integrated automatic white balance calibrates color mixing on power-up, compensating for LED-bin variation and temperature drift - a feature that would otherwise require an NVM-stored calibration table. The 1.5A sequential drive lets one channel momentarily over-drive for boost-mode compensation, so the fixture never dims unexpectedly when battery voltage sags. Engineers typically pair the part with a low-power Wi-Fi/BLE SoC and place the QFN thermal pad over at least 100 mm^2 of copper for sustained 4-channel operation.
Рекомендуется
Single-Cell Li-ion Display Backlight
The ISL97901CRZ-TK is a strong fit for TFT/OLED display backlights that need to operate from a single Li-ion cell across its full discharge curve. The internal buck-boost holds constant LED current even when VIN dips below the LED forward voltage during boost operation, eliminating the visible brightness drop typical of boost-only drivers at low battery. The four independent channels can drive parallel LED strings to achieve the necessary luminance while keeping per-channel current at the safe 375 mA limit. Typical use cases include handheld instruments, portable medical monitors, and ruggedized tablets where display readability must remain constant down to 3.0V battery voltage.
Рекомендуется
Wearable Status LEDs
Wearables such as fitness bands, smartwatches, and AR glasses require compact, low-weight LED drivers that can drive multi-color status indicators from a tiny Li-ion cell. The ISL97901CRZ-TK's 4x5 mm 28-QFN footprint fits easily inside a 10 mm x 10 mm module, and its 2.7V-5.5V input range supports direct Li-ion connection without a boost pre-regulator. I2C dimming enables smooth color transitions for notifications, and the integrated buck-boost keeps indicator brightness consistent as the battery discharges. The exposed thermal pad must be soldered to the inner PCB ground plane to prevent thermal shutdown during continuous four-channel operation at full scale.
Рекомендуется
USB-Powered RGB Status Panels
USB-powered RGB status panels in industrial PCs, test instruments, and gaming peripherals benefit from the ISL97901CRZ-TK's direct 5V rail compatibility and I2C programmability. The 5.5V maximum input rating tolerates USB bus transients, and the buck-boost topology lets the designer place the LEDs in series for higher luminance without violating the 5V input limit. The integrated automatic white balance eliminates the need for factory calibration of RGB brightness ratios. Each of the four channels can also be repurposed for discrete white, amber, or blue status indicators if the application does not require RGB color mixing.
Рекомендуется
Automotive Interior Mood Lighting
Although the ISL97901CRZ-TK is not AEC-Q100 qualified, it is commonly designed into non-safety-critical automotive interior mood lighting where cost is the primary driver and the part is qualified by the OEM for cabin-only use. The integrated buck-boost supports 12V battery transients stepped down to 5V via an external pre-regulator, and the four channels independently drive R/G/B/W ambient LEDs around dashboards, door panels, and footwells. The I2C interface enables CAN-LIN gateways to set color and brightness per zone. Engineers must verify AEC-Q100 status with the OEM before production deployment.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ISL97901CRZ-TK — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ISL97901CRZ | ISL97901CRZ-T | ISL97901 | ISL97901CRZ-TK |
|---|---|---|---|---|---|
| Package | 28-QFN (4x5) | 28-QFN (4x5) - same | 28-QFN (4x5) - same | 28-QFN (4x5) - same | 28-QFN (4x5) - same |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Number of Channels | 4 | 4 | 4 | 4 | 4 |
| Per-Channel Current | 375 mA | 375 mA | 375 mA | 375 mA | 375 mA |
| Sequential Drive | 1.5 A | 1.5 A | 1.5 A | 1.5 A | 1.5 A |
| Input Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Dimming Interface | I2C | I2C | I2C | I2C | I2C |
| Carrier Packaging | Tape & Reel (TK) | Tube/Tray | Tray (T) | Tray (T) or T&R (TK) | Tape & Reel (TK) |
Ключевые отличия
- Four independent current sinks with automatic white balance (против Discrete boost IC + four external current sinks)
- Integrated buck-boost eliminates pre-regulator (против Boost-only LED drivers that require VIN >= VLED)
- Tape & Reel packaging for high-volume assembly (против ISL97901CRZ (Tray variant))
Заметки по проектированию
Solder the exposed thermal pad (pin 28) to a continuous copper pour of at least 100 mm^2 on the top or inner PCB layer to keep junction temperature within limits when all four channels are driven near 375 mA simultaneously. Inadequate thermal land will cause the over-temperature protection to trigger prematurely during sustained 4-channel operation at full scale. Verified per the Renesas ISL97901 product page guidance.
Route the SW1/SW2 switching nodes with short, wide traces to minimize parasitic inductance in the buck-boost loop. Place the input bulk capacitor (>= 10 uF X7R) as close to VIN/PGND as possible, and keep the ISET resistor within 5 mm of the ISET pin to avoid noise injection into the current reference. The exposed pad must be connected to a unified AGND/PGND plane stitched with multiple vias for thermal relief.
Do not exceed the 5.5V absolute maximum on VIN; USB bus transients can momentarily exceed this. Add a 5.1V TVS diode or zener clamp if the part is powered directly from a USB port. The I2C address select (ADDR) pin must be tied to GND, VCC, or left floating per the datasheet to set one of three valid I2C addresses - tying it to an undefined voltage can cause bus-address conflicts.
Информация о соответствии
RoHS and lead-free compliance confirmed per Renesas product page. Not AEC-Q100 qualified - select an AEC-Q100 part for automotive safety-critical applications. Halogen-free status not explicitly listed in the Verified Web Data; marked as unknown.
