Texas Instruments

LM239DRG4 - Quad Open-Collector Comparator | Texas Instruments

Артикул: LM239DRG4 ✗ Снят с производства
Single supply or dual supply Vdss 3.5 nA Id 14-pin SOIC Package
MOQ: 1 |

LM239DRG4 Обзор

Texas Instruments LM239DRG4 is a commercial-grade quad differential comparator with four independent comparison channels, open-collector outputs, single- or dual-supply operation, and a 14-pin SOIC package. The device is intended for industrial and commercial equipment operating from -25°C to +85°C, and its open-collector outputs can pull a logic rail low when a defined sink current is available.

A comparator is an analog signal-conditioning integrated circuit that evaluates a voltage at its non-inverting input against a voltage at its inverting input. The resulting digital output indicates which input is higher. Within the broader electronics hierarchy, the LM239 belongs to the comparator family, which is part of analog interface and signal-conditioning ICs used between sensors, analog measurement circuits, and digital control logic.

The LM239DRG4 provides four differential comparators in one package. Its open-collector outputs are compatible with TTL, MOS, and CMOS logic according to the manufacturer information, allowing each output to operate as a wired-AND node when connected to a suitable pull-up. This architecture is useful when several signals must be monitored or when the output must directly interface with an open-collector bus. The commercial-grade temperature range supports controlled industrial environments rather than extended automotive or military temperature classes.

The manufacturer describes wide single-supply or dual-supply operation, low input bias current, and low supply-current drain. Published family information identifies a typical low input bias current of 3.5 nA and a typical low supply-current drain of 0.8 mA for the legacy LM239 family. These characteristics reduce the loading imposed on high-impedance sensing circuits and make the device appropriate for battery-powered, industrial-control, and analog front-end systems where every microamp of supply demand can affect available operating time.

Typical uses include overvoltage and undervoltage supervision, sensor threshold detection, window-comparator systems, motor and actuator control, and conversion of analog measurements into logic-level decisions. The four channels may also be configured for independent sensing, hysteresis, or multi-rail monitoring. Because each output is open collector, a pull-up resistor is required for normal high-state operation, and designers must verify that the selected pull-up voltage and sink current satisfy the device limits.

Board design should reserve the exposed package leads and maintain adequate copper around the 14-pin SOIC footprint. Input traces should be kept short and separated from switching nodes to reduce differential noise pickup. At each comparison threshold, verify input offset, common-mode range, propagation delay, and output pull-up timing. Do not exceed the family supply or input-voltage ratings, and account for the open-collector output's finite rise time when driving capacitive loads.

This product page consolidates lifecycle status, package details, functional characteristics, drop-in options, application guidance, and design notes for engineers evaluating the LM239DRG4. It also distinguishes direct replacements from legacy package variants and explains where pull-up resistors, input filtering, output loading, and thermal verification require attention.

Аналоги без доработки для LM239DRG4 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с LM239DRG4 (тот же форм-фактор и посадочное место) — отличается по Comparator Type, Logic Compatibility, Response Time, Output Type, Package.

Texas Instruments
Comparator Type: Quad precision differential voltage comparator
Response Time: 1.3 µs typical
Output Type: Open-collector
Сравнить с LM239DRG4 →
Texas Instruments
Logic Compatibility: TTL, MOS, and CMOS-compatible output
Response Time: 1 µsec
Output Type: Open-collector
Сравнить с LM239DRG4 →
Texas Instruments
Comparator Type: General Purpose
Logic Compatibility: TTL, MOS, CMOS
Output Type: Open-Collector
Сравнить с LM239DRG4 →
Texas Instruments
Comparator Type: General-purpose differential comparator
Logic Compatibility: TTL, MOS, and CMOS
Response Time: 1 µs
Сравнить с LM239DRG4 →

LM239DR

✅ Прямая замена
Texas Instruments
📦 14-SOIC
Quad precision differential voltage comparator · 4 independent channels · ±15 V or 30 V · Open-collector · 25 nA typical · ±5.0 nA typical · 2 mV maximum for LM239A family variants; LM239DR-specific value not supplied · 1.3 µs typical

Уточнить цену

Открыть даташит →

LM239ADR

✅ Прямая замена
📦 14-SOIC
Same LM239 comparator family and 14-SOIC format; RoHS, temperature grade, and exact suffix differences require comparison.

📋 Справочный аналог (нет в каталоге)

LM339D

✅ Прямая замена
Texas Instruments
📦 14-SOIC
4 · General-purpose differential voltage comparator · Open-collector · Single or split supply · Up to 38 V · 0.37 mV · 3.5 nA · 200 µA per comparator

Уточнить цену

Открыть даташит →

LM339DR

✅ Прямая замена
Texas Instruments
📦 14-SOIC
4 (Quad) · General Purpose · Open-Collector · 2 V to 36 V · ±1 V to ±18 V · 5 mV · 25 nA · 5 nA

✓ В наличии

$0.0738 / шт.

Открыть даташит →

LM2901HYDT

✅ Прямая замена
📦 14-SOIC
Pin-compatible 14-SOIC option with -40°C minimum temperature and 2 mV offset, but supply current rises from 2 mA to 2.5 mA.

📋 Справочный аналог (нет в каталоге)

LM239DRG4 Максимальные параметры и электрические характеристики

Comparator Configuration Quad differential comparator
Number of Channels 4 channels
Тип выхода Open collector
Supply Configuration Single supply or dual supply
Typical Single-Supply Voltage 3 V to 15 V
Typical Dual-Supply Voltage ±3 V, ±5 V, ±9 V, or ±12 V
Maximum Typical Dual-Supply Voltage ±15 V
Typical Input Bias Current 3.5 nA
Typical Supply-Current Drain 0.8 mA
Typical Response Time 1.3 us
Input Common-Mode Range Includes ground
Differential Input Voltage Range ±38 V
Output Compatibility TTL, MOS, and CMOS
Диапазон рабочих температур -25°C to +85°C
Корпус 14-pin SOIC
Тип монтажа Surface mount

Конфигурация выводов LM239DRG4

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
Контакт 1 OUT1 — Open-collector output for comparator channel 1
Контакт 2 IN1- — Inverting input for comparator channel 1
Контакт 3 IN1+ — Non-inverting input for comparator channel 1
Контакт 4 GND — Ground connection
Контакт 5 IN2+ — Non-inverting input for comparator channel 2
Контакт 6 IN2- — Inverting input for comparator channel 2
Контакт 7 OUT2 — Open-collector output for comparator channel 2
Контакт 8 OUT3 — Open-collector output for comparator channel 3
Контакт 9 IN3- — Inverting input for comparator channel 3
Контакт 10 IN3+ — Non-inverting input for comparator channel 3
Контакт 11 VCC — Positive supply connection
Контакт 12 IN4+ — Non-inverting input for comparator channel 4
Контакт 13 IN4- — Inverting input for comparator channel 4
Контакт 14 OUT4 — Open-collector output for comparator channel 4

Типичное применение

LM239DRG4 подходит для 6 применениеs: Industrial Voltage Supervision, Battery-Powered Sensor Interface, Motor and Actuator Control, Window and Limit Comparison, TTL and CMOS Logic Interfacing, Legacy Equipment Maintenance.

🏭

Industrial Voltage Supervision

The LM239DRG4 is suitable for monitoring multiple industrial voltage thresholds because four differential comparator channels are integrated in one 14-pin SOIC package. Each channel can compare a sensed supply or divided signal against a reference, while its open-collector output can directly pull a relay, relay-driver input, or PLC interface low. The commercial operating range of -25°C to +85°C matches controlled equipment environments. In practice, designers should verify the common-mode input range at every measured voltage, provide a suitable output pull-up, and account for input offset when setting narrow alarm thresholds.

🔋

Battery-Powered Sensor Interface

The LM239DRG4 can convert slow-moving sensor signals into logic decisions in battery-powered monitoring equipment. Its typical 3.5 nA input bias current limits loading of high-impedance sensing nodes, and the family's typical 0.8 mA supply-current drain helps constrain continuous power demand. Four thresholds can be implemented in one package rather than requiring four separate comparators. The primary trade-off is that the open-collector outputs need pull-up resistors, whose current and switching speed should be selected to balance battery consumption against required response timing.

⚡

Motor and Actuator Control

The LM239DRG4 can serve as the threshold-detection stage in motor, actuator, and power-driver control systems. Its differential inputs accept a command signal and feedback reference, allowing each channel to detect when a control quantity crosses a defined boundary. The open-collector output is useful for driving the input of a suitable driver or interface stage rather than directly driving a high-current load. Designers should keep switching-node wiring away from the high-impedance inputs and verify the response time of 1.3 us against the required fault-detection and shutdown delay.

📏

Window and Limit Comparison

A window comparator can use two LM239DRG4 channels to detect whether a monitored signal lies between an upper and lower limit, while the other channels monitor additional rails or conditions. The device's differential architecture permits a precision reference to be applied to one input and the scaled measured signal to the other. Hysteresis can be introduced with positive feedback to prevent output chatter near the threshold. Because four channels share one package, grounding and supply bypassing are particularly important; keep the reference path quiet and use local high-frequency bypass capacitance at pin 11.

🖥️

TTL and CMOS Logic Interfacing

The LM239DRG4 open-collector outputs are compatible with TTL, MOS, and CMOS logic according to the manufacturer information, making the device useful for bridging analog decisions to digital systems. A pull-up resistor establishes the high output state, while the comparator sinks current in the low state. This arrangement also permits multiple channels to share a bus node for wired-AND behavior. When choosing the pull-up value, balance reduced low-state current against slower rise time caused by bus capacitance, and ensure the connected logic input's thresholds and leakage remain within the comparator's output-current limits.

🔧

Legacy Equipment Maintenance

LM239DRG4 is relevant to maintenance and continuity programs that must reproduce an original industrial or commercial control board containing the obsolete LM239 comparator. Its 14-pin SOIC footprint and established four-channel open-collector architecture allow a qualified replacement to be considered without changing the board outline. Before substitution, review the original schematic and verify supply polarity, input common-mode limits, differential input limits, output pull-up arrangement, and temperature requirements. Lifecycle qualification and component traceability are essential when the equipment is expected to remain in service for many years.

What is the LM239DRG4?
The LM239DRG4 is a Texas Instruments commercial-grade quad differential comparator with four open-collector outputs in a 14-pin SOIC package. According to the LM239 manufacturer datasheet, it supports single or dual supplies, has a common-mode input range that includes ground, and provides outputs compatible with TTL, MOS, and CMOS logic. Each channel can compare an inverting input with a non-inverting input, making the device suitable for threshold detection, voltage supervision, and analog-to-logic interfacing.
What are the key specifications of LM239DRG4 that engineers should know?
The LM239DRG4 combines four differential comparator channels, open-collector outputs, and single- or dual-supply operation in a 14-pin SOIC package. The manufacturer information identifies typical input bias current of 3.5 nA, typical family supply-current drain of 0.8 mA, a typical response time of 1.3 us, and an operating-temperature range of -25°C to +85°C. Its differential input range extends to ±38 V, while the common-mode input range includes ground.
Is LM239DRG4 still in production?
No. The Texas Instruments LM239DRG4 orderable-parts page states that LM239DRG4 is no longer in production, so its lifecycle status is obsolete. Designs using this exact device should evaluate a current drop-in replacement and verify the replacement's supply range, offset, response time, temperature grade, output structure, and RoHS documentation before production release. Request current lifecycle confirmation and sourcing support through the Request a Quote form on this page.
Where can I download the LM239DRG4 datasheet PDF?
The official LM239 datasheet is available through the Texas Instruments LM239 product and part-details pages linked from this page. The manufacturer describes LM239DRG4 as a 14-SOIC quad differential comparator and lists the family data sheet as the controlling technical document. Use the manufacturer's PDF for the complete electrical characteristics, recommended operating conditions, pin configuration, and application guidance rather than relying on a distributor mirror or secondary summary.
Where is the LM239DRG4 pinout?
The LM239DRG4 uses a conventional 14-pin SOIC comparator pinout: pins 1 and 8 are OUT1 and OUT3, pins 7 and 14 are OUT4 and OUT2, pins 2, 3, 6, 9, 10, 12, and 13 are differential inputs, pin 4 is ground, and pin 11 is the positive supply. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks and confirm orientation from the package dot or lead-1 marker.
What is the LM239DRG4 supply voltage range?
The LM239DRG4 can operate from a single supply or from symmetrical dual supplies. The product information lists typical single-supply operation from 3 V to 15 V and typical dual-supply configurations of ±3 V, ±5 V, ±9 V, and ±12 V, with ±15 V as the maximum listed typical dual-supply level. Confirm absolute maximum ratings and input constraints against the manufacturer datasheet for the exact operating condition.
Why does the LM239DRG4 output require a pull-up resistor?
Each LM239DRG4 output is open collector, meaning the device can actively pull the output low but cannot source a high output current. A pull-up resistor establishes the high logic level and also allows multiple open-collector outputs to share a wired-AND node. Select the resistor so its sink current remains within the output rating while its rising edge remains fast enough for the downstream logic, and account for the additional capacitive rise time at slower pull-up values.
Can LM239DRG4 operate from a single 5 V supply?
Yes. The LM239 family supports single-supply operation, and the published LM239DRG4 product information includes 5 V within the typical 3 V to 15 V single-supply range. Connect the positive supply to pin 11 and ground to pin 4, place the required bypass capacitor close to the supply pins, and verify that every input signal remains inside the valid common-mode range. The open-collector output still requires an appropriate pull-up.
Is LM239DRG4 suitable for battery-powered equipment?
The LM239DRG4 can be suitable for low-power monitoring because the legacy LM239 family has a typical supply-current drain of 0.8 mA and a typical input bias current of 3.5 nA. Its four channels let one package monitor several thresholds, reducing board area and potentially avoiding several discrete comparators. Actual battery suitability depends on the complete operating duty cycle, pull-up resistance, leakage current, and the minimum supply voltage needed by the selected comparator variant.
What is the best drop-in replacement for LM239DRG4?
The closest direct replacement is the LM239DR because it retains the LM239 function, commercial grade, open-collector output, and 14-pin SOIC footprint. LM239ADR, LM339D, and LM339DR can also share the 14-pin SOIC form, but their temperature grades and exact electrical limits should be checked. The TI product page states that the LM339B is a drop-in replacement for LM239, LM339, and LM2901, making the B-version family a useful legacy-sourcing path.
Can LM2901HYDT replace LM239DRG4?
Yes, LM2901HYDT is identified as pin-compatible with LM239DRG4 and provides an alternate 14-pin SOIC sourcing option. The replacement has a lower operating-temperature limit of -40°C and a tighter input-offset specification of 2 mV, but its supply current is higher at 2.5 mA versus 2 mA for the cited comparison. Confirm the exact pin arrangement, output ratings, and legacy termination requirements before substituting it into an existing board.
LM239DRG4 vs LM339D — which is better for industrial control?
Choose LM239DRG4 when the original design specifically requires the LM239 commercial-grade behavior and its original qualification documentation. Choose LM339D only after checking its temperature range, supply ratings, offset, and propagation delay against the system requirements. Both devices are described as quad differential comparators in 14-pin SOIC packages, so the mechanical fit may match, but a footprint match alone does not establish that every operating limit is equivalent.
When should I choose LM239DRG4 instead of a dual comparator?
Choose the LM239DRG4 when the design needs four independent threshold comparisons and can benefit from integrating them into one 14-pin package. A dual comparator such as LM2902 requires more than one device for four channels, increasing board area, supply connections, and inventory complexity. The trade-off is that the quad device does not provide independent shutdown or enable control for each channel, so applications requiring channel isolation should account for that limitation.
Where can I buy LM239DRG4 and what is its price?
Use the Request a Quote form on this page to ask about LM239DRG4 availability, obsolete-part allocation, minimum order quantity, and lead time. Because the manufacturer states that LM239DRG4 is no longer in production, supply may depend on remaining factory inventory or a lifecycle allocation rather than routine new-production stock. The form provides a single quote path for the exact 14-SOIC ordering code and requested quantity.
What is the lead time and stock status for LM239DRG4?
LM239DRG4 is obsolete and no longer in production according to the Texas Instruments part-details page, so no routine lead time can be represented as a standard active-part commitment. Current remaining stock and allocation status should be confirmed through the Request a Quote form on this page. For an approved new design, request lifecycle status and an alternative quotation for a current or qualified drop-in comparator at the same operating limits.
What is the best cross-brand equivalent for LM239DRG4?
The manufacturer cross-reference information does not identify a specific cross-brand 14-pin SOIC equivalent in the available records, so selecting one without a verified pin and specification match would be speculative. The documented direct-replacement path is the LM239/LM339 B-version family, including LM339B as stated by Texas Instruments. A cross-brand candidate should be accepted only after its exact pinout, differential input range, output sink current, common-mode range, response time, and temperature grade are verified.

Справочные инженерные данные для LM239DRG4 — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose LM239DRG4 when maintaining an existing design that specifically uses the original commercial-grade LM239 in a 14-pin SOIC footprint and four open-collector comparison channels. Choose LM239DR for the most direct same-family continuity, and review LM239ADR when its suffix-specific environmental and compliance qualifications are preferable. LM339D or LM339DR can support board-level continuity when their temperature ratings and electrical limits pass review. LM2901HYDT is appropriate when the board can use its cited pin compatibility and its lower -40°C temperature limit, but its 2.5 mA supply current may reduce the operating-time advantage of the original part. Because LM239DRG4 is no longer in production, every substitution should include a pin-by-pin review, input common-mode analysis, pull-up recalculation, lifecycle review, and qualification for the target industrial environment.

Сравнение с аналогами

Параметр Этот товар LM239DR LM239ADR LM339D LM339DR LM2901HYDT
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 14-SOIC 14-SOIC 14-SOIC 14-SOIC 14-SOIC 14-SOIC
Comparator Configuration Quad differential comparator Quad differential comparator Quad differential comparator Quad differential comparator Quad differential comparator Quad differential comparator

Ключевые отличия

  • Four comparator channels in one package (против LM2902N/PB)
  • Lower cited supply current than the pin-compatible LM2901HYDT (против LM2901HYDT)
  • Commercial temperature range differs from the cited LM2901HYDT range (против LM2901HYDT)
  • Direct LM239 family continuity (против LM339D)

Заметки по проектированию

Every open-collector output needs a pull-up resistor for normal high-state operation. Size the resistor so the maximum low-state sink current remains within the comparator's output rating, while also meeting the downstream device's rise-time requirement. Multiple LM239DRG4 outputs may share a common pull-up to form a wired-AND node. Do not connect an output directly to a supply rail or assume it can source current.

Place the supply bypass capacitor close to pin 11 and the ground return to pin 4, with a short and low-inductance path between the two. Route the high-impedance differential inputs away from switching-node copper, relay wiring, and inductor fields. Input filtering can reduce noise but adds response delay, so verify that the added filtering remains compatible with the application's 1.3 us typical response time.

Operate the device only within the approved single- or dual-supply configuration and check the common-mode input range at both power-up and fault conditions. Although the differential input range extends to ±38 V, that rating does not make every input voltage valid for all supply configurations. Apply power-down protection to external signal sources that could back-power the inputs while the comparator supply is off.

Do not treat the LM239, LM339, and LM2901 family names as automatically identical in every respect. Verify operating temperature, supply voltage, input offset, response time, output current, qualification, and orderable suffix. For LM2901HYDT specifically, the cited comparison shows a -40°C minimum temperature and 2 mV offset but higher supply current than LM239DRG4, so substitution requires a functional review rather than a footprint-only decision.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The manufacturer part-details page identifies LM239DRG4 as no longer in production. A separate legacy comparison notes that LM2901HYDT deletes the G4 RoHS3 waiver; no definitive RoHS or REACH declaration for LM239DRG4 was established, so those fields remain unknown.

Данные проверены: 2026-11-15 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

LM239DRG4 LM239DRG4 datasheet LM239DRG4 pinout LM239DRG4 datasheet pdf LM239DRG4 equivalent LM239DRG4 replacement LM239DRG4 cross reference LM239DRG4 vs LM339D Texas Instruments LM239DRG4 LM239DRG4 14-SOIC footprint LM239DRG4 application circuit LM239DRG4 price LM239DRG4 stock LM239DRG4 obsolete replacement

Связанные компоненты & термины

Texas Instruments LM239DRG4 LM239DR LM239ADR LM339D LM339DR LM2901HYDT LM339B quad differential comparator comparator IC analog interface IC signal conditioning open-collector output wired-AND TTL MOS logic CMOS logic common-mode input voltage differential input voltage input offset voltage input bias current supply-current drain 14-pin SOIC SOIC-14 package surface-mount package
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ