LM239DRG4 - Quad Open-Collector Comparator | Texas Instruments
MPN: LM239DRG4 ✗ Cuối đờiLM239DRG4 Tóm tắt
A comparator is an analog signal-conditioning integrated circuit that evaluates a voltage at its non-inverting input against a voltage at its inverting input. The resulting digital output indicates which input is higher. Within the broader electronics hierarchy, the LM239 belongs to the comparator family, which is part of analog interface and signal-conditioning ICs used between sensors, analog measurement circuits, and digital control logic.
The LM239DRG4 provides four differential comparators in one package. Its open-collector outputs are compatible with TTL, MOS, and CMOS logic according to the manufacturer information, allowing each output to operate as a wired-AND node when connected to a suitable pull-up. This architecture is useful when several signals must be monitored or when the output must directly interface with an open-collector bus. The commercial-grade temperature range supports controlled industrial environments rather than extended automotive or military temperature classes.
The manufacturer describes wide single-supply or dual-supply operation, low input bias current, and low supply-current drain. Published family information identifies a typical low input bias current of 3.5 nA and a typical low supply-current drain of 0.8 mA for the legacy LM239 family. These characteristics reduce the loading imposed on high-impedance sensing circuits and make the device appropriate for battery-powered, industrial-control, and analog front-end systems where every microamp of supply demand can affect available operating time.
Typical uses include overvoltage and undervoltage supervision, sensor threshold detection, window-comparator systems, motor and actuator control, and conversion of analog measurements into logic-level decisions. The four channels may also be configured for independent sensing, hysteresis, or multi-rail monitoring. Because each output is open collector, a pull-up resistor is required for normal high-state operation, and designers must verify that the selected pull-up voltage and sink current satisfy the device limits.
Board design should reserve the exposed package leads and maintain adequate copper around the 14-pin SOIC footprint. Input traces should be kept short and separated from switching nodes to reduce differential noise pickup. At each comparison threshold, verify input offset, common-mode range, propagation delay, and output pull-up timing. Do not exceed the family supply or input-voltage ratings, and account for the open-collector output's finite rise time when driving capacitive loads.
This product page consolidates lifecycle status, package details, functional characteristics, drop-in options, application guidance, and design notes for engineers evaluating the LM239DRG4. It also distinguishes direct replacements from legacy package variants and explains where pull-up resistors, input filtering, output loading, and thermal verification require attention.
Bộ thay thế dễ dàng lắp đặt cho LM239DRG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM239DRG4 (cùng hình factor và footprint) — khác nhau ở Comparator Type, Logic Compatibility, Response Time, Output Type, Package.
LM239DR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM239ADR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM339D
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM339DR
✅ Drop-In✓ Còn hàng
$0.0738 / Đơn vị
Xem tài liệu →LM2901HYDT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM239DRG4 Tỷ lệ tối đa & tính chất điện
| Comparator Configuration | Quad differential comparator |
| Number of Channels | 4 channels |
| Kiểu đầu ra | Open collector |
| Supply Configuration | Single supply or dual supply |
| Typical Single-Supply Voltage | 3 V to 15 V |
| Typical Dual-Supply Voltage | ±3 V, ±5 V, ±9 V, or ±12 V |
| Maximum Typical Dual-Supply Voltage | ±15 V |
| Typical Input Bias Current | 3.5 nA |
| Typical Supply-Current Drain | 0.8 mA |
| Typical Response Time | 1.3 us |
| Input Common-Mode Range | Includes ground |
| Differential Input Voltage Range | ±38 V |
| Output Compatibility | TTL, MOS, and CMOS |
| Khoảng nhiệt độ hoạt động | -25°C to +85°C |
| Hộp | 14-pin SOIC |
| Kiểu lắp đặt | Surface mount |
Cấu hình chân LM239DRG4
| Chân 1 | OUT1 — Open-collector output for comparator channel 1 |
| Chân 2 | IN1- — Inverting input for comparator channel 1 |
| Chân 3 | IN1+ — Non-inverting input for comparator channel 1 |
| Chân 4 | GND — Ground connection |
| Chân 5 | IN2+ — Non-inverting input for comparator channel 2 |
| Chân 6 | IN2- — Inverting input for comparator channel 2 |
| Chân 7 | OUT2 — Open-collector output for comparator channel 2 |
| Chân 8 | OUT3 — Open-collector output for comparator channel 3 |
| Chân 9 | IN3- — Inverting input for comparator channel 3 |
| Chân 10 | IN3+ — Non-inverting input for comparator channel 3 |
| Chân 11 | VCC — Positive supply connection |
| Chân 12 | IN4+ — Non-inverting input for comparator channel 4 |
| Chân 13 | IN4- — Inverting input for comparator channel 4 |
| Chân 14 | OUT4 — Open-collector output for comparator channel 4 |
Ứng dụng tiêu biểu
LM239DRG4 phù hợp cho 6 Áp dụngs: Industrial Voltage Supervision, Battery-Powered Sensor Interface, Motor and Actuator Control, Window and Limit Comparison, TTL and CMOS Logic Interfacing, Legacy Equipment Maintenance.
Industrial Voltage Supervision
The LM239DRG4 is suitable for monitoring multiple industrial voltage thresholds because four differential comparator channels are integrated in one 14-pin SOIC package. Each channel can compare a sensed supply or divided signal against a reference, while its open-collector output can directly pull a relay, relay-driver input, or PLC interface low. The commercial operating range of -25°C to +85°C matches controlled equipment environments. In practice, designers should verify the common-mode input range at every measured voltage, provide a suitable output pull-up, and account for input offset when setting narrow alarm thresholds.
Được đề xuất
Battery-Powered Sensor Interface
The LM239DRG4 can convert slow-moving sensor signals into logic decisions in battery-powered monitoring equipment. Its typical 3.5 nA input bias current limits loading of high-impedance sensing nodes, and the family's typical 0.8 mA supply-current drain helps constrain continuous power demand. Four thresholds can be implemented in one package rather than requiring four separate comparators. The primary trade-off is that the open-collector outputs need pull-up resistors, whose current and switching speed should be selected to balance battery consumption against required response timing.
Được đề xuất
Motor and Actuator Control
The LM239DRG4 can serve as the threshold-detection stage in motor, actuator, and power-driver control systems. Its differential inputs accept a command signal and feedback reference, allowing each channel to detect when a control quantity crosses a defined boundary. The open-collector output is useful for driving the input of a suitable driver or interface stage rather than directly driving a high-current load. Designers should keep switching-node wiring away from the high-impedance inputs and verify the response time of 1.3 us against the required fault-detection and shutdown delay.
Được đề xuất
Window and Limit Comparison
A window comparator can use two LM239DRG4 channels to detect whether a monitored signal lies between an upper and lower limit, while the other channels monitor additional rails or conditions. The device's differential architecture permits a precision reference to be applied to one input and the scaled measured signal to the other. Hysteresis can be introduced with positive feedback to prevent output chatter near the threshold. Because four channels share one package, grounding and supply bypassing are particularly important; keep the reference path quiet and use local high-frequency bypass capacitance at pin 11.
Được đề xuất
TTL and CMOS Logic Interfacing
The LM239DRG4 open-collector outputs are compatible with TTL, MOS, and CMOS logic according to the manufacturer information, making the device useful for bridging analog decisions to digital systems. A pull-up resistor establishes the high output state, while the comparator sinks current in the low state. This arrangement also permits multiple channels to share a bus node for wired-AND behavior. When choosing the pull-up value, balance reduced low-state current against slower rise time caused by bus capacitance, and ensure the connected logic input's thresholds and leakage remain within the comparator's output-current limits.
Được đề xuất
Legacy Equipment Maintenance
LM239DRG4 is relevant to maintenance and continuity programs that must reproduce an original industrial or commercial control board containing the obsolete LM239 comparator. Its 14-pin SOIC footprint and established four-channel open-collector architecture allow a qualified replacement to be considered without changing the board outline. Before substitution, review the original schematic and verify supply polarity, input common-mode limits, differential input limits, output pull-up arrangement, and temperature requirements. Lifecycle qualification and component traceability are essential when the equipment is expected to remain in service for many years.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM239DRG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM239DR | LM239ADR | LM339D | LM339DR | LM2901HYDT |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Comparator Configuration | Quad differential comparator | Quad differential comparator | Quad differential comparator | Quad differential comparator | Quad differential comparator | Quad differential comparator |
Bảo phân biệt quan trọng
- Four comparator channels in one package (vsLM2902N/PB)
- Lower cited supply current than the pin-compatible LM2901HYDT (vsLM2901HYDT)
- Commercial temperature range differs from the cited LM2901HYDT range (vsLM2901HYDT)
- Direct LM239 family continuity (vsLM339D)
Ghi chú thiết kế
Every open-collector output needs a pull-up resistor for normal high-state operation. Size the resistor so the maximum low-state sink current remains within the comparator's output rating, while also meeting the downstream device's rise-time requirement. Multiple LM239DRG4 outputs may share a common pull-up to form a wired-AND node. Do not connect an output directly to a supply rail or assume it can source current.
Place the supply bypass capacitor close to pin 11 and the ground return to pin 4, with a short and low-inductance path between the two. Route the high-impedance differential inputs away from switching-node copper, relay wiring, and inductor fields. Input filtering can reduce noise but adds response delay, so verify that the added filtering remains compatible with the application's 1.3 us typical response time.
Operate the device only within the approved single- or dual-supply configuration and check the common-mode input range at both power-up and fault conditions. Although the differential input range extends to ±38 V, that rating does not make every input voltage valid for all supply configurations. Apply power-down protection to external signal sources that could back-power the inputs while the comparator supply is off.
Do not treat the LM239, LM339, and LM2901 family names as automatically identical in every respect. Verify operating temperature, supply voltage, input offset, response time, output current, qualification, and orderable suffix. For LM2901HYDT specifically, the cited comparison shows a -40°C minimum temperature and 2 mV offset but higher supply current than LM239DRG4, so substitution requires a functional review rather than a footprint-only decision.
Thông tin tuân thủ
The manufacturer part-details page identifies LM239DRG4 as no longer in production. A separate legacy comparison notes that LM2901HYDT deletes the G4 RoHS3 waiver; no definitive RoHS or REACH declaration for LM239DRG4 was established, so those fields remain unknown.