LM2903AQM8-13 - Dual 36V Automotive Comparator | Diodes
Артикул: LM2903AQM8-13 ✓ АктивенLM2903AQM8-13 Обзор
An analog comparator is a semiconductor that compares two input voltages and produces a digital logic state indicating which input is higher. The LM2903 belongs to the comparator hierarchy that includes general-purpose voltage comparators, differential comparators, interface ICs, and discrete semiconductors. This makes it suitable for threshold detection, signal conditioning, overvoltage monitoring, and control decisions where a simple logic output is required rather than an amplified analog voltage.
The A-grade LM2903 provides a low 1 mV input offset voltage, helping reduce errors when two closely spaced voltages must be compared. Its low output saturation voltage is 200 mV at an output current of 4 mA. The open-collector architecture allows the output transistor to be pulled up to a suitable external voltage, and low input bias current of 25 nA reduces disturbance of high-impedance sensing circuits. The device is qualified to AEC-Q100 Grade 1 for automotive applications.
The LM2903Q family operates from a single positive supply or from split supplies, with the common-mode input range including ground. Its differential input range can extend across the power-supply voltage. Two independent channels allow simultaneous or unrelated comparisons, while the common eight-pin MSOP footprint reduces board area compared with discrete single comparators. Output pull-up resistors must be added because the open-collector outputs do not source current actively.
Typical uses include automotive battery monitoring, sensor threshold detection, overvoltage and undervoltage protection, window comparators, and industrial control interfaces. In an automotive application, the device can compare a divided battery or sensor voltage against a reference and produce a logic signal suitable for a controller or protection circuit. Its AEC-Q100 Grade 1 qualification is the principal automotive distinction from the non-automotive LM2903M8-13.
When designing the circuit, account for input common-mode limits, output pull-up requirements, and the voltage difference that the input pair can withstand. Keep sensitive comparator inputs away from switching-current paths and provide a stable reference source when input offset directly affects the decision threshold. Decoupling capacitors should be placed close to the supply and ground pins according to the manufacturer's recommended application layout.
This page combines the exact package and automotive qualifications, pin and family context, practical protection applications, and a same-package comparison with the non-automotive LM2903M8-13. It highlights where the A-grade offset specification and AEC-Q100 qualification justify selection, while also showing the limits of drop-in alternatives that differ in automotive qualification.
Аналоги без доработки для LM2903AQM8-13 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LM2903AQM8-13 (тот же форм-фактор и посадочное место) — отличается по Package, Differential Input Voltage Range, Logic Compatibility, Output Type, RoHS Status.
LM2903M8-13
✅ Прямая заменаУточнить цену
Открыть даташит →LM2903AQM8-13 Максимальные параметры и электрические характеристики
| Comparator Type | Dual differential voltage comparator |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 36 V |
| Input Offset Voltage, A Grade | 1 mV maximum |
| Low Output Saturation Voltage | 200 mV at 4 mA |
| Input Bias Current | 25 nA maximum |
| Ток потребления | 0.6 mA maximum |
| Тип выхода | Open collector |
| Logic Compatibility | TTL, MOS, and CMOS compatible |
| Common-Mode Input Range | Includes ground |
| Differential Input Voltage Range | Equal to the power supply voltage |
| Automotive Qualification | AEC-Q100 Grade 1 |
| Корпус | 8-pin MSOP |
| Тип монтажа | Surface mount |
| Shipping Format | Tape and reel |
| Lead-Free Status | Totally lead-free |
| Статус RoHS | Fully RoHS compliant |
| Halogen and Antimony | Halogen and antimony free |
Руководство по цоколевке LM2903AQM8-13 в корпусе 8-pin msop
Цоколевка для LM2903AQM8-13 (корпус 8-pin msop). Этот силовой прибор имеет выводы затвора, стока и истока. Для неполяризованных корпусов обратитесь к техническому описанию производителя для точной ориентации вывода 1 и деталей посадочного места. Типичные применения включают проектирование источников питания, управление двигателями и коммутацию нагрузки.
Нет подробных данных о распиновке для LM2903AQM8-13.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
LM2903AQM8-13 подходит для 6 применениеs: Automotive Battery Threshold Monitoring, Sensor Signal Conditioning, Overvoltage and Undervoltage Protection, Industrial Control Interface, Motor and Solenoid Control, Power-Supply Fault Detection.
Automotive Battery Threshold Monitoring
LM2903AQM8-13 fits automotive battery monitoring because its dual channels can compare divided battery voltages against references, while AEC-Q100 Grade 1 qualification supports vehicle-electronics requirements. The A-grade 1 mV input offset limit improves comparison resolution compared with the 2 mV non-A class. Place the device in a protected low-voltage sensing section, add external divider resistors, and use a pull-up resistor on each open-collector output. Verify that battery transients and the selected resistor network keep every input within the comparator's specified common-mode range.
Рекомендуется
Sensor Signal Conditioning
LM2903AQM8-13 is suitable for conditioning slow sensor signals that must be converted into a digital decision. Its 25 nA input bias current reduces loading on high-impedance sensor networks, and the 1 mV A-grade offset can improve the effective switching point. The two independent channels can compare upper and lower limits independently. Use the open-collector outputs to drive a logic input through pull-up resistors, and ensure sensor outputs remain within the common-mode input range while the supply can reject system noise.
Рекомендуется
Overvoltage and Undervoltage Protection
The two independent channels of LM2903AQM8-13 support window-comparator implementations for overvoltage and undervoltage protection. Divide each monitored voltage to the comparator input range, compare the scaled signal against a stable reference, and configure separate output pull-ups. The 1 mV input offset specification helps reduce threshold error in sensitive protection circuits, while its 36 V maximum supply rating supports wider industrial battery systems. Validate divider tolerances, reference stability, input protection, and fault behavior across the complete operating envelope.
Рекомендуется
Industrial Control Interface
LM2903AQM8-13 can translate analog control signals into open-collector logic states for industrial controllers. Its wide 36 V maximum supply rating accommodates higher-voltage systems when the input network is scaled appropriately, while the common-mode input range includes ground. The output saturation specification of 200 mV at 4 mA supports reliable sinking of a pull-up logic load. Place the device near the protected sensing node, maintain a quiet ground path, and account for the additional delay and propagation characteristics shown in the manufacturer datasheet.
Рекомендуется
Motor and Solenoid Control
LM2903AQM8-13 can implement current, speed, or position thresholds by comparing conditioned feedback from a motor-control system. The open-collector outputs can interface with a controller or protection stage, and the dual-channel configuration permits two related decisions. For automotive or safety-related motor electronics, AEC-Q100 Grade 1 qualification is the key selection reason. Design the input path to withstand motor transients, use a suitable logic pull-up, and verify that the reference and switching thresholds maintain adequate margin at temperature.
Рекомендуется
Power-Supply Fault Detection
LM2903AQM8-13 can supervise a power rail by comparing a divided rail voltage against a reference and asserting an open-collector fault signal. Two channels allow separate monitoring of a main rail and a secondary rail, provided both signals satisfy the common-mode input limits. The 36 V maximum supply voltage is useful when the comparator is powered from a higher rail, but the monitored inputs still require scaling or attenuation. Select pull-up values for the required fault-logic interface and validate behavior during startup, shutdown, and overload conditions.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LM2903AQM8-13 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LM2903M8-13 |
|---|---|---|
| Brand | Diodes Incorporated | Diodes Incorporated |
| Package | 8-pin MSOP | 8-pin MSOP |
| Comparator Configuration | Dual differential comparator | Dual comparator |
| Maximum Supply Voltage | 36 V | 36 V |
| Input Offset Voltage | 1 mV maximum for A grade | 2 mV maximum for non-A grade |
| Output Type | Open collector | Open collector |
| Automotive Qualification | AEC-Q100 Grade 1 | Not identified as AEC-Q100 Grade 1 |
Ключевые отличия
- Lower A-grade input offset limit (против LM2903M8-13)
- Automotive-grade qualification (против LM2903M8-13)
- Retains the same compact package for substitution (против LM2903M8-13)
Заметки по проектированию
Do not treat the open-collector outputs as push-pull logic outputs. Each output requires an external pull-up resistor to a compatible logic supply, and the resistor must be sized so the output transistor remains within its allowable sink-current and saturation-voltage limits. The manufacturer specifies 200 mV low saturation at 4 mA, so use that operating point as a design reference and confirm the actual pull-up voltage and load current against the output-characteristic curve.
Keep the comparator input traces short and route them away from switching nodes, motor windings, high-current return paths, and other sources of coupled noise. Place the supply bypass capacitor close to the supply and ground pins, and make the ground connection follow the manufacturer's application diagram. Input dividers and reference components should be physically close to the corresponding inputs to reduce parasitic pickup and to keep the 1 mV A-grade offset meaningful in sensitive threshold circuits.
Verify the complete input and supply system against the 36 V maximum rating, including transients, automotive load dumps, industrial surges, and startup overshoot. Margin between the maximum transient and 36 V is essential because absolute-maximum limits are not operating points. The differential input range is equal to the power-supply voltage, and the common-mode range includes ground, so resistor-divider calculations must satisfy both constraints across temperature and tolerance.
Account for input offset when defining a switching threshold, rather than treating the reference and comparator inputs as perfectly equal. For the LM2903AQM8-13, the A-grade offset limit is 1 mV, compared with the 2 mV non-A grade. Include reference tolerance, resistor tolerance, input bias error, and temperature effects in the system error budget. This is especially important when selecting LM2903M8-13 as a replacement for a non-automotive design.
Информация о соответствии
According to the Diodes Incorporated LM2903AQ datasheet, the device is totally lead-free, fully RoHS compliant, halogen and antimony free, and qualified to AEC-Q100 Grade 1. Reach and conflict-minerals status are unknown.