LM324SNG - Quad Op-Amp 14-PDIP | onsemi | Single Supply
Артикул: LM324SNG ✓ АктивенLM324SNG Обзор
A quad operational amplifier is an analog IC that integrates four independent op amp circuits on one die, sharing the same supply pins while keeping inputs and outputs separate. In the amplifier hierarchy it sits as an amplifier IC > operational amplifier > general-purpose amplifier, forming the analog signal-conditioning backbone of power management, sensing, and control systems.
Key advantages of the LM324S family over standard op amps in single-supply applications include a common-mode input range that extends to the negative supply rail, which eliminates external biasing components in many designs, and outputs that can swing close to ground without a negative rail. The internally compensated amplifiers need no external frequency-compensation parts, simplifying BOM and layout.
The LM324S uses mature bipolar process technology, delivering stable, predictable behavior for low-frequency analog functions such as comparators, transducer amplifiers, DC gain blocks, and active filters. Typical parameters for the LM324 family include a gain-bandwidth product around 1 MHz and low supply current per amplifier, making it a workhorse for cost-driven designs rather than high-speed or precision applications.
Typical applications include transducer amplifier front ends in industrial sensing, DC gain blocks in power supplies and battery chargers, active RC filters in audio and control paths, and voltage comparator functions in household appliances and automotive accessories. The through-hole PDIP package suits prototyping, educational boards, and repair-driven industrial designs.
Design consideration: keep closed-loop gains modest and signal frequencies well below the gain-bandwidth limit, and provide an output pull-down resistor if you need the output to reach true ground under load.
This page adds value beyond the datasheet by synthesizing drop-in replacement options, application guidance, and sourcing information in one place.
Аналоги без доработки для LM324SNG — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LM324SNG (тот же форм-фактор и посадочное место) — отличается по Amplifier Type, Mounting Type, Gain-Bandwidth Product, Package, Input Offset Voltage.
LM324ANG
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM324N
✅ Прямая заменаУточнить цену
Открыть даташит →LM324AN
✅ Прямая заменаУточнить цену
Открыть даташит →LM2902N
✅ Прямая заменаУточнить цену
Открыть даташит →LMC660AIN
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TL074N
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LM324SNG Максимальные параметры и электрические характеристики
| Amplifier Type | General Purpose Operational Amplifier |
| Number of Circuits | 4 |
| Supply Voltage (Single) | 3 V to 32 V |
| Supply Voltage (Dual) | ±1.5 V to ±16 V |
| Common-Mode Input Range | Includes negative supply rail |
| Gain-Bandwidth Product | 1 MHz (typical, LM324 family) |
| Корпус | 14-PDIP |
| Тип монтажа | Through Hole |
| Series | LM324S / LM2902S |
Конфигурация выводов LM324SNG
| Контакт 1 | OUT1 — Output of amplifier 1 |
| Контакт 2 | IN1- — Inverting input of amplifier 1 |
| Контакт 3 | IN1+ — Non-inverting input of amplifier 1 |
| Контакт 4 | VCC — Positive supply voltage |
| Контакт 5 | IN2+ — Non-inverting input of amplifier 2 |
| Контакт 6 | IN2- — Inverting input of amplifier 2 |
| Контакт 7 | OUT2 — Output of amplifier 2 |
| Контакт 8 | OUT3 — Output of amplifier 3 |
| Контакт 9 | IN3- — Inverting input of amplifier 3 |
| Контакт 10 | IN3+ — Non-inverting input of amplifier 3 |
| Контакт 11 | VEE/GND — Negative supply or ground |
| Контакт 12 | IN4+ — Non-inverting input of amplifier 4 |
| Контакт 13 | IN4- — Inverting input of amplifier 4 |
| Контакт 14 | OUT4 — Output of amplifier 4 |
Типичное применение
LM324SNG подходит для 6 применениеs: Transducer Amplifier Front End, Power Supply Feedback and Monitoring, Active RC Filters, Household Appliance Control, Automotive Accessories, Educational and Prototype Analog Labs.
Transducer Amplifier Front End
In industrial sensing, the LM324SNG serves as a multichannel transducer amplifier: one amplifier per sensor channel (pressure, temperature, light) at low closed-loop gains of 10 to 100. Because its common-mode input range includes the negative rail, sensors referenced to ground can be read directly without biasing networks, which reduces component count and board area. The 3 V to 32 V supply range covers 5 V, 12 V, and 24 V industrial rails, letting a single design serve multiple systems. The roughly 1 MHz gain-bandwidth product comfortably handles slow physical variables, and the four amplifiers enable one package to condition a full sensor cluster, cutting cost per channel in cost-driven industrial equipment.
Рекомендуется
Power Supply Feedback and Monitoring
Linear and switching power supplies use the LM324SNG for output-voltage feedback amplification, current-limit sensing, and undervoltage/overvoltage monitoring. One package provides all four functions: an error amplifier around the reference, a differential current shunt amplifier, and two comparator-style threshold detectors. Operation from the supply's own 12 V or 24 V rail eliminates an auxiliary bias rail, and the input range to the negative rail allows ground-referenced shunt sensing on the low side. Since loop bandwidths here are far below the 1 MHz gain-bandwidth product, the internally compensated amplifiers remain stable without external compensation, which suits repairable, long-lifecycle industrial power hardware.
Рекомендуется
Active RC Filters
The LM324SNG implements Sallen-Key and multiple-feedback active filters for antialiasing, tone shaping, and noise limiting. A single PDIP-14 package realizes a complete fourth-order filter using all four amplifiers, such as two cascaded second-order low-pass sections at audio cutoff frequencies. The internally compensated design needs no external frequency-compensation parts, and the 3 V to 32 V supply range allows filtering on single-ended battery or logic rails. Keep cutoff frequencies modest relative to the approximately 1 MHz gain-bandwidth product so that Q remains accurate; at gains of one to ten and cutoffs in the tens of kilohertz, the filter response closely matches calculated values, making this a standard choice in appliance and audio conditioning stages.
Рекомендуется
Household Appliance Control
Appliance control boards use the LM324SNG for motor speed-error amplification, temperature threshold comparison, and user-interface signal conditioning on a single 12 V or 24 V rail. Its tolerance for large differential input voltages and its input range extending to the negative rail allow direct connection to ground-referenced thermistor dividers and current-sense resistors without protective biasing. The through-hole 14-PDIP package supports wave soldering and field repair, matching the service model of white-goods electronics. Because each amplifier draws modest supply current from the shared rail, a single package handles the whole analog control section, and the classic LM324 behavior keeps designs reproducible across long appliance production lifecycles.
Рекомендуется
Automotive Accessories
The onsemi datasheet lists automotive accessory applications for the LM324 family: battery-voltage supervision, indicator-lamp drivers, alternator charge monitoring, and sensor conditioning in non-safety-critical accessory circuits. The wide 3 V to 32 V supply range absorbs automotive load-dump-adjacent conditions when paired with upstream protection, and each amplifier's output can source current to drive indicator LEDs with a series resistor. Four amplifiers in one package consolidate dashboard logic, reducing component count on cost-sensitive accessory boards. For production designs, validate temperature grading and consider the automotive-qualified LM2902 family variant where AEC-grade qualification is mandated by the platform requirements.
Рекомендуется
Educational and Prototype Analog Labs
The LM324SNG's through-hole PDIP-14 package and forgiving LM324-class behavior make it a staple of breadboard labs and educational analog courses. Students can build oscillators, comparators, summing amplifiers, and filters on 0.1-inch pitch without surface-mount tooling, powered from a single 9 V battery or bench supply within the 3 V to 32 V range. Internally compensated amplifiers tolerate wiring mistakes that would destabilize uncompensated devices, and the industry-standard pinout means the same lab exercises transfer directly to TI LM324N and LM2902 devices. This ubiquity also makes the part an ideal first-choice stock item for repair benches and maker inventories.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LM324SNG — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LM324ANG | LM324N | LM2902N | LMC660AIN | TL074N |
|---|---|---|---|---|---|---|
| Package | 14-PDIP | 14-PDIP - same | 14-PDIP - same | 14-PDIP - same | 14-PDIP - same | 14-PDIP - same |
| Brand | onsemi | onsemi | Texas Instruments | STMicroelectronics | Texas Instruments | Texas Instruments |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 | 4 |
| Supply Voltage (Single) | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V (family) | 3 V to 16 V | Requires dual supply (±3.5 V to ±18 V typical) |
| Input Common-Mode Includes Negative Rail | Yes | Yes | Yes | Yes | Yes (rail-to-rail input) | No (JFET input range) |
| Gain-Bandwidth Product | 1 MHz (typical, LM324 family) | 1 MHz (typical) | 1 MHz (typical) | 1 MHz (typical) | 1.5 MHz (typical, CMOS) | 3 MHz (typical) |
| Input Offset Voltage Grading | LM324S family grade | Standard LM324 grade | Standard grade (LM324A = tighter) | LM2902 grade | CMOS grade, tighter typical | JFET grade, tighter typical |
| Input Technology | Bipolar | Bipolar | Bipolar | Bipolar | CMOS | JFET |
Ключевые отличия
- Through-hole 14-PDIP packaging for serviceable designs (против MC3403DR)
- Proven single-supply input range to the negative rail (против TL074N)
- Low-cost four-channel consolidation (против LMC660AIN)
Заметки по проектированию
The LM324 output stage cannot swing to the negative rail under load; it typically saturates a fraction of a volt above VEE/GND and exhibits crossover behavior near that point. If your circuit requires the output to reach true ground (for example, driving an ADC input at 0 V or a single-supply rectifier), add a pull-down resistor of roughly 2 kOhm to 10 kOhm from the output to ground, or select a rail-to-rail-output device. Ignoring this is the single most common LM324 design mistake in single-supply comparator and zero-referenced amplifier roles.
Keep each amplifier's closed-loop bandwidth comfortably below the approximately 1 MHz gain-bandwidth product. At a gain of 10, closed-loop bandwidth is roughly 100 kHz, so reserve the device for audio-range and DC applications. Because all four amplifiers share one die and one supply pair, ground and supply impedance couple channels; use a solid ground plane or heavy ground traces, place a 0.1 uF ceramic capacitor close to pin 4 with a 10 uF bulk capacitor nearby, and keep high-gain input traces short and away from output routing to prevent inter-channel crosstalk.
For breadboarding and prototypes, the PDIP-14 package inserts directly into 0.1-inch sockets and perfboards. For production, remember through-hole assembly adds drill cost versus a surface-mount quad such as the MC3403DR (SOIC-14 footprint) - keep LM324SNG on the BOM only where through-hole serviceability is a genuine requirement. When substituting pin-compatible parts (LM324N, LM2902N, LMC660), the socketed layout needs no changes, which makes socketing the DIP footprint a low-risk way to preserve substitution flexibility during bring-up.
Информация о соответствии
RoHS/REACH and lead-free status for the exact LM324SNG suffix were not stated in the retrieved catalog snippets; confirm on the onsemi product page material declaration. The 'G' suffix in onsemi part numbering generally denotes the RoHS-compliant, lead-bent variant of the legacy LM324N, but official declaration governs.