LM358LVIDGKR - Dual 5.5V Low-Voltage Op Amp | Texas Instruments
Артикул: LM358LVIDGKR ✓ АктивенLM358LVIDGKR Обзор
An operational amplifier is an analog signal-processing building block that amplifies the voltage difference between its inverting and non-inverting inputs. A dual device such as the LM358LVIDGKR integrates two independent, internally compensated amplifiers into one package, reducing board area and component count when two gain stages are required. In the device hierarchy, the LM358LV belongs to the operational-amplifier class within analog and linear amplifiers, which are used to condition sensor, current-sense, audio, and control signals.
The family is identified as the LM3xxLV industry-standard low-voltage operational-amplifier series, which also includes the single LM321LV and quad LM324LV configurations. Key characteristics include a 1 MHz gain bandwidth product, operation to 5.5 V, low quiescent current, and high gain bandwidth relative to the original LM358 supply ratings. The dual configuration makes the device appropriate for two-amplifier signal chains, including transducer amplifiers, active filters, comparator-style threshold circuits, and low-frequency audio stages.
The LM358LV architecture provides the basic building blocks required for general-purpose analog design: two amplifiers, internal compensation, and common supply pins. Because the device is optimized for low-voltage systems, its operating region is centered on 3.3 V and 5 V rails rather than the plus or minus 15 V rails associated with the original LM358 family. Its 1 MHz bandwidth suits low-frequency and moderate-frequency conditioning rather than high-speed video or RF signal chains.
Typical uses include low-cost sensor interfaces, battery-powered measurement circuits, audio preamplifier stages, active filtering, and analog control loops. A single IC can implement a two-stage amplifier, a transimpedance amplifier followed by a gain stage, or separate inverting and non-inverting channels. The small VSSOP package also supports compact industrial and consumer control boards where a through-hole dual op amp would be unnecessarily large.
When laying out the circuit, keep feedback resistors and compensation capacitors close to the amplifier pins, and route the two channels to reduce differential crosstalk where they process unrelated signals. Confirm the required output-voltage swing, input-common-mode range, capacitive-load behavior, and supply current for the selected operating condition using the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins to suppress high-frequency supply noise.
This page consolidates the verified device identification, package information, technical characteristics, pin assignment, drop-in candidates, and application-level design guidance. It also provides a parameter comparison for selecting among same-footprint alternatives and highlights the practical trade-offs involved when replacing a general-purpose amplifier with a rail-to-rail or low-power device.
Аналоги без доработки для LM358LVIDGKR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LM358LVIDGKR (тот же форм-фактор и посадочное место).
LMV358IDGKR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TLV9002IDGKR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MCP6002IDGKR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
OPA2192IDGKR
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM358LVIDGKR Максимальные параметры и электрические характеристики
| Характеристики отсутствуют |
Конфигурация выводов LM358LVIDGKR
| Контакт 1 | OUTA — Amplifier A output |
| Контакт 2 | INA- — Amplifier A inverting input |
| Контакт 3 | INA+ — Amplifier A non-inverting input |
| Контакт 4 | V- — Negative supply or ground connection |
| Контакт 5 | INB+ — Amplifier B non-inverting input |
| Контакт 6 | INB- — Amplifier B inverting input |
| Контакт 7 | OUTB — Amplifier B output |
| Контакт 8 | V+ — Positive supply connection |
Типичное применение
LM358LVIDGKR подходит для 6 применениеs: Low-Voltage Sensor Signal Conditioning, Battery-Powered Instrumentation, Active Audio Filters, Current and Voltage Monitoring, Control and Threshold Amplification, Industrial Interface Buffering.
Low-Voltage Sensor Signal Conditioning
The LM358LVIDGKR fits two-stage conditioning for resistive sensors, thermistors, and low-level analog sensors running from a 3.3 V or 5 V rail. Its 1 MHz gain bandwidth provides more bandwidth than many slow sensor signals require, while the dual amplifier can implement an instrumentation-style chain in a single 8-VSSOP package. Place the amplifier inputs over a quiet ground region and keep the high-gain feedback resistors close to the pins to limit parasitic coupling. Confirm that the sensor output remains within the input common-mode range at the chosen supply voltage, and verify the output swing before designing for near-rail inputs.
Рекомендуется
Battery-Powered Instrumentation
The LM358LVIDGKR suits portable measurement equipment operating from 2.5 V to 5.5 V because the LM358LV family targets low-voltage systems and combines two amplifiers in one compact VSSOP package. A dual implementation can provide a low-noise input stage and a following gain or filtering stage without adding a second package. The 1 MHz gain bandwidth supports moderate-bandwidth sensor signals while leaving useful margin above slow thermistor, pressure, and chemical-sensor bandwidths. Verify the quiescent current for the expected channel activity, and use separate analog and digital return paths to keep switching converter noise away from the amplifier inputs.
Рекомендуется
Active Audio Filters
The LM358LVIDGKR can implement first- or second-order active audio filters because each internally compensated amplifier provides a 1 MHz gain bandwidth product, far above the passbands of typical baseband audio systems. Two amplifiers in the DGK VSSOP package allow a Sallen-Key or multiple-feedback filter and an additional gain stage in one device. Keep resistor and capacitor loops compact around the relevant pins, and separate the two channels if they carry independent audio paths. Validate maximum output amplitude at the intended supply voltage because the available headroom is smaller than that of a plus or minus 15 V LM358 implementation.
Рекомендуется
Current and Voltage Monitoring
The LM358LVIDGKR is appropriate for general-purpose current or voltage monitoring when the measured signal stays inside the input common-mode range. One channel can amplify a shunt voltage while the other provides gain, buffering, or threshold amplification for a downstream controller. The 1 MHz bandwidth supports fast enough response for many power-monitoring loops without introducing the complexity of a high-speed amplifier. Place the shunt amplifier close to the sensing element, use Kelvin routing where practical, and keep high-current switching nodes away from the high-impedance input and feedback components.
Рекомендуется
Control and Threshold Amplification
The LM358LVIDGKR can amplify control-loop error signals and build threshold detectors around low-voltage sensors. Its two amplifiers allow an error amplifier and a comparator-like threshold stage to share one package, reducing board area in compact control systems. The 1 MHz bandwidth is more than adequate for slow thermal, fan-speed, motor-current, and process-control loops. Check the common-mode range and output swing at the chosen supply, and add hysteresis where noise at the threshold could cause repeated switching. The device is better suited to moderate-frequency regulation than to high-speed control loops requiring wider bandwidth.
Рекомендуется
Industrial Interface Buffering
The LM358LVIDGKR works as a general-purpose interface buffer between low-voltage sensors, analog switches, and a higher-level converter on industrial control boards. Two buffered inputs or outputs can be handled in one 8-VSSOP package, which simplifies assembly where board area is constrained. The LM358LV supply range supports 3.3 V and 5 V systems, and its 1 MHz bandwidth supports many industrial interface signals that do not require high-speed differential processing. Keep sensitive analog traces away from relay drivers, power switches, and digital timing nets, and provide local bypass capacitance at the supply pins for predictable transient response.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LM358LVIDGKR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LMV358IDGKR | TLV9002IDGKR | MCP6002IDGKR | OPA2192IDGKR |
|---|---|---|---|---|---|
| Package | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Microchip Technology | Texas Instruments |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 |
| Gain Bandwidth Product | 1 MHz | 1 MHz | 1 MHz | 1 MHz | 10 MHz |
| Maximum Supply Voltage | 5.5 V | 5.5 V | 5.5 V | 5.5 V | 36 V |
| Amplifier Type | General Purpose | General Purpose, Rail-to-Rail Input | General Purpose, Rail-to-Rail Input | General Purpose, Rail-to-Rail Input | Precision |
Ключевые отличия
- General-purpose low-voltage operation in a compact dual package (против OPA2192IDGKR)
- Lower-voltage supply ceiling than the precision alternative (против OPA2192IDGKR)
- Same-package rail-to-rail upgrade option (против LMV358IDGKR)
- Direct 1 MHz bandwidth class across general-purpose alternatives (против MCP6002IDGKR)
Заметки по проектированию
Place the supply-bypass capacitor directly across pins 4 and 8 of the LM358LVIDGKR, with a short ground return that does not share a narrow path with the amplifier outputs. Keep the feedback resistors, gain-setting resistors, and compensation capacitors close to their associated pins to minimize parasitic capacitance and feedback-loop instability. In dual-channel layouts, route the two channels separately when they carry unrelated signals, and provide a quiet analog ground region beneath the feedback networks.
Do not assume that any same-package dual amplifier is electrically interchangeable with the LM358LVIDGKR. The LMV358IDGKR, TLV9002IDGKR, and MCP6002IDGKR use rail-to-rail input architectures whose bias current and common-mode behavior differ from the LM358LV. Recheck the input bias network, maximum input voltage, output swing, capacitive-load behavior, and quiescent current. A PCB footprint match removes only the mechanical obstacle; it does not remove the circuit-level verification requirement.
For low-level sensor inputs, use short traces, guard routing where appropriate, and a single low-impedance analog-ground reference. Keep switching-node copper, relay-driver outputs, and high-current return paths away from the non-inverting inputs because their leakage can create errors larger than the intended sensor signal. If both channels amplify related signals, add physical separation between input networks to limit capacitive crosstalk, and test the assembled board with the sensor source disconnected before adding additional filtering.
Информация о соответствии
No RoHS, REACH, halogen-free, or conflict-minerals declarations were identified for this ordering code. The LM358LV is a general-purpose analog amplifier rather than an automotive-qualified AEC-Q100 product.