LM393BIDGKR - Dual 38V Open-Collector Comparator | Texas Instruments
Артикул: LM393BIDGKR ✓ АктивенLM393BIDGKR Обзор
A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM393B belongs to the dual-comparator hierarchy, combining two differential comparator channels in one integrated circuit. It is commonly used in the wider category of signal-conditioning and threshold-detection ICs, where a sensed voltage is compared against a reference or control signal.
Key characteristics include a low supply current of 200 uA per comparator, a response time of 1 us, and a 2 kV human-body-model ESD rating. The common-mode input range includes ground, while the differential input range equals the maximum-rated supply voltage of 38 V. These features support robust sensing in industrial, communication, instrumentation, and embedded systems where the input may exceed conventional logic levels.
The B-version architecture retains the familiar LM393 dual-open-collector interface while improving offset voltage, supply-current consumption, input bias current, propagation delay, and ESD ruggedness. Dedicated input clamps strengthen the inputs against electrostatic discharge. Each output can sink logic-level current while remaining in a high-impedance state when inactive, allowing multiple open-collector nodes to share a pull-up network when the electrical design permits it.
Typical uses include overvoltage and undervoltage detection, window comparators, temperature-threshold circuits, sensor signal conditioning, relay or solenoid activation, and battery-powered monitoring. The low 200 uA per-comparator supply demand is particularly useful in systems where the comparator must remain active continuously without dominating the standby power budget.
Design with the open-collector output in mind: every output requires a pull-up resistor to the appropriate logic supply. Place input, output, and decoupling connections to minimize parasitic pickup, and account for input offset and bias currents when working near the switching threshold. Keep the common-mode and differential inputs within their specified operating limits.
This product page combines the LM393BIDGKR electrical characteristics, package and pin assignment, same-package alternatives, and practical application guidance. It supports faster engineering decisions by connecting the comparator’s offset, bias current, response time, ESD rating, and supply capability directly to common circuit-design requirements.
Аналоги без доработки для LM393BIDGKR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
LM2903BIDGKR
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM393AIDGKR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LM393VIDGKR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LM2903AIDGKR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LM2903VIDGKR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LM393BIDGKR Максимальные параметры и электрические характеристики
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Тип выхода | Open-collector |
| Maximum Supply Rating | 38 V |
| Supply Current per Comparator | 200 uA |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| Response Time | 1 us |
| ESD Rating, Human Body Model | 2 kV |
| Common-Mode Input Range | Includes ground |
| Differential Input Range | Up to 38 V |
| Logic Compatibility | TTL, MOS, and CMOS |
| Диапазон рабочих температур | -40 C to +85 C |
| Корпус | 8-pin VSSOP (DGK) |
| Число выводов | 8 pins |
| Тип монтажа | Surface mount |
| Grade | Commercial grade |
Конфигурация выводов LM393BIDGKR
| Контакт 1 | OUT1 — Open-collector output for comparator channel 1 |
| Контакт 2 | IN1- — Inverting input for comparator channel 1 |
| Контакт 3 | IN1+ — Non-inverting input for comparator channel 1 |
| Контакт 4 | GND — Ground connection |
| Контакт 5 | IN2+ — Non-inverting input for comparator channel 2 |
| Контакт 6 | IN2- — Inverting input for comparator channel 2 |
| Контакт 7 | OUT2 — Open-collector output for comparator channel 2 |
| Контакт 8 | VCC — Positive supply connection |
Типичное применение
LM393BIDGKR подходит для 6 применениеs: Industrial Overvoltage Detection, Battery Voltage Monitoring, Temperature Threshold Detection, Sensor Signal Conditioning, Window and Fault Monitoring, Power-Sequencing Control.
Industrial Overvoltage Detection
The LM393BIDGKR fits industrial overvoltage detection because its differential inputs can operate across the maximum-rated 38 V range while the input offset is only 0.37 mV. A resistive divider scales the monitored voltage into the comparison range, and the open-collector output changes state when the threshold is exceeded. Add the required pull-up resistor to the control-logic rail and keep the sensing network away from switching nodes. The 2 kV HBM ESD rating and dedicated input clamps improve robustness, although normal component ratings do not replace external surge protection. The dual-channel configuration can monitor positive and negative rails independently when each divider uses a suitable reference.
Рекомендуется
Battery Voltage Monitoring
The LM393BIDGKR is appropriate for battery-voltage monitoring because each comparator consumes only 200 uA and has a low input bias current of 3.5 nA. The divider can sense a battery rail that exceeds the logic supply, while the open-collector output indicates charge or discharge thresholds through a pull-up. This arrangement avoids powering a microcontroller continuously for a simple threshold decision. Pull-up current remains part of the standing load and must be included in the battery budget. The 0.37 mV offset supports precise threshold placement, while the 38 V maximum rating accommodates higher-energy systems when all pins remain within their operating limits.
Рекомендуется
Temperature Threshold Detection
The LM393BIDGKR can implement a compact temperature-alarm threshold around a resistive sensor and reference. Its 3.5 nA input bias current creates little error with a suitably high-value sensor network, while the 0.37 mV offset improves the switching-point repeatability. One open-collector channel can indicate an upper temperature limit, and the second can indicate a lower limit for an independent window alarm. Pull both outputs up to the system logic rail and use Schmitt-action hysteresis or a small positive-feedback network if chatter appears near the threshold. The 1 us response time is ample for many thermal systems and allows rapid shutdown signaling.
Рекомендуется
Sensor Signal Conditioning
The LM393BIDGKR suits sensor signal conditioning when a low-level analog signal must be converted into a logic decision. Place the sensor output on the non-inverting input and a stable reference on the inverting input, or reverse the arrangement for an opposite output polarity. The 0.37 mV offset and 3.5 nA input bias current are useful when preserving a small sensor signal at the decision point. Its dual open-collector outputs can support digital alarm and enable functions without adding another comparator package. Keep the input traces short, use a stable reference, and add a pull-up resistor with a rise time appropriate for the receiving logic.
Рекомендуется
Window and Fault Monitoring
The two channels of the LM393BIDGKR can create a window fault detector by comparing the monitored signal against upper and lower thresholds. One open-collector output reports operation above the upper limit, while the other reports operation below the lower limit. This arrangement is useful in power rails, communication links, and actuator feedback systems where both overvoltage and undervoltage must be reported. The open-collector outputs permit wired signaling when their logic states are designed appropriately. A 1 us response time supports fast fault detection, and the 38 V rating offers useful voltage-range headroom. External filtering and hysteresis remain important when the monitored signal contains noise.
Рекомендуется
Power-Sequencing Control
The LM393BIDGKR can support simple power-sequencing or power-good logic by comparing divided supply voltages with references. Its open-collector output can pull down an enable node or report a rail state, and the second channel can monitor another supply independently. The 200 uA supply current per comparator limits overhead in continuously monitored systems, while the 38 V rating is useful for industrial supply buses. Use a pull-up to the destination logic rail and account for the fact that an open-collector output cannot actively drive a high voltage. The comparator does not provide complete sequencing control by itself, so system logic must define the permitted order and fault response.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LM393BIDGKR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LM2903BIDGKR | LM393AIDGKR | LM393VIDGKR | LM2903AIDGKR | LM2903VIDGKR |
|---|---|---|---|---|---|---|
| Package | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Count | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
Ключевые отличия
- Lower input offset than earlier LM393-family revisions (против LM393AIDGKR)
- Lower input bias current for high-impedance sensing (против LM393AIDGKR)
- Faster switching response (против LM393AIDGKR)
- Improved electrostatic-discharge robustness (против LM393VIDGKR)
Заметки по проектированию
Each open-collector output requires an external pull-up resistor. Select the resistor from the required output rise time, input capacitance, receiver leakage, and allowable sink current rather than applying one value to every interface. Keep the pull-up connection short and use a voltage compatible with the receiving TTL, MOS, or CMOS logic. Leaving an output without a pull-up leaves its logic level undefined when the transistor is off.
The specified supply current is 200 uA per comparator. For a two-channel device, the nominal comparator supply contribution is 400 uA before input bias current, output pull-up current, and other circuit losses. In battery-powered designs, calculate the continuous current through each pull-up because an open-collector output can remain continuously off. Use the complete power budget rather than treating the stated comparator current as the entire circuit demand.
Route the non-inverting and inverting input traces as a compact differential pair and keep them away from switching-regulator power nodes, relay coils, and high-current outputs. Place the input-sensing network close to the comparator to reduce leakage from PCB contamination and adjacent circuitry. The input bias current is only 3.5 nA, so very high source impedances can still shift the effective threshold; verify the resistor and sensor impedances when the threshold must remain precise.
Do not assume the 38 V maximum rating can be applied arbitrarily to either input. The differential input range may extend to the maximum-rated supply voltage, while the common-mode range includes ground but does not extend automatically to every positive voltage. Check both input pins against the manufacturer’s absolute-maximum and operating-limit tables. Add input attenuation or clamping when an external fault condition can exceed the allowed range.
A comparator can chatter when its input voltage crosses the threshold slowly or contains noise. Add controlled positive feedback for hysteresis where the circuit permits it, or place a small RC filter at the input to reject high-frequency noise. The 1 us response time is suitable for many threshold systems, but filtering adds delay and changes the switching threshold. Evaluate both effects before fixing the time constant.
Информация о соответствии
The device is identified as commercial grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the cited product information.