LM393PWR - Dual Comparator Open-Collector TSSOP-8 | TI
Артикул: LM393PWR ✓ АктивенLM393PWR Обзор
A voltage comparator is a circuit that compares two analog input voltages and drives its output to indicate which input is higher. As a member of the linear comparator family within the broader analog signal-conditioning hierarchy, the LM393 belongs to the general-purpose comparator class that preceded high-speed and precision comparators. Its open-collector outputs allow wire-AND connections and simple interfacing to logic levels and higher-voltage rails, which is why dual comparators like the LM393 remain among the most widely used analog building blocks in power management and sensing subsystems.
Key features include two independent precision voltage comparators specifically designed to operate from a single power supply over a wide range of voltages, an offset voltage specification as low as 2.0mV max for the two comparators, and a quiescent current that is independent of the supply voltage. The outputs are open-collector stages that can sink current while being pulled up externally to any voltage within the supply range, enabling flexible logic-level translation.
Architecturally, each comparator uses a differential PNP input stage whose input common-mode range extends to ground (and slightly below), allowing sensing of signals referenced at or near 0V on a single rail. The open-collector output sinks current when the inverting input exceeds the non-inverting input; with an external pull-up resistor it delivers a clean, fast digital transition. Propagation delay is in the microsecond range, appropriate for monitoring, level detection, and slow control loops rather than high-speed clocking.
Typical applications include limit comparators and window detectors, battery-powered voltage monitors and low-battery warnings, sensor threshold detection, and PWM/motor-control feedback circuits in industrial and consumer products.
Design consideration: always include an external pull-up resistor on each open-collector output sized for the required sink current, and provide hysteresis with positive feedback when comparing slowly changing signals to prevent output chatter near the threshold.
This page synthesizes drop-in alternatives, parametric comparisons, and practical design notes beyond what the manufacturer datasheet alone provides.
Аналоги без доработки для LM393PWR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LM393PWR (тот же форм-фактор и посадочное место) — отличается по Comparator Type, Output Type, Package, Supply Voltage Range.
LM393BPWR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LM2903BPWR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LM393LVPWR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LM393PWRG3
✅ Прямая заменаУточнить цену
Открыть даташит →LM393PWR Максимальные параметры и электрические характеристики
| Number of Channels | 2 |
| Comparator Type | General purpose, differential |
| Тип выхода | Open-collector (CMOS-compatible with pull-up) |
| Supply Voltage Range | Up to 36 V (single supply) |
| Supply Voltage Range (Dual) | +/-18 V |
| Maximum Input Offset Voltage | 2 mV |
| Input Common-Mode Range | Includes ground (V-) on single supply |
| Корпус | 8-TSSOP (PW) |
| Тип монтажа | Surface Mount |
| Type | Standard (general purpose) |
| Input Stage | PNP differential |
Конфигурация выводов LM393PWR
| Контакт 1 | OUT A — Output of comparator A (open-collector, requires pull-up) |
| Контакт 2 | IN A- — Inverting input of comparator A |
| Контакт 3 | IN A+ — Non-inverting input of comparator A |
| Контакт 4 | GND — Ground / V- supply |
| Контакт 5 | IN B+ — Non-inverting input of comparator B |
| Контакт 6 | IN B- — Inverting input of comparator B |
| Контакт 7 | OUT B — Output of comparator B (open-collector, requires pull-up) |
| Контакт 8 | VCC — Positive supply, up to 36V single supply |
Типичное применение
LM393PWR подходит для 6 применениеs: Voltage Monitoring and Low-Battery Warning, Limit Comparator and Window Detection, Sensor Threshold Detection, PWM and Motor Control Feedback, Power-Supply Supervision and UVLO, Level Shifting and Logic Interfacing.
Voltage Monitoring and Low-Battery Warning
The LM393PWR fits battery monitor circuits because its quiescent current is independent of the supply voltage and its PNP inputs sense signals down to ground, so undervoltage thresholds can be set without level shifting. A resistor divider from the battery feeds the inverting input, a reference divider sets the trip point, and the open-collector output pulls low to signal a warning. Typical designs trip at a fixed fraction of the battery voltage; hysteresis via positive feedback prevents flicker near the threshold. The wide 36V rating lets the same layout monitor multi-cell stacks, and the second comparator can implement a complementary overvoltage flag in the same package.
Рекомендуется
Limit Comparator and Window Detection
Both LM393PWR comparators can be paired into a window detector: one trips when the input rises above the upper limit, the other when it falls below the lower limit. Because the outputs are open-collector, they can be wired directly together in a wire-AND configuration with a single pull-up resistor - no external OR logic is required. This suits power-supply rail supervision where VOUT must stay within specified bounds, and industrial interlock monitoring. The 2mV max offset voltage provides adequate threshold accuracy for percent-level windows, and the TSSOP-8 footprint keeps the supervisor section compact on crowded boards.
Рекомендуется
Sensor Threshold Detection
The LM393PWR interfaces directly to ground-referenced sensors such as thermistors, LDRs, photodiode loads and strain-gauge bridges. The input common-mode range that includes ground on a single supply means small sensor signals at low potential can be compared without biasing tricks, and the differential inputs accommodate either polarity of trip logic. One comparator handles the analog threshold while the second can latch an alarm state or drive a status LED through its open-collector output. Because the device draws microamp-level quiescent current per comparator, it remains practical in battery-operated IoT sensor nodes that must spend most of their life in standby.
Рекомендуется
PWM and Motor Control Feedback
In PWM motor controllers, the LM393PWR compares a sawtooth or triangle carrier against an error-amplifier output to generate the PWM waveform, or compares the shunt voltage against a current-limit reference to gate the drive stage. The open-collector output integrates naturally into transistor drive chains and can pull a latch or shutdown pin low directly. Its microsecond-class response suits motor control loops that operate in the kHz switching range rather than MHz-class converters. The dual channels let one comparator perform PWM generation and the other implement independent overcurrent or overtemperature protection in the same TSSOP-8 package.
Рекомендуется
Power-Supply Supervision and UVLO
The LM393PWR implements undervoltage lockout by comparing a divided-down supply rail against a reference; the open-collector output then holds the downstream controller in reset until the rail is valid. Its 36V single-supply rating allows direct supervision of industrial 24V buses without pre-regulation, and the ground-including input range supports low-side shunt sensing for fault detection. Quiescent current independent of supply voltage keeps standby losses low in always-on infrastructure equipment. Because the part is second-sourced by ROHM under the identical MPN and package, supervisor sections can be dual-sourced at the BOM level without redesign.
Рекомендуется
Level Shifting and Logic Interfacing
The open-collector output of the LM393PWR makes it a simple comparator-based level shifter: the output pull-up resistor can be tied to any logic rail within the supply range, so a circuit powered at 12V or 24V can interface cleanly to a 3.3V or 5V microcontroller input. This is useful when crossing voltage domains in mixed industrial systems, intercom circuits, and alarm panels. Adding hysteresis via positive feedback cleans up noisy crossings, and the second comparator can invert logic polarity or build a Schmitt-trigger stage. The TSSOP-8 footprint allows several channels per square centimeter on interface boards.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LM393PWR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LM393BPWR | LM2903BPWR | LM393LVPWR | LM393PWR (ROHM) |
|---|---|---|---|---|---|
| Package | 8-TSSOP (PW) | 8-TSSOP (PW) - same | 8-TSSOP (PW) - same | 8-TSSOP (PW) - same | 8-TSSOP (PW) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | ROHM Semiconductor |
| Number of Comparators | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open-collector | Open-collector | Open-collector | Open-drain | Open-collector |
| Supply Voltage Range | Up to 36 V | Higher capability than LM393 | Higher capability than LM393 | Lower voltage range | +/-18 V / 36 V |
| Pin Compatibility | Reference (TSSOP-8) | Pin-to-pin compatible | Pin-to-pin compatible | Pin-for-pin per TI | Pin-to-pin compatible (industry standard) |
Ключевые отличия
- Industry-standard second sourcing (против LM393PWR (ROHM Semiconductor))
- Wide 36V single-supply range with ground-including inputs (против LM393LVPWR)
- Upgrade path with measurable spec improvements (против LM393BPWR)
Заметки по проектированию
Every open-collector output must have an external pull-up resistor to a defined rail; choose 10kohm as a general default, lowering to 1kohm-4.7kohm when faster rise times or longer trace drive is required. Route the pull-up to the correct logic rail - not necessarily VCC - to achieve level shifting. Keep input traces short and away from switching nodes; high-impedance comparator inputs readily pick up capacitive coupling from PWM or clock nets, which manifests as false trips.
Without hysteresis, the LM393 output chatters when the input crosses the threshold slowly or when the signal carries noise, since the comparator oscillates through its linear region. Add positive feedback (resistor from output to the non-inverting input, typically in the 100kohm range) sized so the trip-to-release gap exceeds the expected noise amplitude. Remember the effective feedback amplitude differs on output-high (pull-up divider) versus output-low (hard ground) states, so calculate hysteresis for both output states separately.
The LM393 quiescent current is independent of supply voltage, but total current consumption equals quiescent current plus pull-up resistor current whenever an output is low. For battery applications, select larger pull-up values (47kohm-100kohm) if edge speed permits, and place the trip logic so outputs idle high. Decouple VCC with a 100nF ceramic capacitor placed close to pin 8; during output transitions the device draws dynamic current that can couple rail noise into the other comparator in the same package.
The PNP input stage allows common-mode input down to ground, but the inputs must remain within the valid common-mode range at the top end (approximately VCC minus 1.5V per classic LM393 family behavior). Exceeding the common-mode range can invert comparator response unexpectedly. When comparing signals that approach the upper rail, divide them down first or choose the LM393LV/LM393B with wider input-range specifications for low-voltage designs.
Информация о соответствии
Compliance status not stated in the retrieved sources; consult the TI LM393 product page at ti.com/product/LM393 for current RoHS/REACH declarations.