Texas Instruments

LM393PWR - Dual Comparator Open-Collector TSSOP-8 | TI

MPN: LM393PWR ✓ فعال
Up to 36 V (single supply) Vdss 8-TSSOP (PW) Package
حداقل سفارش: 1 |

LM393PWR نمای کلی

The Texas Instruments LM393PWR is a dual differential voltage comparator with an open-collector output stage, housed in an 8-pin TSSOP (PW) surface-mount package. It operates from a single supply over a wide voltage range up to 36V, with a maximum input offset voltage of 2mV, and each of its two independent precision comparators draws only microamp-level supply current.

A voltage comparator is a circuit that compares two analog input voltages and drives its output to indicate which input is higher. As a member of the linear comparator family within the broader analog signal-conditioning hierarchy, the LM393 belongs to the general-purpose comparator class that preceded high-speed and precision comparators. Its open-collector outputs allow wire-AND connections and simple interfacing to logic levels and higher-voltage rails, which is why dual comparators like the LM393 remain among the most widely used analog building blocks in power management and sensing subsystems.

Key features include two independent precision voltage comparators specifically designed to operate from a single power supply over a wide range of voltages, an offset voltage specification as low as 2.0mV max for the two comparators, and a quiescent current that is independent of the supply voltage. The outputs are open-collector stages that can sink current while being pulled up externally to any voltage within the supply range, enabling flexible logic-level translation.

Architecturally, each comparator uses a differential PNP input stage whose input common-mode range extends to ground (and slightly below), allowing sensing of signals referenced at or near 0V on a single rail. The open-collector output sinks current when the inverting input exceeds the non-inverting input; with an external pull-up resistor it delivers a clean, fast digital transition. Propagation delay is in the microsecond range, appropriate for monitoring, level detection, and slow control loops rather than high-speed clocking.

Typical applications include limit comparators and window detectors, battery-powered voltage monitors and low-battery warnings, sensor threshold detection, and PWM/motor-control feedback circuits in industrial and consumer products.

Design consideration: always include an external pull-up resistor on each open-collector output sized for the required sink current, and provide hysteresis with positive feedback when comparing slowly changing signals to prevent output chatter near the threshold.

This page synthesizes drop-in alternatives, parametric comparisons, and practical design notes beyond what the manufacturer datasheet alone provides.

جایگزین‌های drop-in برای LM393PWR — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای LM393PWR (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Comparator Type, Output Type, Package, Supply Voltage Range.

Texas Instruments
Comparator Type: General-purpose differential comparator
Output Type: Open-collector
Package: 8-pin TSSOP
مقایسه با LM393PWR →

LM393BPWR

✅ جایگزین مستقیم
📦 8-TSSOP (PW)
next-generation B-version: lower offset voltage, lower supply and bias current, faster propagation delay, 2kV ESD clamps; same TSSOP-8 pinout

📋 جایگزین مرجع (خارج از کاتالوگ)

LM2903BPWR

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-TSSOP (PW)
B-version family member with extended/industrial temperature grade; same pinout and package, otherwise spec-improved like LM393B

📋 جایگزین مرجع (خارج از کاتالوگ)

LM393LVPWR

✅ جایگزین مستقیم
📦 8-TSSOP (PW)
low-voltage family variant, pin-for-pin per TI comparison; lower supply voltage range, lower power, lower offset, faster speed

📋 جایگزین مرجع (خارج از کاتالوگ)

LM393PWRG3

✅ جایگزین مستقیم
Texas Instruments
📦 8-TSSOP (PW)
General-purpose differential comparator · 2 · 2 V to 36 V · ±1 V to ±18 V · Open-collector · Differential · Rail-to-rail · 2.5 mA

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

LM393PWR حداکثر مقادیر مجاز و مشخصات الکتریکی

Number of Channels 2
Comparator Type General purpose, differential
نوع خروجی Open-collector (CMOS-compatible with pull-up)
Supply Voltage Range Up to 36 V (single supply)
Supply Voltage Range (Dual) +/-18 V
Maximum Input Offset Voltage 2 mV
Input Common-Mode Range Includes ground (V-) on single supply
بسته‌بندی 8-TSSOP (PW)
نوع نصب Surface Mount
Type Standard (general purpose)
Input Stage PNP differential

پیکربندی پین LM393PWR

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
پین 1 OUT A — Output of comparator A (open-collector, requires pull-up)
پین 2 IN A- — Inverting input of comparator A
پین 3 IN A+ — Non-inverting input of comparator A
پین 4 GND — Ground / V- supply
پین 5 IN B+ — Non-inverting input of comparator B
پین 6 IN B- — Inverting input of comparator B
پین 7 OUT B — Output of comparator B (open-collector, requires pull-up)
پین 8 VCC — Positive supply, up to 36V single supply

کاربردهای معمول

LM393PWR مناسب است برای 6 کاربردs: Voltage Monitoring and Low-Battery Warning, Limit Comparator and Window Detection, Sensor Threshold Detection, PWM and Motor Control Feedback, Power-Supply Supervision and UVLO, Level Shifting and Logic Interfacing.

⚡

Voltage Monitoring and Low-Battery Warning

The LM393PWR fits battery monitor circuits because its quiescent current is independent of the supply voltage and its PNP inputs sense signals down to ground, so undervoltage thresholds can be set without level shifting. A resistor divider from the battery feeds the inverting input, a reference divider sets the trip point, and the open-collector output pulls low to signal a warning. Typical designs trip at a fixed fraction of the battery voltage; hysteresis via positive feedback prevents flicker near the threshold. The wide 36V rating lets the same layout monitor multi-cell stacks, and the second comparator can implement a complementary overvoltage flag in the same package.

🔧

Limit Comparator and Window Detection

Both LM393PWR comparators can be paired into a window detector: one trips when the input rises above the upper limit, the other when it falls below the lower limit. Because the outputs are open-collector, they can be wired directly together in a wire-AND configuration with a single pull-up resistor - no external OR logic is required. This suits power-supply rail supervision where VOUT must stay within specified bounds, and industrial interlock monitoring. The 2mV max offset voltage provides adequate threshold accuracy for percent-level windows, and the TSSOP-8 footprint keeps the supervisor section compact on crowded boards.

🧩

Sensor Threshold Detection

The LM393PWR interfaces directly to ground-referenced sensors such as thermistors, LDRs, photodiode loads and strain-gauge bridges. The input common-mode range that includes ground on a single supply means small sensor signals at low potential can be compared without biasing tricks, and the differential inputs accommodate either polarity of trip logic. One comparator handles the analog threshold while the second can latch an alarm state or drive a status LED through its open-collector output. Because the device draws microamp-level quiescent current per comparator, it remains practical in battery-operated IoT sensor nodes that must spend most of their life in standby.

🏭

PWM and Motor Control Feedback

In PWM motor controllers, the LM393PWR compares a sawtooth or triangle carrier against an error-amplifier output to generate the PWM waveform, or compares the shunt voltage against a current-limit reference to gate the drive stage. The open-collector output integrates naturally into transistor drive chains and can pull a latch or shutdown pin low directly. Its microsecond-class response suits motor control loops that operate in the kHz switching range rather than MHz-class converters. The dual channels let one comparator perform PWM generation and the other implement independent overcurrent or overtemperature protection in the same TSSOP-8 package.

🖥️

Power-Supply Supervision and UVLO

The LM393PWR implements undervoltage lockout by comparing a divided-down supply rail against a reference; the open-collector output then holds the downstream controller in reset until the rail is valid. Its 36V single-supply rating allows direct supervision of industrial 24V buses without pre-regulation, and the ground-including input range supports low-side shunt sensing for fault detection. Quiescent current independent of supply voltage keeps standby losses low in always-on infrastructure equipment. Because the part is second-sourced by ROHM under the identical MPN and package, supervisor sections can be dual-sourced at the BOM level without redesign.

🌐

Level Shifting and Logic Interfacing

The open-collector output of the LM393PWR makes it a simple comparator-based level shifter: the output pull-up resistor can be tied to any logic rail within the supply range, so a circuit powered at 12V or 24V can interface cleanly to a 3.3V or 5V microcontroller input. This is useful when crossing voltage domains in mixed industrial systems, intercom circuits, and alarm panels. Adding hysteresis via positive feedback cleans up noisy crossings, and the second comparator can invert logic polarity or build a Schmitt-trigger stage. The TSSOP-8 footprint allows several channels per square centimeter on interface boards.

خلاصه محصولات پیشنهادی

TL431 Precision voltage reference for the trip point استفاده‌شده در: Voltage Monitoring and Low-Battery Warning, Limit Comparator and Window Detection, Sensor Threshold Detection, PWM and Motor Control Feedback, Power-Supply Supervision and UVLO LM393BPWR Drop-in B-version upgrade استفاده‌شده در: Voltage Monitoring and Low-Battery Warning, Limit Comparator and Window Detection, Sensor Threshold Detection, PWM and Motor Control Feedback, Level Shifting and Logic Interfacing LM2903BPWR Industrial-grade B-version drop-in استفاده‌شده در: Power-Supply Supervision and UVLO LM393LVPWR Low-voltage pin-for-pin variant استفاده‌شده در: Level Shifting and Logic Interfacing
What is the LM393PWR and what does it do?
The LM393PWR is a Texas Instruments dual differential voltage comparator in an 8-pin TSSOP package. It contains two independent precision comparators, each comparing a differential input pair and driving an open-collector output. According to TI's LM393 product page, the device is designed to operate from a single power supply over a wide range of voltages up to 36V, with input offset voltage as low as 2.0mV max. It is used for threshold detection, voltage monitoring, and sensor interfacing.
Where can I download the LM393PWR datasheet PDF?
You can download the LM393PWR datasheet directly from the Texas Instruments product page at ti.com/product/LM393. The TI datasheet titled 'Dual Differential Comparators' covers the LM393 family including the PWR (TSSOP-8) package, with electrical characteristics, typical application circuits, and package drawings. Third-party archives such as alldatasheet.com also host the PDF, but the TI.com official copy is the authoritative and most current revision.
What is the difference between LM393 and LM393B?
The LM393B is the next-generation version of the industry-standard LM393 family. According to the TI LM393 datasheet introduction, the B-version devices feature lower offset voltage, higher supply voltage capability, lower supply current, lower input bias current, lower propagation delay, and improved 2kV ESD performance with dedicated ESD input clamps. TI states the LM393B and LM2903B can drop-in replace the LM293, LM393 and LM2903 for both 'A' and 'V' grades, so a direct upgrade path exists on the same PCB footprint.
Can LM393B replace LM393PWR?
Yes. According to Texas Instruments, the LM393B and LM2903B can drop-in replace the LM293, LM393 and LM2903 for both 'A' and 'V' grades, on the same pinout and package footprint. The LM393B offers measurably better specifications: lower offset voltage, lower supply and input bias current, faster propagation delay, and 2kV ESD ruggedness. Existing LM393PWR designs can migrate to LM393BPWR without layout changes; verify timing margins only in very fast trip-point circuits.
What is the best drop-in replacement for LM393PWR?
The best drop-in replacement for LM393PWR is the TI LM393BPWR, the next-generation B-version in the same TSSOP-8 footprint; TI explicitly states it can drop-in replace the LM393 with improved specifications including lower offset voltage and 2kV ESD protection. Other options are the LM2903BPWR (automotive/extended-grade B-version) and the LM393LVPWR (pin-for-pin, lower voltage 1.65V-5.5V family with lower power). All share the same TSSOP-8 pinout.
Is LM393PWR pin-compatible with the ROHM LM393PWR?
Yes. The ROHM Semiconductor LM393PWR is a second-source implementation of the same industry-standard LM393 dual comparator function in the same 8-TSSOP package. Distributors such as DigiKey and Mouser list both the TI and ROHM versions under the identical MPN with the same open-collector, dual general-purpose comparator description and the same +/-18V/36V ratings. Designers can interchange them, though second-source electrical details should be confirmed in the ROHM datasheet for marginal parameters.
What is the supply voltage range of the LM393?
The LM393 operates from a single power supply over a wide range of voltages, up to 36V, or from dual supplies of +/-18V. According to the TI LM393 datasheet, the device was designed specifically for single-supply operation, and its quiescent current is independent of the supply voltage. The PNP input stage allows the common-mode input range to include ground, making the part suitable for sensing signals at or near 0V in low-side monitoring circuits.
Why does the LM393 output need a pull-up resistor?
The LM393 has an open-collector output stage, which can only sink current to ground but never source current high. An external pull-up resistor is mandatory to define the output high level; the pull-up can connect to any voltage within the supply range, enabling wire-AND connections and convenient level shifting to logic rails such as 3.3V or 5V. Typical pull-up values are 1kohm to 100kohm, with 10kohm a common choice balancing speed against current draw.
How should I add hysteresis to an LM393 comparator circuit?
Add positive feedback by connecting a resistor from the LM393 output to its non-inverting input. Because the output is open-collector, the effective feedback voltage depends on the pull-up network; a common approach uses a divider from output to reference. Hysteresis eliminates output chatter when the input signal crosses the threshold slowly or carries noise. Keep feedback resistors large (100kohm range) so they do not excessively load the open-collector output or distort the trip point.
What can replace LM393PWR in a 5V system?
In a 5V-only system, pin-compatible replacements for LM393PWR include the TI LM393LVPWR, a pin-for-pin member of the LM393 family optimized for lower voltage ranges with lower power, lower offset voltage and faster speed, and the TI LM393BPWR, the next-generation B-version that drop-in replaces the classic LM393. Third-party equivalents also exist from other comparator families, but any substitute must be verified as dual, open-collector, and TSSOP-8 pin-to-pin compatible before use.
Is the LM393PWR suitable for battery-powered voltage monitoring?
Yes. The LM393PWR is a classic choice for battery-powered monitoring because its quiescent current is independent of the supply voltage and remains in the microampere range per comparator, and its PNP inputs sense voltages down to ground. Typical circuits include low-battery warnings, undervoltage lockout, and window comparators around a supervisor threshold. Its wide single-supply range up to 36V also lets one device monitor multi-cell stacks directly without front-end dividers beyond the trip network.
What are the key specifications of the LM393PWR that engineers should know?
Engineers should know these LM393PWR facts: dual differential comparator, 8-pin TSSOP (PW) package, single-supply operation up to 36V (or +/-18V dual), input offset voltage as low as 2.0mV max, open-collector outputs requiring external pull-ups, input common-mode range including ground, and quiescent current independent of supply voltage. It is an industry-standard second-sourced part, and the TI LM393B/LM2903B B-versions are drop-in upgrades with lower offset, lower current, faster response, and 2kV ESD clamps.
What is the difference between LM393 and LM393LV?
The LM393LV is TI's low-voltage member of the same family, offered pin-for-pin to the LM393 but targeting lower voltage systems. According to TI's product comparison, the LM393LV provides an alternative for lower voltage ranges with improved performance: lower power, lower offset voltage, and faster speed. Choose the classic LM393/LM393B for wide-range rails up to 36V; choose the LM393LV for 1.65V-5.5V logic-supply systems where power and speed matter more than voltage headroom.
Where can I buy LM393PWR and what is the lead time?
You can request LM393PWR pricing, stock, and lead time through the Request a Quote form on this page. The part is an active, industry-standard component listed by Texas Instruments on ti.com and stocked through major distribution channels, so lead times are typically short, but exact pricing depends on quantity and current market conditions. Standard packaging for the PWR suffix is tape and reel; state your quantity in the quote request for tiered pricing.
Does the LM393 work with inputs near ground on a single supply?
Yes. The LM393 uses a differential PNP input stage that allows the common-mode input voltage range to extend to the negative rail (ground on single-supply operation), and even slightly below it. This is a defining feature of the LM393 family compared with comparators whose inputs require headroom above the negative rail. It makes the device well suited to low-side current sensing, ground-referenced threshold detection, and battery monitor circuits without negative supplies or input level shifting.

داده‌های مرجع مهندسی برای LM393PWR — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose LM393PWR when you need a proven, second-sourceable dual comparator for wide-range rails up to 36V or +/-18V, particularly in industrial 24V supervision, battery monitors, and sensor thresholds where inputs must sense down to ground. Choose LM393BPWR for any new design or cost-effective migration: TI documents it as a drop-in replacement for the LM393 with lower offset, lower current, faster response, and 2kV ESD ruggedness on the identical TSSOP-8 footprint. Choose LM2903BPWR when extended/industrial grade qualification is required. Choose LM393LVPWR only for 5V-and-below logic-supply systems where lower power and faster response matter more than voltage headroom. All listed alternatives share the same 8-TSSOP pinout, so PCB reuse across family members is straightforward; the ROHM second source adds supply-chain flexibility with no layout change.

مقایسه با جایگزین‌ها

پارامتر این محصول LM393BPWR LM2903BPWR LM393LVPWR LM393PWR (ROHM)
Package 8-TSSOP (PW) 8-TSSOP (PW) - same 8-TSSOP (PW) - same 8-TSSOP (PW) - same 8-TSSOP (PW) - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments ROHM Semiconductor
Number of Comparators 2 2 2 2 2
Output Type Open-collector Open-collector Open-collector Open-drain Open-collector
Supply Voltage Range Up to 36 V Higher capability than LM393 Higher capability than LM393 Lower voltage range +/-18 V / 36 V
Pin Compatibility Reference (TSSOP-8) Pin-to-pin compatible Pin-to-pin compatible Pin-for-pin per TI Pin-to-pin compatible (industry standard)

تفاوت‌های کلیدی

  • Industry-standard second sourcing (در مقابلLM393PWR (ROHM Semiconductor))
  • Wide 36V single-supply range with ground-including inputs (در مقابلLM393LVPWR)
  • Upgrade path with measurable spec improvements (در مقابلLM393BPWR)

یادداشت‌های طراحی

Every open-collector output must have an external pull-up resistor to a defined rail; choose 10kohm as a general default, lowering to 1kohm-4.7kohm when faster rise times or longer trace drive is required. Route the pull-up to the correct logic rail - not necessarily VCC - to achieve level shifting. Keep input traces short and away from switching nodes; high-impedance comparator inputs readily pick up capacitive coupling from PWM or clock nets, which manifests as false trips.

Without hysteresis, the LM393 output chatters when the input crosses the threshold slowly or when the signal carries noise, since the comparator oscillates through its linear region. Add positive feedback (resistor from output to the non-inverting input, typically in the 100kohm range) sized so the trip-to-release gap exceeds the expected noise amplitude. Remember the effective feedback amplitude differs on output-high (pull-up divider) versus output-low (hard ground) states, so calculate hysteresis for both output states separately.

The LM393 quiescent current is independent of supply voltage, but total current consumption equals quiescent current plus pull-up resistor current whenever an output is low. For battery applications, select larger pull-up values (47kohm-100kohm) if edge speed permits, and place the trip logic so outputs idle high. Decouple VCC with a 100nF ceramic capacitor placed close to pin 8; during output transitions the device draws dynamic current that can couple rail noise into the other comparator in the same package.

The PNP input stage allows common-mode input down to ground, but the inputs must remain within the valid common-mode range at the top end (approximately VCC minus 1.5V per classic LM393 family behavior). Exceeding the common-mode range can invert comparator response unexpectedly. When comparing signals that approach the upper rail, divide them down first or choose the LM393LV/LM393B with wider input-range specifications for low-voltage designs.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

Compliance status not stated in the retrieved sources; consult the TI LM393 product page at ti.com/product/LM393 for current RoHS/REACH declarations.

تاریخ تأیید داده‌ها: 2026-11-08 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

lm393pwr datasheet LM393PWR datasheet pdf LM393PWR pinout Texas Instruments LM393PWR LM393PWR equivalent LM393PWR replacement LM393PWR vs LM393BPWR LM393 cross reference LM393PWR price LM393PWR stock LM393 TSSOP-8 comparator pinout LM393 battery low voltage monitor circuit

قطعات و اصطلاحات مرتبط

Texas Instruments LM393PWR LM393 LM393B LM2903B LM393LV LM2903 ROHM Semiconductor dual differential comparator voltage comparator open-collector output wire-AND TSSOP-8 PW package hysteresis undervoltage lockout window comparator input offset voltage quiescent current single-supply operation RoHS surface mount
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ