LT1057ISW - Dual 14V/us Precision JFET Op Amp | Analog Devices
Артикул: LT1057ISW ✓ АктивенLT1057ISW Обзор
A JFET-input operational amplifier is a voltage-amplifier IC whose input stage uses junction field-effect transistors. This input architecture is valued for high input impedance, very low bias current, and low input-current noise. Within the broader semiconductor hierarchy, the LT1057 is an operational amplifier, a precision analog amplifier, and a linear integrated circuit intended for signal conditioning rather than power conversion.
The LT1057 combines a 14 V/us typical slew rate with a minimum 5 MHz gain-bandwidth product. Its fast settling performance reaches 0.02%, making it useful where signal transitions must settle accurately at relatively high operating frequencies. The typical input offset voltage is 150 uV, with a maximum of 450 uV for the LT1057, while the low 10 pA bias current supports high-impedance sensing and minimizes current-dependent errors.
The matched dual configuration supports precision applications requiring two amplifier channels with similar behavior. It can serve as a dual noninverting amplifier, dual difference amplifier, instrumentation front end, sample-and-hold buffer, or active-filter building block. The 8-pin configuration supports common industry-standard dual-op-amp layouts, reducing design changes when moving from older bipolar or JFET-input dual amplifiers to the LT1057 family.
Typical uses include precision instrumentation, low-level signal conditioning, high-impedance sensor interfaces, active filters, and analog measurement systems. The low bias current is especially beneficial when source impedances are high, while the 14 V/us typical slew rate helps preserve signal integrity when driving moderate capacitances or processing faster waveforms.
When laying out a circuit, place input and feedback components close to the relevant amplifier pins and keep sensitive input traces away from high-current switching paths. Provide stable bypassing at the power pins, verify output-current and supply-voltage limits against the manufacturer specifications, and check stability when driving capacitive loads.
This product page combines the LT1057 family specifications, manufacturer documentation, package information, cross-reference candidates, and practical guidance for evaluating the LT1057ISW in precision analog systems.
Аналоги без доработки для LT1057ISW — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
LT1057CSW
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LT1057IS
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LF412A
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
OP-215
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT1057ISW Максимальные параметры и электрические характеристики
| Amplifier Type | Dual precision operational amplifier |
| Input Transistor Type | JFET |
| Number of Amplifiers | 2 circuits |
| Slew Rate | 14 V/us typical; 10 V/us minimum |
| Gain-Bandwidth Product | 5 MHz minimum |
| Input Offset Voltage | 150 uV typical; 450 uV maximum |
| Input Bias Current | 10 pA |
| Settling Performance | 0.02% fast settling time |
| Channel Matching | Matched dual amplifier |
| Operating Temperature Grade | Industrial |
| Корпус | 8-pin SOIC |
| Тип монтажа | Surface mount |
Конфигурация выводов LT1057ISW
| Контакт 1 | OUT A — Channel A output |
| Контакт 2 | -IN A — Channel A inverting input |
| Контакт 3 | +IN A — Channel A non-inverting input |
| Контакт 4 | V- — Negative power supply |
| Контакт 5 | +IN B — Channel B non-inverting input |
| Контакт 6 | -IN B — Channel B inverting input |
| Контакт 7 | OUT B — Channel B output |
| Контакт 8 | V+ — Positive power supply |
Типичное применение
LT1057ISW подходит для 6 применениеs: Precision Instrumentation Front End, High-Impedance Sensor Signal Conditioning, Active Audio and Control Filters, Low-Level Measurement Amplifier, High-Speed Analog Signal Conditioning, Sample-and-Hold Buffer Stage.
Precision Instrumentation Front End
The LT1057ISW fits precision instrumentation because its JFET input stage has a 10 pA bias current and its typical input offset voltage is 150 uV, helping limit errors in low-level sensor signals. The two matched channels can support differential signal conditioning without introducing substantial channel mismatch. With a minimum gain-bandwidth product of 5 MHz and a 14 V/us typical slew rate, the amplifier also retains useful bandwidth and transient performance. Place the amplifier close to the sensing network, keep input traces short, and verify the required gain and common-mode range against the application limits.
Рекомендуется
High-Impedance Sensor Signal Conditioning
The LT1057ISW is well suited to high-impedance sensor interfaces because its specified 10 pA input bias current minimizes the error produced when bias current flows through a large source resistance. Its 150 uV typical offset voltage supports accurate amplification of small transducer outputs, while the 5 MHz minimum gain-bandwidth product provides more bandwidth than a purely low-frequency precision amplifier may require. The dual channels can condition complementary sensor outputs or provide gain and filtering functions. PCB insulation, guarded input routing, and clean grounding remain important because high-impedance nodes can collect leakage and stray interference.
Рекомендуется
Active Audio and Control Filters
The LT1057ISW can implement active filtering in audio and control systems where both low input current and fast transient response are valuable. Its 14 V/us typical slew rate and 10 V/us minimum slew rate provide ample large-signal response for moderate filter frequencies, while the 5 MHz minimum gain-bandwidth product supports accurate closed-loop behavior above the audio band. The matched dual architecture permits two filter sections with similar AC characteristics. Component tolerances and amplifier gain accuracy should be calculated together, and output loading must remain within the device's operating limits.
Рекомендуется
Low-Level Measurement Amplifier
The LT1057ISW suits low-level measurement stages that combine high source impedance with accurate signal representation. The 10 pA input bias current reduces the voltage offset caused by source resistance, and the 150 uV typical input offset voltage limits additional signal error. Two amplifiers can form a precision difference stage when component matching and resistor-network accuracy are adequate. The 5 MHz minimum gain-bandwidth product helps preserve signal shape, while the 14 V/us typical slew rate improves response to fast input transitions. Input common-mode and output swing limits must be checked before finalizing the gain plan.
Рекомендуется
High-Speed Analog Signal Conditioning
The LT1057ISW is appropriate for moderate-speed analog conditioning because its minimum 5 MHz gain-bandwidth product and 14 V/us typical slew rate provide faster response than a general-purpose precision amplifier may offer. Its JFET inputs also preserve low input bias current, allowing the same device to condition relatively high-impedance sources. The amplifier can be used in gain, inversion, impedance conversion, or active-filter stages. Pay attention to settling behavior for small-signal measurements and add isolation when driving capacitive loads that could otherwise create excessive output current or instability.
Рекомендуется
Sample-and-Hold Buffer Stage
The LT1057ISW can form a sample-and-hold buffer using one channel for acquisition and the other for complementary processing. Its low 10 pA input bias current reduces the disturbance imposed on the signal source, and its 14 V/us typical slew rate helps the output follow changing input levels. The minimum 5 MHz gain-bandwidth product supports closed-loop bandwidth required by the sampling interval. The exact hold capacitor, switch arrangement, and settling target require a detailed stability and error analysis, while supply bypassing should be positioned close to the amplifier pins.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LT1057ISW — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LT1057CSW | LT1057IS | LF412A | OP-215 |
|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Texas Instruments | Analog Devices |
| Amplifier Configuration | Matched dual | Dual | Dual | Dual | Dual |
Ключевые отличия
- Fast slew rate within a precision JFET-input dual amplifier (против OP-215)
- Manufacturer-identified upgrade path for LF412A systems (против LF412A)
- Matched dual-channel architecture (против LT1057IS)
Заметки по проектированию
Place each input, feedback, and supply-bypass component close to its associated LT1057ISW pin. Sensitive non-inverting inputs should have short traces and a grounded guard where practical. Because the JFET input bias current is specified at 10 pA, long PCB leakage paths and contaminated surfaces can become significant at very high source impedances.
Do not treat nominal offset voltage as the total error budget. Include resistor tolerance, input bias-current error, noise, output loading, and temperature effects in the calculation. With a 150 uV typical input offset and 10 pA input bias current, source resistance and resistor-network errors can become comparable to the amplifier offset in precision measurement circuits.
Use the 14 V/us typical slew rate and 10 V/us minimum slew rate as design limits when driving capacitive or long interconnects. Estimate output-current demand from capacitive load and slew rate, then verify stability with an isolation resistor if the load is highly capacitive. Maintain short output paths and provide local supply bypassing to reduce transient disturbance.
Информация о соответствии
The available product documentation identifies an industrial-grade dual JFET-input operational amplifier but does not establish the target MPN's RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.