LT8331IMSE#PBF - 140V 0.5A Boost/SEPIC/Flyback Conv | ADI
Артикул: LT8331IMSE#PBF ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.5 | $6,50 |
| 10 | $6.18 | $61,80 |
| 100 | $5.46 | $546,00 |
| 500 | $4.91 | $2.455,00 |
| 1.000 | $4.36 | $4.360,00 |
LT8331IMSE#PBF Обзор
A switching converter (also called a DC/DC switching regulator or SMPS - Switch-Mode Power Supply) uses energy storage elements (inductors and capacitors) and a power switch to convert one DC voltage to another DC voltage with much higher efficiency than linear regulators. The LT8331 belongs to the boost/SEPIC/flyback/inverting sub-family of non-isolated/isolated-capable switching regulators, which sits within the broader power management IC category. These topologies are preferred over linear regulators when high step-up ratios, high step-down ratios, or negative rails are required, especially at input voltages above 30V.
Key specifications include a programmable switching frequency range of 100 kHz to 500 kHz, 6 uA quiescent current in Burst Mode operation, a SYNC/MODE pin for external clock synchronization or Burst/pulse-skipping selection, and a BIAS pin that allows the IC to be powered from its own output for increased efficiency. The internal current-mode architecture provides stable operation across a wide range of input and output voltages.
The LT8331 employs a high-voltage DMOS power switch with current-mode control and internal compensation. The unique single FB pin allows the same IC to be reconfigured for boost, SEPIC, flyback, or inverting configurations simply by changing the external component connections - a significant engineering advantage for multi-rail designs. The 100V max Vin+ tolerance supports 4:1 input range industrial bus systems and automotive load-dump transients.
Typical applications include industrial 24V/48V bus converters, automotive power conditioning, isolated flyback bias supplies, negative voltage generators for op-amp and ADC rails, battery-powered systems requiring high step-up ratios, and telecom infrastructure. The wide input range makes it especially attractive for systems that must survive wide input transients.
When designing with the LT8331, carefully calculate maximum switch voltage stress in flyback/SEPIC topologies - the 140V internal switch rating provides generous headroom but requires proper snubber design for reliable operation. Use the SYNC pin to synchronize multiple converters in noise-sensitive systems.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для LT8331IMSE#PBF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LT8331EMSE#PBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT8331IMSE#WPBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT8331IMSE#WTRPBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT8331IMSE#TRPBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT3571EUB#PBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT8331IMSE#PBF Максимальные параметры и электрические характеристики
| Топология | Boost, SEPIC, Flyback, Inverting |
| Диапазон входного напряжения | 4.5 V to 100 V |
| Internal Switch Voltage Rating | 140 V |
| Internal Switch Current | 0.5 A |
| Количество выходов | 1 |
| Выходное напряжение | Adjustable (Positive or Negative) |
| Частота переключения | 100 kHz to 500 kHz (programmable) |
| Quiescent Current (Burst Mode) | 6 uA |
| Напряжение обратной связи | 1.6 V (positive), -0.8 V (negative) |
| Synchronization | Yes (SYNC/MODE pin) |
| BIAS Pin | Yes (for efficiency optimization) |
| Control Mode | Current Mode (internally compensated) |
| Корпус | 16-TFSOP (MSOP-16) with 12 leads and exposed pad |
| Диапазон рабочих температур | -40 C to +125 C (I grade) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
Конфигурация выводов LT8331IMSE#PBF
| Контакт 1 | SW — Switch node - connect to inductor/transformer primary |
| Контакт 2 | VIN — Input supply voltage (4.5V to 100V) |
| Контакт 3 | BIAS — Optional second supply input for improved efficiency |
| Контакт 4 | SS — Soft-start programming pin |
| Контакт 5 | RT — Timing resistor for switching frequency programming |
| Контакт 6 | SYNC/MODE — External clock sync or Burst Mode/pulse-skipping selection |
| Контакт 7 | FB — Feedback (1.6V positive / -0.8V negative reference) |
| Контакт 8 | GND — Ground |
| Контакт 9 | NC — Not connected (per datasheet) |
| Контакт 10 | NC — Not connected (per datasheet) |
| Контакт 11 | NC — Not connected (per datasheet) |
| Контакт 12 | NC — Not connected (per datasheet) |
| Контакт 13 | PGND — Power ground (exposed pad internally connected) |
| Контакт 14 | PGND — Power ground (exposed pad internally connected) |
| Контакт 15 | PGND — Power ground (exposed pad internally connected) |
| Контакт 16 | PGND — Power ground (exposed pad internally connected) |
Типичное применение
LT8331IMSE#PBF подходит для 6 применениеs: Industrial 24V/48V Bus Converter, Automotive Power Conditioning, Isolated Flyback Bias Supply, Negative Voltage Generator for Op-Amp and ADC Rails, Battery-Powered High Step-Up Systems, Telecom and PoE Auxiliary Bias.
Industrial 24V/48V Bus Converter
The LT8331IMSE#PBF is well-matched to 24V and 48V industrial bus inputs because of its 100V maximum continuous input rating and 140V internal switch, which together provide generous transient margin for inductive kickback and load-dump events. The device's 4.5V minimum input supports battery-backed 24V systems during brownout, while the 0.5A internal switch delivers up to several watts of regulated output in boost, SEPIC, or buck-derived topologies. Industrial designers favor the part's SYNC/MODE pin, which allows multiple converters to be clocked from a common oscillator to avoid beat-frequency EMI in densely packed control cabinets. The MSOP-16 footprint with exposed pad keeps the solution size compact for DIN-rail mounted PLCs and sensor hubs.
Рекомендуется
Automotive Power Conditioning
The LT8331IMSE#PBF's 100V input tolerance handles automotive load-dump transients up to ISO 7637-2 severity levels when paired with a simple upstream TVS clamp, making it suitable for body electronics and 12V/24V truck systems. The 140V internal switch supports boost topologies that step up cranking transients to stable 15V or 18V rails for downstream ECU microcontrollers and CAN transceivers. For automotive designs requiring formal qualification, the pin-compatible LT8331IMSE#WPBF variant offers AEC-Q100 controlled manufacturing. The 6 uA Burst Mode IQ is critical for key-off quiescent current budgets in always-powered telematics modules, where standby drain directly affects battery life over months of parking.
Рекомендуется
Isolated Flyback Bias Supply
The LT8331IMSE#PBF in flyback configuration delivers isolated bias voltages for gate drivers, isolated signal acquisition, and industrial fieldbus interfaces. The 140V internal switch and 100V input tolerance support wide-input isolated converters commonly used in 24V-to-5V or 48V-to-3.3V telecom and factory-automation rails. The single FB pin simplifies primary-side regulation design, while the BIAS pin can power the LT8331's internal circuitry from the auxiliary winding to maximize efficiency across the full load range. With proper snubber design, the flyback topology achieves 80%+ efficiency at moderate loads - significantly higher than linear regulators at large VIN-VOUT deltas. Designers should validate peak switch voltage stress including leakage inductance spikes.
Рекомендуется
Negative Voltage Generator for Op-Amp and ADC Rails
The LT8331IMSE#PBF in inverting configuration generates negative rails such as -5V, -12V, or -15V needed by legacy op-amps, precision ADCs, and biasing circuits from a single positive supply. The unique single FB pin with -0.8V reference eliminates the dual-feedback networks required by some competing converters, simplifying the BOM. With 0.5A switch current and 100V input tolerance, the LT8331 can generate negative rails from high-voltage positive inputs while maintaining the -40C to +125C operating range required by industrial test equipment. The SYNC/MODE pin allows the negative rail converter to be synchronized away from sensitive analog sampling windows in mixed-signal data acquisition systems.
Рекомендуется
Battery-Powered High Step-Up Systems
The LT8331IMSE#PBF excels in battery-powered applications requiring high step-up ratios - for example, boosting a single-cell Li-ion (3.0V-4.2V) up to 24V or 36V for sensor excitation or LCD bias. The 4.5V minimum input supports two-cell Li-ion packs and 5V USB inputs, while the 140V internal switch tolerates high reflected voltages in extreme step-up ratios. Burst Mode operation with 6 uA quiescent current extends battery life in always-on IoT sensor nodes that spend most of their time in standby. The MSOP-16 footprint suits space-constrained wearable and IoT designs where every square millimeter of PCB counts toward miniaturization targets.
Рекомендуется
Telecom and PoE Auxiliary Bias
The LT8331IMSE#PBF supports telecom infrastructure designs that require auxiliary bias supplies derived from 48V backplane rails. The 100V input rating covers the full 36V-72V telecom range plus transient headroom, while the 140V internal switch provides margin for boost-derived housekeeping rails. The LT8331's SYNC/MODE pin can synchronize to a master system clock to keep switching harmonics out of sensitive RF bands. In PoE Powered Device (PD) applications, the LT8331 can derive secondary rails after the PD interface IC has negotiated power with the Power Sourcing Equipment - useful for IP phones, wireless access points, and security cameras.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LT8331IMSE#PBF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LT8331EMSE#PBF | LT8331IMSE#WPBF | LT8331IMSE#WTRPBF | LT8331IMSE#TRPBF | LT3571EUB#PBF |
|---|---|---|---|---|---|---|
| Package | 16-TFSOP (MSOP-16, 12-lead EP) | 16-TFSOP (MSOP-16, 12-lead EP) - same | 16-TFSOP (MSOP-16, 12-lead EP) - same | 16-TFSOP (MSOP-16, 12-lead EP) - same | 16-TFSOP (MSOP-16, 12-lead EP) - same | 10-MSOP - smaller package |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Input Voltage Range | 4.5 V to 100 V | 4.5 V to 100 V | 4.5 V to 100 V | 4.5 V to 100 V | 4.5 V to 100 V | 2.5 V to 75 V |
| Internal Switch Voltage | 140 V | 140 V | 140 V | 140 V | 140 V | 75 V |
| Operating Temperature | -40 C to +125 C (I grade) | 0 C to +125 C (E grade) | -40 C to +125 C (AEC-Q100) | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
| Automotive Qualified (AEC-Q100) | No (industrial I grade) | No | Yes (controlled manufacturing) | Yes (controlled manufacturing) | No | No |
Ключевые отличия
- Wide 100V input range with 140V internal switch (против LT8330 (60V max VIN))
- Single FB pin supports 4 topologies (boost/SEPIC/flyback/inverting) (против LT3571EUB#PBF (boost/SEPIC/inverting only, no flyback))
- AEC-Q100 controlled manufacturing variant available (против LT8331IMSE#PBF (industrial I grade))
Заметки по проектированию
The MSOP-16 package with exposed thermal pad requires direct soldering of the EP to a PCB ground plane with thermal vias to a copper pour on inner layers. Estimated: at VIN=24V, VOUT=12V (boost), IOUT=0.3A, the LT8331 internal switch dissipates roughly (1-D)*VIN*ISW ≈ 0.5W steady state. With a 4-layer JEDEC board theta_JA ≈ 40 C/W, junction temperature rise above ambient is about 20C - well within the 125C limit. At VIN=72V boost to VOUT=12V, dissipation increases to roughly 1.2W and thermal analysis becomes more critical. Always populate enough copper area around the EP to keep theta_JA below 45 C/W.
In flyback and SEPIC topologies, peak switch voltage equals VIN plus the reflected output voltage plus leakage inductance spikes. The 140V internal switch rating provides margin, but designers MUST add an RCD snubber or clamp across the transformer primary if calculated worst-case stress exceeds 80% of 140V (i.e., 112V). Estimating leakage spike amplitude requires measuring the transformer's primary leakage inductance (typically 1-3% of magnetizing inductance) and the peak switching current at maximum load. Skipping this analysis is a common cause of field returns with high-voltage switching converters.
Keep the SW node trace short and narrow to minimize radiated EMI, and surround it with a ground copper pour. Place input ceramic bypass capacitors (1uF X7R minimum, 4.7uF recommended for high-voltage transients) within 5mm of the VIN pin. The RT resistor should be placed close to the RT pin with the SYNC/MODE trace routed away from the SW node to avoid capacitive coupling that can disrupt synchronization. The exposed pad ground must use multiple thermal vias (at least 9 vias in a 3x3 pattern with 0.3mm drill) for proper heat extraction in sustained-load applications.
Информация о соответствии
Lead-free per the #PBF suffix. The #WPBF variant is AEC-Q100 qualified for automotive; the standard LT8331IMSE#PBF (I grade) is industrial-grade.
