LT8609AIMSE - 42V, 3A Synchronous Buck Regulator | Analog Devices
Артикул: LT8609AIMSE ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $3.68 | $3,68 |
| 10 | $3.68 | $36,80 |
| 100 | $3.68 | $368,00 |
| 500 | $3.68 | $1.840,00 |
| 1.000 | $3.68 | $3.680,00 |
LT8609AIMSE Обзор
A synchronous buck converter is a switching DC-DC regulator category within power management integrated circuits. Its high-side switch charges an inductor during one switching phase, while its low-side synchronous switch provides a discharge path during the other phase. This topology converts a higher input voltage to a lower regulated output with high efficiency. Compared with a linear regulator, the synchronous architecture reduces dissipation when the input-to-output voltage difference is substantial, making it suitable for battery, industrial, communications, and automotive systems.
Key verified features include a 42 V maximum input rating, continuous current capability up to 3 A for the LT8609A family, 2.5 µA quiescent current, and Burst Mode operation that maintains output ripple below 10 mVP-P at low output currents. The family also provides frequency synchronization through a SYNC pin, according to the manufacturer product page and datasheet search result. These characteristics allow the regulator to balance efficiency, transient response, and board area.
The LT8609AIMSE is an industrial-temperature ordering option in the LT8609 family, identified by the I temperature grade and MSE package designation. The provided distributor listing identifies a 10-MSOP package with exposed pad, approximately 3.00 mm wide. The exposed thermal pad must be connected to ground and used as a heat-spreading feature when operating at sustained high loads. Electrical details such as switching frequency, output-voltage accuracy, control-loop compensation, and absolute maximum ratings beyond the verified values should be confirmed in the current Analog Devices datasheet.
Typical applications include telecom and data-communication equipment, industrial control systems, battery-powered equipment, notebook and tablet power rails, and distributed power systems. A 42 V input rating also allows use in industrial buses when transient and surge requirements are properly addressed. The regulator is most useful where a 3 A load capability and low no-load consumption are required without using a larger power package.
When designing around the LT8609AIMSE, select the inductor and input/output capacitors according to the datasheet guidance, keep the switching loop layout compact, and provide adequate copper area around the exposed pad. Verify startup behavior, output ripple, load-transient response, and thermal rise at the highest expected input voltage and load. The main trade-off is switching-regulator output ripple compared with a low-noise linear regulator, so sensitive analog loads may still require post-filtering.
Аналоги без доработки для LT8609AIMSE — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LT8609EMSE
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT8609AEMSE
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT8608EMSE
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT8607HMSE
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT8609AIMSE Максимальные параметры и электрические характеристики
| Product Type | Synchronous step-down switching regulator |
| Maximum Input Voltage | 42 V |
| Continuous Output Current | 3 A for LT8609A family |
| Выходное напряжение | 0.782 V adjustable minimum |
| Ток покоя | 2.5 µA |
| Non-Switching Quiescent Current | 1.7 µA |
| Switching Topology | Monolithic synchronous buck converter |
| Integrated Switches | High-side and low-side power switches |
| Light-Load Operation | Burst Mode |
| Low-Load Output Ripple | Below 10 mVP-P |
| Frequency Synchronization | Available through SYNC pin |
| Корпус | 10-MSOP with exposed pad |
| Package Width | 3.00 mm |
| Тип монтажа | Surface mount |
| Temperature Grade | Industrial grade |
Руководство по цоколевке LT8609AIMSE в корпусе 3.00 mm
Цоколевка для LT8609AIMSE (корпус 3.00 mm). Этот силовой прибор имеет выводы затвора, стока и истока. Для неполяризованных корпусов обратитесь к техническому описанию производителя для точной ориентации вывода 1 и деталей посадочного места. Типичные применения включают проектирование источников питания, управление двигателями и коммутацию нагрузки.
Нет подробных данных о распиновке для LT8609AIMSE.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
LT8609AIMSE подходит для 6 применениеs: Industrial 24 V Bus Power Rail, Battery-Powered Sensor Node, Communications Module Power, Portable Computing Power Rail, Distributed Power System, Automotive or Rugged 42 V Input System.
Industrial 24 V Bus Power Rail
The LT8609AIMSE suits industrial equipment powered from a nominal 24 V bus when the design needs a compact, efficient step-down stage. Its verified 42 V maximum input rating provides margin above the nominal bus, while the LT8609A family's 3 A capability supports processor, sensor, and communications loads. The low quiescent current of 2.5 µA is useful during idle periods, and the exposed-pad MSOP permits copper-based heat spreading. Confirm transient protection, input filtering, and the final maximum bus voltage before release.
Рекомендуется
Battery-Powered Sensor Node
For battery-operated sensor and IoT equipment, the LT8609AIMSE offers a low standby-consumption option for converting a battery-derived input to a regulated rail. The family's 2.5 µA quiescent current helps reduce unnecessary drain between measurement or communication intervals, while Burst Mode supports light-load operation. Its synchronous topology can reduce conversion loss compared with a linear stage when the voltage difference is substantial. Designers should still evaluate battery chemistry, peak load current, leakage, and sleep-mode behavior.
Рекомендуется
Communications Module Power
The LT8609AIMSE can provide a compact high-efficiency rail for communications equipment with changing load demands. The LT8609A family is specified for continuous current up to 3 A, making it relevant for RF, modem, and digital-interface loads that need more than a low-current sensor regulator. Burst Mode can improve light-load behavior, and the SYNC pin offers a path to coordinate timing when required by the system. Verify peak transient loads, EMI behavior, and inductor saturation margin.
Рекомендуется
Portable Computing Power Rail
The LT8609AIMSE is appropriate for compact portable-device power trees where a 42 V-capable buck stage is useful for protecting against input transients and where low no-load consumption contributes to battery life. Its 10-MSOP format supports space-constrained layouts, while synchronous operation can improve efficiency in a multi-rail system. The switching output should be checked for ripple sensitivity, and the device's exposed pad should be tied to ground with adequate copper. Use the manufacturer’s recommended inductor and capacitor values.
Рекомендуется
Distributed Power System
The LT8609AIMSE can serve as a local 3 A-class step-down converter in distributed power architectures where multiple rails originate from a higher-voltage source. The 42 V maximum input rating and low quiescent current support efficient point-of-load conversion, while the exposed-pad package helps manage heat through PCB copper. The SYNC function may help coordinate multiple converters in a larger system. The final design must account for converter sequencing, startup behavior, EMI filtering, and the exact compensation requirements of the LT8609A.
Рекомендуется
Automotive or Rugged 42 V Input System
The LT8609AIMSE may be evaluated for rugged 12 V or 24 V systems that need headroom for transient events, provided the final electrical and environmental requirements are verified. Its 42 V maximum input rating is a useful starting point, but automotive qualification and surge protection are not confirmed in the supplied data. The synchronous buck topology can supply a compact rail for control electronics, relays, sensors, or communications equipment. Check transient clamping, temperature range, EMI, and qualification requirements before deployment.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LT8609AIMSE — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LT8609EMSE | LT8609AEMSE | LT8608EMSE | LT8607HMSE | LMR33630 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Texas Instruments |
| Package | 10-MSOP with exposed pad | 10-MSOP with exposed pad | 10-MSOP with exposed pad | 10-MSOP with exposed pad | 10-MSOP with exposed pad | 3x3 mm WSON |
Ключевые отличия
- Verified low standby consumption (против LT8609EMSE)
- 42 V input capability in a compact MSOP (против LMR33630)
- High-side and low-side switches integrated (против LT8608EMSE)
- Low-load ripple behavior (против LT8607HMSE)
Заметки по проектированию
Estimated thermal design must begin with the actual worst-case conversion loss because the verified data does not include package thermal resistance. Estimate conduction loss from the high-side and low-side resistance and switching loss from voltage, current, frequency, and transition time; multiply by the duty-cycle duty factor. Check the resulting junction temperature against the datasheet limit and use the exposed pad, ground copper, and via array to spread heat. Confirm the estimate on the assembled PCB.
Place input capacitors, the switching node, the inductor, and the LT8609AIMSE in a compact high-current loop. Keep the exposed pad connected to a low-impedance ground plane and use multiple vias where electrical and thermal limits permit. Route the feedback or output-sense connection away from the switching node and inductor to reduce noise injection. Follow the exact capacitor and layout diagrams in the current manufacturer datasheet.
Select the inductor and output capacitors using the manufacturer’s stated current-limit, ripple, stability, and compensation guidance. The verified 3 A family capability does not guarantee 3 A in every layout or thermal condition. Check inductor saturation margin, capacitor voltage derating, output ripple at light and heavy loads, and startup into the intended load. Do not rely on generic buck-converter capacitor values.
The ordering code matters: LT8609AIMSE identifies a specific A-version, industrial-grade, MSE-package option, while package, temperature-grade, and tape-and-reel suffixes can change the orderable device. Do not substitute a similar LT8609, LT8608, or LT8607H part solely because it appears in the same package family. Compare the official pinout, electrical limits, switching frequency, compensation, and exposed-pad connection first.
Информация о соответствии
The supplied manufacturer and distributor search results do not explicitly state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status for LT8609AIMSE. The industrial temperature-grade ordering code should not be treated as proof of AEC-Q100 qualification.
