LT8640SEV-2#PBF - 42V, 6A Synchronous Step-Down Silent Switcher | ADI
Артикул: LT8640SEV-2#PBF ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $15.84 | $15,84 |
| 10 | $14.85 | $148,50 |
| 100 | $12.5 | $1.250,00 |
| 500 | $10.75 | $5.375,00 |
| 1.000 | $9.2 | $9.200,00 |
LT8640SEV-2#PBF Обзор
What is a Silent Switcher buck regulator? A synchronous buck converter is a switch-mode DC-DC topology that steps down a higher input voltage to a lower regulated output using a pair of MOSFET switches and an LC output filter; it replaces a traditional buck diode with a synchronous MOSFET to reduce conduction loss. The Silent Switcher 2 architecture further minimizes EMI by splitting the input hot loop into symmetrical parallel paths, enabling the LT8640SEV-2 to meet CISPR 25 / CISPR 32 Class 5 radiated and conducted EMI limits with minimal filtering, which is essential for noise-sensitive automotive and industrial designs.
Key specifications include a 30 ns minimum on-time that supports high step-down ratios even at 2 MHz switching frequency, 96% peak efficiency, 2.5 uA quiescent current in Burst Mode operation, and 200 kHz to 3 MHz programmable switching frequency. The device supports spread-spectrum frequency modulation, external clock synchronization, pulse-skipping, and forced continuous modes through the SYNC/MODE pin, and includes internal loop compensation to simplify PCB design. The 24-LQFN exposed pad provides low thermal resistance for sustained 6 A operation.
The peak current-mode control architecture with 30 ns minimum top switch on-time enables high VIN-to-low-VOUT conversion at high switching frequencies (e.g., 24 V to 1.0 V at 2 MHz). Internal MOSFETs are optimized for both high efficiency and thermal performance, supporting up to 6 A continuous load with no external heatsink required when VIN-VOUT differential is moderate.
Typical applications include automotive infotainment and ADAS power rails, industrial 24 V bus to point-of-load conversion, battery-powered systems (12 V / 24 V / 36 V Li-ion stacks), GPS / telematics modules, and low-EMI communications infrastructure. The 2.5 uA quiescent current also makes it suitable for always-on bias supplies.
Design trade-off: the -2 variant is specified for tighter EMI compliance but is otherwise equivalent to the LT8640SEV; the standard -1 (LT8640S/LT8640SA) and non-EMI -2 variants coexist on the same datasheet for design flexibility. Always place input ceramics directly at the VIN and PGND pins to maximize the benefit of Silent Switcher 2.
This page synthesizes distributor pricing, verified drop-in alternatives from the LT8640S / LT8643S-2 family, and practical design notes not duplicated in the manufacturer datasheet, providing an engineer-ready decision matrix for selecting the right synchronous buck for low-EMI applications.
Аналоги без доработки для LT8640SEV-2#PBF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LT8640SEV-2#PBF (тот же форм-фактор и посадочное место) — отличается по Output Voltage Range, Architecture, MSL Level, Operating Junction Temperature, Package.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LT8643SEV-2#PBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT8640SEV#PBF
✅ Прямая замена✓ В наличии
$6.93 / шт.
Открыть даташит →LT8640SHV-2#WPBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT8640SIV#PBF
✅ Прямая замена✓ В наличии
$4.95 / шт.
Открыть даташит →LT8642SIV#PBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT8640SEV-2#PBF Максимальные параметры и электрические характеристики
| Топология | Synchronous Step-Down (Buck) |
| Диапазон входного напряжения | 3.4 V to 42 V |
| Диапазон выходного напряжения | 0.97 V to 41.58 V (adjustable) |
| Максимальный выходной ток | 6 A |
| Switching Frequency Range | 200 kHz to 3 MHz |
| Minimum Switch On-Time | 30 ns |
| Peak Efficiency | 96% |
| Quiescent Current (Burst Mode) | 2.5 uA |
| Architecture | Silent Switcher 2 (ultra-low EMI) |
| Control Mode | Peak Current-Mode |
| Synchronization | External clock, SYNC/MODE pin (spread spectrum, pulse-skipping, forced continuous) |
| Корпус | 24-LQFN-EP (4 mm x 6 mm) |
| Рабочая температура перехода | -40C to +125C |
| Тип монтажа | Surface Mount |
| Уровень MSL | 3 |
| Статус RoHS | Compliant |
| EMI Compliance | CISPR 25 / CISPR 32 Class 5 (with minimal filtering) |
Конфигурация выводов LT8640SEV-2#PBF
| Контакт 1 | VIN — Input supply voltage |
| Контакт 2 | VIN — Input supply voltage |
| Контакт 3 | PGND — Power ground |
| Контакт 4 | PGND — Power ground |
| Контакт 5 | SW — Switch node (output to inductor) |
| Контакт 6 | SW — Switch node (output to inductor) |
| Контакт 7 | SW — Switch node (output to inductor) |
| Контакт 8 | SW — Switch node (output to inductor) |
| Контакт 9 | BOOST — Bootstrap capacitor for top gate drive |
| Контакт 10 | BIAS — Internal LDO bias supply decoupling |
| Контакт 11 | EN/UVLO — Enable / undervoltage lockout threshold |
| Контакт 12 | RT — Timing resistor to program switching frequency |
| Контакт 13 | SYNC/MODE — Sync input / mode selection (spread spectrum, pulse-skipping, forced continuous) |
| Контакт 14 | FB — Voltage feedback for adjustable output |
| Контакт 15 | PGND — Power ground (signal) |
| Контакт 16 | PGND — Power ground |
| Контакт 17 | PGND — Power ground |
| Контакт 18 | PGND — Power ground |
| Контакт 19 | VIN — Input supply voltage |
| Контакт 20 | VIN — Input supply voltage |
| Контакт 21 | NC — Not connected (per datasheet) |
| Контакт 22 | NC — Not connected (per datasheet) |
| Контакт 23 | NC — Not connected (per datasheet) |
| Контакт 24 | NC — Not connected (per datasheet) |
| Контакт EP | EP — Exposed thermal pad - solder to PGND copper pour for heatsinking |
Типичное применение
LT8640SEV-2#PBF подходит для 7 применениеs: Automotive Infotainment Power Rail, Industrial 24 V Bus Point-of-Load Conversion, Battery-Powered Portable Equipment, GPS and Telematics Modules, ADAS Sensor Power (Radar / Camera), Low-EMI Communications Infrastructure, Always-On Bias Supply for IoT Edge Nodes.
Automotive Infotainment Power Rail
The LT8640SEV-2#PBF powers 3.3 V / 5 V rails in head units, instrument clusters, and telematics modules from a 12 V / 24 V automotive battery bus. Its Silent Switcher 2 architecture and 30 ns minimum on-time let the part meet CISPR 25 Class 5 radiated/conducted EMI limits with only two small input ceramic capacitors, eliminating the bulky input pi-filters that conventional buck regulators require. Peak efficiency of 96% keeps dissipation under 2 W at typical infotainment loads (1-2 A), and the 2.5 uA Burst-Mode quiescent current preserves battery life during parked/standby states. The 42 V absolute input rating provides margin against 24 V truck-bus load-dump transients.
Рекомендуется
Industrial 24 V Bus Point-of-Load Conversion
The LT8640SEV-2#PBF steps down a 24 V industrial bus (18-32 V typical) to logic rails of 3.3 V, 5 V, or 12 V for PLCs, factory sensors, motor-control boards, and HMI panels. Its 42 V max input tolerates 24 V bus transients and 28 V MIL-STD surges, while the 3.4 V minimum VIN supports cold-start scenarios. Programmable switching frequency up to 3 MHz allows engineers to place the switching harmonics away from sensitive sensor bands; spread-spectrum mode further reduces EMI in dense multi-rail designs. The exposed thermal pad plus a 1 oz copper pour sustains full 6 A at 24 V-to-5 V conversion without external heatsinking.
Рекомендуется
Battery-Powered Portable Equipment
The LT8640SEV-2#PBF operates from 3.4 V to 42 V and consumes only 2.5 uA in Burst Mode, making it well-suited for battery stacks from 4S Li-ion (12-16.8 V) through 8S (28-33.6 V). Portable medical devices, test instruments, and field-deployed IoT gateways benefit from its high efficiency (>94% at 12 V-to-3.3 V) and low standby drain, which extends runtime directly. External clock synchronization allows multiple LT8640SEV-2 converters to operate 180 degrees out of phase, reducing input ripple and allowing smaller input capacitors in space-constrained portable designs.
Рекомендуется
GPS and Telematics Modules
The LT8640SEV-2#PBF provides clean 3.3 V / 1.8 V rails for GPS receivers, GNSS modules, and cellular telematics units from an automotive or asset-tracking battery. Silent Switcher 2 architecture prevents converter switching noise from desensitizing the GPS L1/L5 front end or causing phase error in GNSS positioning. The 30 ns minimum on-time supports 12 V-to-1.8 V conversion at 2 MHz with a small 1 uH inductor, reducing both BOM cost and PCB area. The 2.5 uA quiescent current is ideal for asset trackers that spend most of their life in sleep mode.
Рекомендуется
ADAS Sensor Power (Radar / Camera)
The LT8640SEV-2#PBF powers low-voltage rails for 77 GHz radar MMICs, forward-facing camera SoCs, and LiDAR sensor front ends from a 12 V or 24 V automotive supply. CISPR 25 Class 5 EMI compliance prevents the buck converter from raising the noise floor of sensitive analog front ends and high-speed ADCs. Synchronization to an external clock avoids beat-frequency interference with radar chirp or camera pixel clocks. Combined with the LT8640SHV-2#WPBF automotive-grade variant, the part supports AEC-Q100 designs for safety-critical ADAS functions.
Рекомендуется
Low-EMI Communications Infrastructure
The LT8640SEV-2#PBF powers base-station RF chains, small-cell radios, and PoE-powered network equipment where switching-noise-induced phase jitter and spurious emissions must be minimized. Silent Switcher 2 architecture with spread-spectrum modulation distributes noise energy across a wide band, simplifying system-level EMI compliance to EN 55032 Class B. The 200 kHz to 3 MHz programmable switching range allows the fundamental switching tone to be placed in guard bands between sensitive radio bands. Internal compensation eliminates external loop components, reducing PCB complexity in dense RF designs.
Рекомендуется
Always-On Bias Supply for IoT Edge Nodes
The LT8640SEV-2#PBF serves as the always-on bias supply in solar-powered IoT edge nodes, building-automation controllers, and remote sensor gateways. Burst Mode operation at 2.5 uA quiescent current keeps idle drain negligible while still providing fast load-step response for periodic sensor wake events. The wide 3.4 V to 42 V input range accepts direct connection to 12 V lead-acid, 24 V solar battery stacks, or rectified 24 VAC building-bus supplies without front-end regulation. Synchronization to a low-power 32.768 kHz-derived clock minimizes harmonics in the GNSS band.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LT8640SEV-2#PBF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LT8643SEV-2#PBF | LT8640SEV#PBF | LT8640SHV-2#WPBF | LT8640SIV#PBF | LT8642SIV#PBF |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 24-LQFN-EP (4x6 mm) | 24-LQFN-EP (4x6 mm) - same | 24-LQFN-EP (4x6 mm) - same | 24-LQFN-EP (4x6 mm) - same | 24-LQFN-EP (4x6 mm) - same | 24-LQFN-EP (4x6 mm) - same |
| Input Voltage Range | 3.4 V to 42 V | 3.4 V to 42 V | 3.4 V to 42 V | 3.4 V to 42 V | 3.4 V to 42 V | 3.0 V to 42 V |
| Maximum Output Current | 6 A | 8.5 A (+42%) | 6 A | 6 A | 6 A | 10 A (+67%) |
| Silent Switcher Architecture | Silent Switcher 2 (ultra-low EMI) | Silent Switcher 2 (same) | Silent Switcher 1 (higher EMI) | Silent Switcher 2 (same) | Silent Switcher 1 (higher EMI) | Silent Switcher 1 (higher EMI) |
| AEC-Q100 Automotive Grade | No (industrial) | No (industrial) | No (industrial) | Yes (AEC-Q100) | No (industrial) | No (industrial) |
| Minimum Switch On-Time | 30 ns | 30 ns | 30 ns | 30 ns | 30 ns | 30 ns |
| Approx. 1ku List Price (USD) | $6.93 (LT8640S family starting price) | Higher (8.5 A upgrade) | Comparable | Higher (automotive grade) | Comparable | Higher (10 A upgrade) |
Ключевые отличия
- Silent Switcher 2 architecture delivers CISPR 25 Class 5 EMI with minimal filtering (против LT8640SEV#PBF)
- Pin-compatible 8.5 A upgrade path without PCB redesign (против LT8643SEV-2#PBF)
- AEC-Q100 automotive-qualified drop-in variant available (против LT8640SHV-2#WPBF)
Заметки по проектированию
Place two small input ceramic capacitors (e.g., 1 uF + 0.1 uF X7R) directly at the VIN and PGND pins as close as physically possible - this is critical for realizing the full Silent Switcher 2 EMI benefit. Use multiple vias from the LQFN exposed pad to a large PGND copper pour on inner/outer layers to keep junction temperature below 125C at full 6 A load. Estimated: at VIN=24V, VOUT=5V, IOUT=6A, power dissipation is approximately 1.8W, requiring ~1 sq.in. of 1-oz copper for safe operation.
Keep the SW node traces short and narrow to minimize radiated EMI from the high-dV/dt switching node. Place the output inductor away from noise-sensitive analog traces; if possible, shield the inductor with a grounded copper pour. Route the feedback (FB) trace away from the SW node and use a ground guard ring to prevent switching noise from coupling into the regulation loop. For multi-converter designs, synchronize all LT8640SEV-2 ICs 180 degrees out of phase via the SYNC/MODE pin to reduce input ripple.
Do not omit the BOOST capacitor (typically 0.1 uF) between BOOST and SW pins - without it, the top-side gate driver will fail and the converter will not start. Ensure RT resistor is within the 200 kHz to 3 MHz programming range; values outside this range can cause subharmonic instability. For automotive load-dump transients, verify the input TVS clamp limits transients below 42 V - the part's absolute maximum VIN is 42 V continuous with limited transient tolerance above. Do not exceed 6 A continuous without sufficient PCB thermal relief.
Информация о соответствии
RoHS and lead-free compliant per Analog Devices product page (#PBF suffix). LT8640SEV-2#PBF is industrial grade; for AEC-Q100 automotive use choose LT8640SHV-2#WPBF. Halogen-free status not explicitly stated in distributor data.
