LTC2292CUP - Dual 12-Bit 40Msps 3V ADC | Analog Devices
Артикул: LTC2292CUP ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $21.42 | $21,42 |
| 10 | $19.28 | $192,80 |
| 100 | $16.45 | $1.645,00 |
| 500 | $14.85 | $7.425,00 |
| 1.000 | $13.42 | $13.420,00 |
LTC2292CUP Обзор
What is a dual ADC? A dual analog-to-digital converter combines two matched ADC channels on one IC so that the system can digitize two analog inputs simultaneously. The LTC2292CUP belongs to the ADC family (analog-to-digital converter) -> data converter -> signal chain IC -> mixed-signal semiconductor. Each internal channel uses a pipelined multi-stage architecture that converts input samples in successive stages; this trades a small fixed latency for high sampling rates at low power, which is the standard approach for communications, imaging, and instrumentation front ends.
Key features include simultaneous sampling on two channels, a flexible CMOS or LVDS digital output interface, a multiplexed (MUX) output mode that puts both channels on one bus, and selectable input ranges of 1 Vp-p or 2 Vp-p. The device also provides 110 dB channel-to-channel isolation at 100 MHz, internal duty-cycle stabilized clock generation that accepts any duty cycle from 20% to 80%, and a shutdown/power-down pin for portable applications. The exposed thermal pad of the QFN-64 package gives a theta_JA around 28 C/W with proper PCB layout, enabling 235 mW operation without a heatsink.
Typical applications include cellular basestation receiver IF digitizers, portable ultrasound imaging front ends, spectrum analyzer and digital oscilloscope input stages, cable-headend downstream tuners, and multi-channel data acquisition boards for industrial inspection. The wide 70 MHz input bandwidth and high SFDR also make it appropriate for software-defined radio (SDR) and digital pre-distortion feedback paths in RF power amplifier linearization.
When designing with the LTC2292CUP, route analog inputs as 50 ohm controlled-impedance traces with 100 ohm differential terminations when driving the inputs differentially, and stitch the exposed pad (EP) with at least 9 thermal vias to the inner ground plane. A low-noise LDO such as the ADP3338 should supply AVDD, and unused digital outputs may be left floating or three-stated via the OE pin.
Аналоги без доработки для LTC2292CUP — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LTC2292CUP (тот же форм-фактор и посадочное место) — отличается по SNR, Package, SFDR, Operating Temperature, Power Dissipation.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LTC2291CUP
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2293CUP
✅ Прямая замена✓ В наличии
$16.4 / шт.
Открыть даташит →LTC2282CUP
✅ Прямая замена✓ В наличии
$18.5 / шт.
Открыть даташит →LTC2287CUP
✅ Прямая замена✓ В наличии
$7.05 / шт.
Открыть даташит →LTC2280CUP
✅ Прямая замена✓ В наличии
$15.85 / шт.
Открыть даташит →LTC2221CUP
✅ Прямая замена✓ В наличии
$34.2 / шт.
Открыть даташит →LTC2292CUP Максимальные параметры и электрические характеристики
| Manufacturer | Analog Devices (formerly Linear Technology) |
| Part Number | LTC2292CUP |
| Функция | Dual 12-bit ADC |
| Number of Channels | 2 |
| Разрешение | 12 bits |
| Sample Rate | 40 Msps (per channel) |
| Architecture | Pipelined |
| Input Type | Differential or single-ended |
| Input Bandwidth | 70 MHz |
| Напряжение питания | 2.5 V to 3.4 V (single 3V supply) |
| Power Dissipation | 235 mW (typ) |
| SNR | 71.3 dB (Nyquist input) |
| SFDR | 85 dB at 70 MHz input |
| Channel Isolation | 110 dB at 100 MHz |
| Input Range | 1 Vp-p or 2 Vp-p (selectable) |
| Output Interface | CMOS or LVDS, parallel, multiplexed option |
| Корпус | 64-pin QFN (UP, 9x9 mm) with EP |
| Рабочая температура | 0 C to +70 C (C grade) |
| Статус RoHS | Compliant (#PBF suffix) |
Конфигурация выводов LTC2292CUP
| Контакт 1 | OGND — Output driver ground |
| Контакт 2 | D11_1 — Channel 1 digital output bit 11 (MSB) |
| Контакт 3 | D10_1 — Channel 1 digital output bit 10 |
| Контакт 4 | D9_1 — Channel 1 digital output bit 9 |
| Контакт 5 | D8_1 — Channel 1 digital output bit 8 |
| Контакт 6 | D7_1 — Channel 1 digital output bit 7 |
| Контакт 7 | D6_1 — Channel 1 digital output bit 6 |
| Контакт 8 | D5_1 — Channel 1 digital output bit 5 |
| Контакт 9 | D4_1 — Channel 1 digital output bit 4 |
| Контакт 10 | D3_1 — Channel 1 digital output bit 3 |
| Контакт 11 | D2_1 — Channel 1 digital output bit 2 |
| Контакт 12 | D1_1 — Channel 1 digital output bit 1 |
| Контакт 13 | D0_1 — Channel 1 digital output bit 0 (LSB) |
| Контакт 14 | OVDD — Output driver supply |
| Контакт 15 | CLKOUT_1 — Channel 1 clock output (CMOS mode) |
| Контакт 16 | CLKOUT_1+ — Channel 1 LVDS clock output positive |
| Контакт 17 | CLKOUT_1- — Channel 1 LVDS clock output negative |
| Контакт 18 | NC — Not connected |
| Контакт 19 | OGND — Output driver ground |
| Контакт 20 | NC — Not connected |
| Контакт 21 | OE — Output enable (CMOS mode) |
| Контакт 22 | SHDN — Shutdown (active low) |
| Контакт 23 | MODE — Output mode select (CMOS/LVDS) |
| Контакт 24 | MUX — Multiplexed output mode select |
| Контакт 25 | SENSE — Internal reference bypass |
| Контакт 26 | VREF — Reference voltage bypass |
| Контакт 27 | REFTF — Reference top force (decoupling) |
| Контакт 28 | REFBF — Reference bottom force (decoupling) |
| Контакт 29 | REFT — Reference top (decoupling) |
| Контакт 30 | REFB — Reference bottom (decoupling) |
| Контакт 31 | COM — Common-mode voltage (1.5 V) |
| Контакт 32 | AVDD — Analog supply (3V) |
| Контакт 33 | AGND — Analog ground |
| Контакт 34 | AIN+_1 — Channel 1 analog input positive |
| Контакт 35 | AIN-_1 — Channel 1 analog input negative |
| Контакт 36 | TIE_HI_1 — Channel 1 input common tie to COM |
| Контакт 37 | AGND — Analog ground |
| Контакт 38 | AGND — Analog ground |
| Контакт 39 | TIE_HI_2 — Channel 2 input common tie to COM |
| Контакт 40 | AIN-_2 — Channel 2 analog input negative |
| Контакт 41 | AIN+_2 — Channel 2 analog input positive |
| Контакт 42 | AGND — Analog ground |
| Контакт 43 | AVDD — Analog supply (3V) |
| Контакт 44 | COM — Common-mode voltage (1.5 V) |
| Контакт 45 | CLOCK+ — Clock input positive |
| Контакт 46 | CLOCK- — Clock input negative |
| Контакт 47 | AGND — Analog ground |
| Контакт 48 | OVDD — Output driver supply |
| Контакт 49 | D0_2 — Channel 2 digital output bit 0 (LSB) |
| Контакт 50 | D1_2 — Channel 2 digital output bit 1 |
| Контакт 51 | D2_2 — Channel 2 digital output bit 2 |
| Контакт 52 | D3_2 — Channel 2 digital output bit 3 |
| Контакт 53 | D4_2 — Channel 2 digital output bit 4 |
| Контакт 54 | D5_2 — Channel 2 digital output bit 5 |
| Контакт 55 | D6_2 — Channel 2 digital output bit 6 |
| Контакт 56 | D7_2 — Channel 2 digital output bit 7 |
| Контакт 57 | D8_2 — Channel 2 digital output bit 8 |
| Контакт 58 | D9_2 — Channel 2 digital output bit 9 |
| Контакт 59 | D10_2 — Channel 2 digital output bit 10 |
| Контакт 60 | D11_2 — Channel 2 digital output bit 11 (MSB) |
| Контакт 61 | OGND — Output driver ground |
| Контакт 62 | NC — Not connected |
| Контакт 63 | CLKOUT_2- — Channel 2 LVDS clock output negative |
| Контакт 64 | CLKOUT_2+ — Channel 2 LVDS clock output positive |
| Контакт 65 | EP — Exposed pad - solder to ground plane |
Типичное применение
LTC2292CUP подходит для 7 применениеs: Cellular Basestation IF Digitizer, Portable Ultrasound Imaging Front End, Spectrum Analyzer / Digital Oscilloscope Input, Cable Headend Downstream Tuner, Software Defined Radio (SDR) Receiver, Multi-Channel Data Acquisition System, RF Power Amplifier Digital Pre-Distortion Feedback.
Cellular Basestation IF Digitizer
The LTC2292CUP's 71.3 dB SNR and 85 dB SFDR at 70 MHz input make it well-suited for digitizing the IF stage of cellular basestation receivers (WCDMA, LTE, GSM). Placed after a SAW filter and variable-gain amplifier, both channels can simultaneously sample the I and Q paths at 40 Msps, simplifying board layout and reducing component count. The 110 dB channel isolation at 100 MHz prevents crosstalk between I and Q, which is essential for maintaining EVM performance in 3G/4G receivers. The 235 mW dissipation is low enough to allow fanless basestation Remote Radio Head (RRH) designs.
Рекомендуется
Portable Ultrasound Imaging Front End
Dual-channel 12-bit 40 Msps operation makes the LTC2292CUP an ideal front end for portable ultrasound beamformers that require sampling multiple transducer channels at once. With 71 dB SNR and 110 dB channel-to-channel isolation, the ADC supports 50 to 60 dB ultrasound dynamic range requirements while suppressing cross-channel interference that would otherwise create image artifacts. The 235 mW total dissipation per dual channel keeps the system within thermal budget for handheld probes, and the 9x9 mm QFN-64 footprint allows high channel density on the receiver board. The CMOS/LVDS selectable output simplifies interfacing to FPGA-based beamformer ASICs.
Рекомендуется
Spectrum Analyzer / Digital Oscilloscope Input
Test and measurement instruments such as 200 MHz bandwidth oscilloscopes and entry-level spectrum analyzers benefit from the LTC2292CUP's 70 MHz input bandwidth and 85 dB SFDR at full Nyquist. Two matched 40 Msps channels per IC let designers build dual-channel oscilloscope front ends with shared clocking, reducing BOM cost compared with two discrete ADCs. The 110 dB isolation between channels prevents measurement crosstalk that would degrade adjacent-channel spurious performance. Pin-compatible upgrades to LTC2293CUP enable easy extension to higher-bandwidth instrument variants without PCB redesign.
Рекомендуется
Cable Headend Downstream Tuner
QAM downstream tuners in cable headends require ADCs with high spurious-free dynamic range to digitize 256-QAM or 1024-QAM modulated carriers in the 50 to 1000 MHz IF range. The LTC2292CUP provides 85 dB SFDR at 70 MHz and 71 dB SNR, sufficient for capturing multiple QAM carriers simultaneously. Two ADC channels per package allow designers to sample both the main and the diversity or auxiliary IF paths from a single IC, saving PCB area in dense headend chassis. The 3V single-supply operation also simplifies power-tree design in always-on headend infrastructure.
Рекомендуется
Software Defined Radio (SDR) Receiver
Software-defined radio platforms need flexible ADCs that capture wide IF bandwidths while keeping power low. The LTC2292CUP's 70 MHz analog input bandwidth lets it digitize HF and VHF signals directly in the second or third Nyquist zone at 40 Msps, supporting receiver architectures from amateur radio to military SDR. Dual channels permit simultaneous I/Q sampling without quadrature calibration drift, while 71 dB SNR preserves receiver sensitivity. The QFN-64 small footprint and 235 mW dissipation suit portable manpack and handheld SDR designs.
Рекомендуется
Multi-Channel Data Acquisition System
Industrial data-acquisition systems digitizing multiple analog signals from sensors, encoders, or process-control loops can use multiple LTC2292CUPs in parallel because each IC provides two 12-bit 40 Msps channels. The exposed-pad QFN-64 package and 235 mW dissipation per dual channel keep thermal density manageable in multi-DAQ cards with 16 or more channels. The selectable 1 Vp-p or 2 Vp-p input range accommodates both low-level sensor outputs and larger industrial signal swings directly, eliminating external attenuators. LVDS output mode simplifies routing across large PCBs to FPGAs.
Рекомендуется
RF Power Amplifier Digital Pre-Distortion Feedback
Cellular basestation digital pre-distortion (DPD) systems require accurate feedback ADCs to capture the output spectrum of the RF power amplifier so the linearization algorithm can cancel intermodulation distortion. The LTC2292CUP's 85 dB SFDR at 70 MHz and 110 dB channel-to-channel isolation enable precise PA output sampling at the DPD observation path, supporting ACLR improvement of 15 to 20 dB in typical DPD implementations. Two channels per chip allow capture of both forward and reverse path signals. The 40 Msps rate covers most sub-6 GHz DPD observation bands at baseband.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LTC2292CUP — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LTC2291CUP | LTC2293CUP | LTC2282CUP | LTC2287CUP | LTC2280CUP | LTC2221CUP |
|---|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | QFN-64 (UP, 9x9 mm) | QFN-64 (UP, 9x9 mm) - same | QFN-64 (UP, 9x9 mm) - same | QFN-64 (UP, 9x9 mm) - same | QFN-64 (UP, 9x9 mm) - same | QFN-64 (UP, 9x9 mm) - same | QFN-64 (UP, 9x9 mm) - same |
| Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 | 1 (single-channel) |
| Sample Rate | 40 Msps | 25 Msps | 65 Msps | 65 Msps | 40 Msps | 10 Msps | 135 Msps |
| Power Dissipation | 235 mW | 150 mW | 400 mW | 350 mW | 240 mW | 75 mW | 425 mW |
| SNR (Nyquist) | 71.3 dB | 71.5 dB | 71 dB | 70 dB | 71 dB | 72 dB | 68 dB |
| Supply Voltage | 2.5 V to 3.4 V | 2.5 V to 3.4 V | 2.5 V to 3.4 V | 2.5 V to 3.4 V | 2.5 V to 3.4 V | 2.5 V to 3.4 V | 2.5 V to 3.4 V |
| Approx. 1k Price | $13.42 | $11.50 | $18.95 | $17.80 | $14.10 | $9.20 | $24.50 |
Ключевые отличия
- Lowest power dissipation among dual 12-bit 40 Msps 3V ADCs in this footprint (против LTC2293CUP)
- Pin-compatible dual-channel upgrade/downgrade path (против LTC2291CUP and LTC2293CUP)
- Dual simultaneous-sampling channels in one IC (против LTC2221CUP)
Заметки по проектированию
Solder the exposed pad (EP) of the QFN-64 package to a continuous inner ground plane and stitch at least 9 thermal vias (0.3 mm hole, 0.5 mm pitch) under the pad for proper thermal relief. Without the EP soldered, theta_JA rises above 60 C/W and the 235 mW dissipation causes a junction temperature rise of more than 30 C. Place input and reference decoupling capacitors (REFT, REFB, COM, VREF) within 2 mm of their respective pins using 0.1 uF X7R ceramic capacitors. The analog (AVDD) and digital (OVDD) supplies should be filtered separately with ferrite beads to prevent digital switching noise from coupling back into the analog front end.
Drive the analog inputs differentially through a wideband ADC driver such as the AD8138 or AD8021 for optimal SFDR. Use 100 ohm differential transmission-line termination at the ADC inputs and route the AIN+/AIN- traces as a length-matched 50 ohm single-ended pair (100 ohm differential) to maintain good common-mode rejection. Keep the analog input traces away from digital output traces (D0-D11) and clock lines to avoid coupling digital noise into the analog front end. The clock traces (CLK+/CLK-) should also be routed as a 100 ohm differential pair and kept short to limit jitter.
Use a low-noise LDO such as the ADP3338 or ADP150 to supply AVDD, not a switching regulator, because the LTC2292CUP noise performance degrades with noisy supplies. The 235 mW dissipation at 3V requires about 78 mA on the AVDD pin; budget 100 mA for the LDO to provide margin. Add a 10 uF tantalum or ceramic bulk capacitor plus a 0.1 uF ceramic decoupling capacitor directly at each AVDD pin. The OVDD pin can be supplied by the digital 3V rail but should also be locally decoupled; keep its trace impedance low to avoid digital rail collapse during LVDS output switching.
Do not operate the LTC2292CUP above 3.4 V AVDD - the absolute maximum supply is 3.6 V and over-voltage will permanently damage the input ESD structures. The clock duty cycle must be between 20% and 80%; although the internal duty-cycle stabilizer handles a wide range, signals outside this range cause jitter-induced SNR degradation. Apply the AVDD supply before or simultaneously with the clock to avoid latch-up; never leave the analog inputs floating - tie them to COM through TIE_HI pins or to a defined DC voltage. Finally, in CMOS mode the OE pin must be driven low for normal operation; leaving it floating causes intermittent high-impedance output behavior.
Информация о соответствии
RoHS compliant per Analog Devices product page (#PBF suffix indicates lead-free, Pb-free matte-tin finish). The C grade suffix denotes 0C to +70C commercial operating range; the I grade (LTC2292IUP) extends to -40C to +85C industrial. Not AEC-Q100 qualified - this is a commercial-grade ADC for non-automotive applications.
