LTC2321CUFD-12 - Dual 12-Bit+Sign 2Msps SAR ADC | ADI
Артикул: LTC2321CUFD-12 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $8.95 | $8,95 |
| 10 | $8.2 | $82,00 |
| 100 | $7.45 | $745,00 |
| 500 | $6.8 | $3.400,00 |
| 1.000 | $6.1 | $6.100,00 |
LTC2321CUFD-12 Обзор
A successive-approximation-register (SAR) ADC is a precision converter architecture that performs a binary search on the analog input each conversion cycle, converting in a single clock step per bit (N+1 clocks for an N-bit result). Compared with sigma-delta and pipeline architectures, SAR converters offer deterministic latency, excellent DC linearity, low power consumption, and no pipeline delay, which makes them the preferred topology for multiplexed data acquisition, control loops, and multi-phase power monitoring where time-domain accuracy matters as much as raw sample rate.
The LTC2321-12 family integrates a precision internal reference and reference buffer, two high-bandwidth differential track-and-hold front ends, and a flexible CMOS/ LVDS-compatible serial LVDS interface. The differential inputs accept rail-to-rail common-mode swings, allowing the ADC to digitize signals riding on a wide range of DC bias points. An external reference option is also supported. The wide common-mode range eliminates the need for level-shifting op-amps ahead of the ADC in many industrial and instrumentation designs.
Designed for low noise and high dynamic performance, the LTC2321CUFD-12 targets demanding applications such as industrial process control, multi-phase motor current sensing, high-speed data acquisition systems, medical imaging front ends, and ATE (automatic test equipment) signal capture. The dual simultaneous-sampling channels are particularly valuable in three-phase power monitoring, where two phase currents must be sampled at the exact same instant to compute instantaneous power without phase-skew error.
When designing with this ADC, place the analog input RC network as close as possible to the IN+ / IN- pins to minimize charge kickback, and follow the manufacturer's recommended reference decoupling scheme. Use a low-jitter LVDS clock source for the conversion clock to avoid degrading SNR. The internal reference settles in a few milliseconds after power-up - allow adequate wake-up time before triggering conversions.
Аналоги без доработки для LTC2321CUFD-12 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LTC2321CUFD-12 (тот же форм-фактор и посадочное место) — отличается по Internal Reference, Number of Channels, Package, Resolution, Differential Input Range.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LTC2321IUFD-12
✅ Прямая замена✓ В наличии
$9.66 / шт.
Открыть даташит →LTC2321HUFD-12
✅ Прямая замена✓ В наличии
$5.62 / шт.
Открыть даташит →LTC2321CUFD-12#PBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2321CUFD-12#TRPBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2323CUFD-12
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2321CUFD-12 Максимальные параметры и электрические характеристики
| Разрешение | 12 bits + sign |
| Number of Channels | 2 (simultaneous sampling) |
| Sampling Rate (per channel) | 2 Msps |
| Architecture | SAR (Successive Approximation Register) |
| Input Type | Differential |
| Differential Input Range | 8 Vp-p |
| Напряжение питания | 3.3 V or 5 V single supply |
| Input Common-Mode Range | Wide (rail-to-rail capable) |
| Internal Reference | Yes (precision, with buffer) |
| Digital Interface | Serial LVDS / CMOS compatible |
| Корпус | 28-pin QFN (4 mm x 5 mm) |
| Рабочая температура | 0C to +70C (C grade) |
| Статус RoHS | Compliant |
| Lead-Free | Yes (PBF suffix) |
| AEC-Q100 Qualified | No |
Конфигурация выводов LTC2321CUFD-12
| Контакт 1 | GND — Ground |
| Контакт 2 | IN1+ — Channel 1 differential input, positive |
| Контакт 3 | IN1- — Channel 1 differential input, negative |
| Контакт 4 | REF — Reference voltage pin |
| Контакт 5 | REFOUT — Internal reference output |
| Контакт 6 | GND — Ground |
| Контакт 7 | VDD — Analog 3.3V / 5V supply |
| Контакт 8 | GND — Ground |
| Контакт 9 | OVDD — Digital interface supply |
| Контакт 10 | GND — Ground |
| Контакт 11 | CLK+ — Conversion clock, positive (LVDS) |
| Контакт 12 | CLK- — Conversion clock, negative (LVDS) |
| Контакт 13 | CNV+ — Convert / start, positive (LVDS) |
| Контакт 14 | CNV- — Convert / start, negative (LVDS) |
| Контакт 15 | GND — Ground |
| Контакт 16 | SDO+ — Serial data output, positive (LVDS) |
| Контакт 17 | SDO- — Serial data output, negative (LVDS) |
| Контакт 18 | SCK+ — Serial clock output, positive (LVDS) |
| Контакт 19 | SCK- — Serial clock output, negative (LVDS) |
| Контакт 20 | SDI+ — Serial data input, positive (LVDS, daisy chain) |
| Контакт 21 | SDI- — Serial data input, negative (LVDS, daisy chain) |
| Контакт 22 | BUSY — Conversion busy indicator |
| Контакт 23 | GND — Ground |
| Контакт 24 | IN2+ — Channel 2 differential input, positive |
| Контакт 25 | IN2- — Channel 2 differential input, negative |
| Контакт 26 | GND — Ground |
| Контакт 27 | VDD — Analog 3.3V / 5V supply |
| Контакт 28 | GND — Ground |
Типичное применение
LTC2321CUFD-12 подходит для 6 применениеs: Multi-Phase Motor Current Sensing, Industrial Process Control Data Acquisition, Power Quality and Energy Metering, Medical Imaging Front End, Automatic Test Equipment (ATE) Signal Capture, Vibration and Acoustic Analysis.
Multi-Phase Motor Current Sensing
The LTC2321CUFD-12 is a strong fit for multi-phase motor current sensing because its two channels sample at exactly the same instant (true simultaneous sampling), eliminating the phase-skew error that would otherwise corrupt instantaneous power calculation. Each 12-bit + sign channel at 2 Msps easily digitizes PWM-current waveforms in 50-200 kHz motor drives, while the 8 Vp-p differential input swing interfaces directly to high-side or low-side current-shunt amplifier outputs. Wide common-mode range tolerates the large dv/dt transients typical of MOSFET half-bridges without input saturation.
Рекомендуется
Industrial Process Control Data Acquisition
In industrial process-control and factory-automation systems, the LTC2321CUFD-12 provides two fast, low-latency analog inputs for digitizing sensor signals such as load-cell outputs, pressure transducers, and valve-position feedback. The SAR architecture delivers deterministic latency, which is critical when the digitized result is fed back into a PID control loop in real time. The wide common-mode range allows the part to accept signals riding on different grounds or bias levels without level-shifting, simplifying the analog front-end in distributed I/O modules.
Рекомендуется
Power Quality and Energy Metering
Three-phase power-quality analyzers and smart energy meters use the LTC2321CUFD-12 to digitize voltage and current waveforms simultaneously on multiple phases. The 2 Msps per channel sample rate comfortably captures harmonic content up to the 40th harmonic of a 50/60 Hz mains, supporting THD and individual-harmonic analysis per IEC 61000-4-7. The 12-bit + sign dynamic range resolves both the fundamental and low-order harmonics with adequate SNR, while the wide common-mode range directly accepts the scaled output of voltage-divider networks used on 480 V or higher AC lines.
Рекомендуется
Medical Imaging Front End
Ultrasound and other medical imaging front-ends use the LTC2321CUFD-12 to digitize time-gain compensated (TGC) receive signals from piezoelectric transducer arrays. The 2 Msps simultaneous dual-channel conversion captures two adjacent channels of an aperture at the same moment, preserving phase coherence needed for beamforming. The wide input common-mode range allows AC coupling of TGC outputs without DC biasing networks, while the low noise floor of the SAR front-end preserves small-signal dynamic range - directly improving the achievable image SNR.
Рекомендуется
Automatic Test Equipment (ATE) Signal Capture
In ATE pin-electronics and mixed-signal test systems, the LTC2321CUFD-12 functions as a high-throughput digitizer for measuring DUT (device-under-test) analog responses with deterministic latency. Two simultaneous 2 Msps channels let a single IC capture both the stimulus and the response in lockstep, or two channels of a differential stimulus signal, without introducing sampling skew. The wide common-mode range accepts a wide range of DUT signal levels without front-end attenuation networks. SAR architecture eliminates the latency variation seen in pipeline ADCs, simplifying stimulus-response timing analysis.
Рекомендуется
Vibration and Acoustic Analysis
MEMS microphone arrays, vibration sensors, and acoustic emission analyzers use the LTC2321CUFD-12 to digitize two channels of audio-bandwidth data simultaneously, enabling accurate cross-correlation and phase analysis. The 2 Msps per channel rate is well above the Nyquist requirement for 20 kHz audio and most mechanical-vibration bands. SAR architecture provides glitch-free, deterministic single-shot capture of transient events, which is essential for capturing impact or fault signatures. Wide common-mode range accommodates the bias output of integrated MEMS pre-amplifiers.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LTC2321CUFD-12 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LTC2321IUFD-12 | LTC2321HUFD-12 | LTC2321CUFD-12#PBF | LTC2321CUFD-12#TRPBF | LTC2323CUFD-12 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-pin QFN (4x5 mm) | 28-pin QFN (4x5 mm) - same | 28-pin QFN (4x5 mm) - same | 28-pin QFN (4x5 mm) - same | 28-pin QFN (4x5 mm) - same | 28-pin QFN (4x5 mm) - same |
| Resolution | 12-bit + sign | 12-bit + sign | 12-bit + sign | 12-bit + sign | 12-bit + sign | 12-bit + sign |
| Channels | 2 simultaneous | 2 simultaneous | 2 simultaneous | 2 simultaneous | 2 simultaneous | 8 multiplexed (sequential) |
| Sample Rate (per channel) | 2 Msps | 2 Msps | 2 Msps | 2 Msps | 2 Msps | 2 Msps aggregate |
| Operating Temperature | 0C to +70C (C grade) | -40C to +85C (I grade) | -40C to +125C (H grade) | 0C to +70C | 0C to +70C | 0C to +70C |
| Differential Input Range | 8 Vp-p | 8 Vp-p | 8 Vp-p | 8 Vp-p | 8 Vp-p | 8 Vp-p |
| 1-piece Price (USD, as of 2026-10-13) | 8.95 | approximately 9.50 | approximately 11.20 | 8.95 (same die, PBF suffix) | 8.95 (T&R packaging) | approximately 7.60 |
Ключевые отличия
- True dual simultaneous-sampling channels in 28-QFN (против LTC2323CUFD-12 (8-channel multiplexed))
- Wide 8 Vp-p differential input range with rail-to-rail common-mode (против LTC2314HTS8-14 (lower input swing))
- SAR architecture with deterministic latency (против Pipeline ADCs (e.g., AD9228 family))
Заметки по проектированию
Place the differential RC network (typically 20 ohm series and 47 pF to GND on each input) directly at the IN+ / IN- pins to absorb charge kickback from the internal sampling capacitor. Route IN+ and IN- as a tightly coupled differential pair on the top layer with a continuous ground plane underneath - any mismatch in trace length translates directly into common-mode-to-differential conversion that degrades SNR. The QFN exposed pad must be soldered to a ground copper pour with at least 4 thermal vias for low thermal impedance.
Keep the analog section (inputs, reference, AVDD) physically separated from the LVDS digital section (CLK, CNV, SDO, SCK, SDI) on the PCB. Use separate ground regions joined only at a single point, or split the GND layer into analog and digital halves stitched together near the ADC. The LVDS signals should be 100 ohm differential microstrip with matched length (+/- 5 mil) and DC-balanced termination at the receiver.
Do not apply a noisy, high-impedance clock to the CLK+/CLK- pins - clock jitter directly degrades SNR. Use a low-jitter LVDS clock source (jitter under 5 ps RMS preferred for full 12-bit performance). The wide common-mode input range is a feature, not an excuse to skip anti-alias filtering; always place a properly sized differential RC anti-alias filter ahead of the inputs to prevent out-of-band noise from aliasing into the passband.
Информация о соответствии
PBF suffix denotes lead-free / RoHS compliant. C-grade temperature range (0C to +70C) is commercial; not AEC-Q100 qualified. Not applicable for automotive.
