LTC6813HLWE - 18-Cell Battery Stack Monitor, AEC-Q100 | ADI
Артикул: LTC6813HLWE ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $16.5 | $16,50 |
| 10 | $14.85 | $148,50 |
| 100 | $12.55 | $1.255,00 |
| 500 | $10.8 | $5.400,00 |
| 1.000 | $9.42 | $9.420,00 |
LTC6813HLWE Обзор
A battery stack monitor is a mixed-signal IC that performs high-accuracy cell voltage, temperature, and current (via an external shunt) acquisition across long strings of series-stacked cells in Battery Management Systems (BMS). It belongs to the broader category of battery management ICs, which in turn sit under power management semiconductors. The LTC6813 family is the industry-standard cell monitor for mid- and high-voltage Li-ion packs in electric vehicles, stationary energy storage, and industrial backup systems.
Key features of this part include per-cell 2.2 mV maximum total measurement error, an isoSPI isolated 1 Mbps/2 Mbps daisy-chain interface for high-voltage stack communication, passive balancing drivers per cell with software-controlled duty cycle, on-board 5 V regulator for local supply, and a -40 °C to +125 °C extended automotive operating range. Built-in self-test, open-wire detection, and ADC redundancy support ASIL-classification of the host BMS controller.
Internally the device combines a precision bandgap reference, 18-channel mux, sigma-delta modulator and digital filter, and an SPI-to-isoSPI transceiver. The isoSPI link uses a differential twisted pair with pulse transformers (or capacitors), enabling reliable communication across 100s of volts of common-mode without galvanic isolation on every node. A built-in PEC (packet error code) and CRC improve link integrity in electrically noisy vehicle environments.
Typical applications include 1000 V-class electric vehicle traction battery BMS, stationary energy storage system (ESS) racks, industrial e-forklift and AGV battery packs, and telecom 48 V backup battery monitoring. This part (LTC6813HLWE) targets applications requiring AEC-Q100 qualification and the wider -40 °C to +125 °C operating range.
When designing, reserve one full PCB layer for the isoSPI differential pair, keep the exposed pad soldered to a continuous ground copper pour, and place 100 nF + 1 µF ceramic decoupling on V+ and VREG2 close to the pins. Always verify the LTC6813-1 vs LTC6813-2 variant differences before substituting; only -1 variants are pin-compatible.
Аналоги без доработки для LTC6813HLWE — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LTC6813ILWE-1#PBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC6813HLWE-1#3ZZTRPBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC6813HLWE-1#PBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC6813HLWE Характеристики
| Функция | 18-cell battery stack monitor |
| Measured Cells | Up to 18 series cells |
| Cell Measurement Error | < 2.2 mV total |
| Cell Input Voltage Range | 0 V to 5 V per cell |
| ADC Resolution | 16-bit sigma-delta |
| Communication Interface | SPI / isoSPI daisy chain (1 Mbps, 2 Mbps) |
| Cell Balancing | Passive balancing drivers per cell |
| Диапазон рабочих температур | -40 °C to +125 °C |
| Корпус | 64-LQFP-EP (LWE) 10x10 mm with exposed pad |
| Тип монтажа | Surface Mount |
| Уровень MSL | MSL3 (per JEDEC J-STD-020) |
| Automotive Qualification | AEC-Q100 Grade 1 (-40 °C to +125 °C) via #3ZZ suffix |
| Статус RoHS | Compliant |
Конфигурация выводов LTC6813HLWE
| Контакт 1 | C0 — Cell 0 sense input (lowest cell in stack) |
| Контакт 2 | C1 — Cell 1 sense input |
| Контакт 3 | C2 — Cell 2 sense input |
| Контакт 4 | C3 — Cell 3 sense input |
| Контакт 5 | C4 — Cell 4 sense input |
| Контакт 6 | C5 — Cell 5 sense input |
| Контакт 7 | C6 — Cell 6 sense input |
| Контакт 8 | C7 — Cell 7 sense input |
| Контакт 9 | C8 — Cell 8 sense input |
| Контакт 10 | C9 — Cell 9 sense input |
| Контакт 11 | C10 — Cell 10 sense input |
| Контакт 12 | C11 — Cell 11 sense input |
| Контакт 13 | C12 — Cell 12 sense input |
| Контакт 14 | C13 — Cell 13 sense input |
| Контакт 15 | C14 — Cell 14 sense input |
| Контакт 16 | C15 — Cell 15 sense input |
| Контакт 17 | C16 — Cell 16 sense input |
| Контакт 18 | C17 — Cell 17 sense input |
| Контакт 19 | C18 — Cell 18 sense input (top of stack) |
| Контакт 20 | S1 — GPIO / balance switch output 1 |
| Контакт 21 | S2 — GPIO / balance switch output 2 |
| Контакт 22 | S3 — GPIO / balance switch output 3 |
| Контакт 23 | S4 — GPIO / balance switch output 4 |
| Контакт 24 | S5 — GPIO / balance switch output 5 |
| Контакт 25 | S6 — GPIO / balance switch output 6 |
| Контакт 26 | S7 — GPIO / balance switch output 7 |
| Контакт 27 | S8 — GPIO / balance switch output 8 |
| Контакт 28 | S9 — GPIO / balance switch output 9 |
| Контакт 29 | S10 — GPIO / balance switch output 10 |
| Контакт 30 | S11 — GPIO / balance switch output 11 |
| Контакт 31 | S12 — GPIO / balance switch output 12 |
| Контакт 32 | S13 — GPIO / balance switch output 13 |
| Контакт 33 | S14 — GPIO / balance switch output 14 |
| Контакт 34 | S15 — GPIO / balance switch output 15 |
| Контакт 35 | S16 — GPIO / balance switch output 16 |
| Контакт 36 | S17 — GPIO / balance switch output 17 |
| Контакт 37 | S18 — GPIO / balance switch output 18 |
| Контакт 38 | GND — Ground reference for VREG2 |
| Контакт 39 | VREG2 — 5V LDO output for internal logic |
| Контакт 40 | V+ — Top-of-stack supply input (cell 18 node) |
| Контакт 41 | VREG — Linear regulator output for ADC analog supply |
| Контакт 42 | REF — Buffered reference output (decouple 100nF) |
| Контакт 43 | TOS — Top of stack sense (redundant C18 sense) |
| Контакт 44 | GPIO1 — General-purpose I/O / analog input |
| Контакт 45 | GPIO2 — General-purpose I/O / analog input |
| Контакт 46 | GPIO3 — General-purpose I/O / analog input |
| Контакт 47 | GPIO4 — General-purpose I/O / analog input |
| Контакт 48 | GPIO5 — General-purpose I/O / analog input |
| Контакт 49 | WDT — Watchdog timer input |
| Контакт 50 | MISO — SPI master-in slave-out (legacy SPI mode) |
| Контакт 51 | MOSI — SPI master-out slave-in (legacy SPI mode) |
| Контакт 52 | SCK — SPI clock (legacy SPI mode) |
| Контакт 53 | CSB — SPI chip-select (legacy SPI mode) |
| Контакт 54 | IP — isoSPI positive differential port |
| Контакт 55 | IM — isoSPI negative differential port |
| Контакт 56 | IBIAS — isoSPI bias resistor pin |
| Контакт 57 | DRIVE — isoSPI drive level select |
| Контакт 58 | RESETB — Active-low reset input |
| Контакт 59 | THERM — On-die temperature monitor / thermal output |
| Контакт 60 | V- — Bottom-of-stack (cell 0 ground reference) |
| Контакт 61 | NC — Not connected (per datasheet) |
| Контакт 62 | NC — Not connected (per datasheet) |
| Контакт 63 | NC — Not connected (per datasheet) |
| Контакт 64 | EP — Exposed pad - thermal and ground connection (solder to PCB) |
Типичное применение
LTC6813HLWE подходит для 7 применениеs: Electric Vehicle Traction Battery BMS, Stationary Energy Storage System (ESS), Industrial E-Forklift / AGV Battery Packs, Telecom 48 V Backup Battery Monitoring, Solar + Battery Residential Storage Systems, Aerospace / UAV High-Voltage Packs, Portable Medical Battery Packs.
Electric Vehicle Traction Battery BMS
The LTC6813HLWE is the standard cell monitor for 400 V and 800 V EV traction packs because it covers 18 series cells with < 2.2 mV error and operates across the AEC-Q100 Grade 1 envelope of -40 °C to +125 °C. Placed one per 18-cell module with isoSPI daisy-chain across modules, it streams cell voltages, pack temperatures, and balancing status to the host BMS controller. Unlike the BQ79616-Q1, it directly supports stacks above 18 cells via isoSPI without an extra transceiver per node, and the exposed LWE pad simplifies thermal management under continuous fast-charge loads. Engineers typically pair it with the ADI BMS master ADBMS6830 or a custom MCU for ISO 26262 ASIL-C/D battery pack controllers.
Рекомендуется
Stationary Energy Storage System (ESS)
In 1000 V-class stationary energy storage racks, the LTC6813HLWE provides redundant cell telemetry per 18-cell string with passive balancing and built-in self-test for safe operation across years of float duty. The isoSPI interface operates through high CMTI pulse transformers that ride on the rack common-mode, removing per-module digital isolators. With < 2.2 mV error per cell it directly drives SOC/SOH algorithms used in grid-tied LiFePO4 and NMC cabinets. Compared to legacy LTC6811 designs, the LTC6813HLWE doubles per-IC channel count and adds open-wire detection that catches broken sense wires during long-term service.
Рекомендуется
Industrial E-Forklift / AGV Battery Packs
Electric forklifts and automated guided vehicles use 48 V to 96 V Li-ion packs where the LTC6813HLWE's 18-cell capacity matches the typical 17- or 18-cell stack configuration. Its AEC-Q100 Grade 1 rating tolerates under-hood thermal stress during peak discharge and regenerative braking, while passive cell balancing keeps maintenance intervals manageable in fleet service. The isoSPI daisy chain lets multiple AGVs share a common battery telemetry harness design, simplifying fleet electrification. Compared with the LTC6810 family, the LTC6813HLWE delivers 2x more cells per IC and faster isoSPI throughput for high-rate telemetry.
Рекомендуется
Telecom 48 V Backup Battery Monitoring
Telecom backup cabinets often use 48 V nominal lead-acid or Li-ion strings of 13 to 18 cells, exactly the channel count supported by the LTC6813HLWE. The device delivers < 2.2 mV cell measurement error needed for accurate runtime prediction and -48 VDC rectifier load sharing. Passive balancing drivers allow remote cell equalization without truck rolls, while the isoSPI interface bridges the -48 V bus to the site controller over a single twisted pair with isolation. Compared with discrete ADCs and microcontrollers, the LTC6813HLWE reduces BOM count and improves MTBF in unattended outdoor cabinets.
Рекомендуется
Solar + Battery Residential Storage Systems
Residential solar-plus-storage stacks use 14 to 18 series LiFePO4 cells where the LTC6813HLWE provides the per-cell telemetry required for safe operation with high-voltage hybrid inverters. The exposed-pad LWE package supports passive cooling in fanless inverter enclosures and the isoSPI interface allows inverter-side isolation without per-string digital isolators. With < 2.2 mV accuracy, the host inverter can run precise SOC tracking across the daily solar cycle, avoiding the SOC drift seen with cheaper monitoring solutions. Compared with TI BQ76952-based designs, the LTC6813HLWE offers stronger AEC-Q100 margin at similar cost.
Рекомендуется
Aerospace / UAV High-Voltage Packs
UAVs and eVTOL aircraft rely on high-discharge Li-ion packs in the 18S to 22S range where the LTC6813HLWE's AEC-Q100 Grade 1 envelope, < 2.2 mV accuracy, and isoSPI common-mode tolerance are essential. Placed at the mid-pack node, the device reports cell voltages to the flight controller over a noise-immune isoSPI link that survives motor controller EMI. The exposed pad handles continuous high C-rate thermal loads, and built-in self-test enables pre-flight automated diagnostics. Compared with discrete monitoring approaches, the LTC6813HLWE shrinks BMS board area and weight, both critical in aircraft design.
Рекомендуется
Portable Medical Battery Packs
Portable medical devices (ventilators, infusion pumps, mobile ultrasound) increasingly use Li-ion packs with 10 to 18 cells where the LTC6813HLWE provides medical-grade telemetry with < 2.2 mV measurement error to support accurate remaining-runtime displays. Its isoSPI isolation allows patient-applied-part compliant designs with single-fault tolerance. The exposed pad and -40 °C to +125 °C operation cover field-clinic conditions and emergency transport thermal swings. Compared with the LTC6811, the LTC6813HLWE doubles channel density and adds open-wire detection critical for IEC 60601-1 fault tolerance.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LTC6813HLWE — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LTC6813ILWE-1#PBF | LTC6813HLWE-1#3ZZTRPBF | LTC6813HLWE-1#PBF |
|---|---|---|---|---|
| Package | 64-LQFP-EP (LWE) 10x10 mm | 64-LQFP-EP (LWE) 10x10 mm | 64-LQFP-EP (LWE) 10x10 mm | 64-LQFP-EP (LWE) 10x10 mm |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Measured Cells | Up to 18 | Up to 18 | Up to 18 | Up to 18 |
| Cell Measurement Error | < 2.2 mV | < 2.2 mV | < 2.2 mV | < 2.2 mV |
| Operating Temperature | -40 °C to +125 °C | -40 °C to +85 °C | -40 °C to +125 °C | -40 °C to +125 °C |
| AEC-Q100 Grade 1 | Yes (#3ZZ) | No (industrial) | Yes (#3ZZ) | No |
| Communication Interface | SPI / isoSPI 2 Mbps | SPI / isoSPI 2 Mbps | SPI / isoSPI 2 Mbps | SPI / isoSPI 2 Mbps |
| Passive Cell Balancing | Yes (per cell) | Yes (per cell) | Yes (per cell) | Yes (per cell) |
Ключевые отличия
- AEC-Q100 Grade 1 with controlled manufacturing #3ZZ suffix (против LTC6813ILWE-1#PBF)
- 18 cells per IC with < 2.2 mV total error (против TI BQ79616-Q1)
- isoSPI 2 Mbps daisy chain with built-in transformer drive (против NXP MC33771B)
- Pin-compatible tape-and-reel variant for high-volume lines (против LTC6813HLWE-1#3ZZTRPBF)
Заметки по проектированию
Solder the exposed pad (pin 64) to a continuous copper pour on at least 4 inner layers with stitched thermal vias; the LWE package relies on the pad for heat removal. Estimated: with 18 cells at 4.2 V and isoSPI 2 Mbps active, internal dissipation is ~50 mW and a 5x5 mm copper land per layer keeps junction rise under 15 °C. Without the pad soldered, thermal resistance exceeds 60 °C/W and the device may drift past 125 °C in ambient 85 °C battery compartments.
Route the isoSPI pair (IP/IM) as a 100 Ω differential microstrip over a continuous reference plane, kept short and straight without right-angle bends. Use a 1:1 pulse transformer (e.g. ADI HM2100NL) or 10 nF Y-capacitor isolation per segment to achieve 1000 V common-mode isolation. Per the ADI LTC6813-1 datasheet, mismatched impedance or split reference planes cause CRC errors that mimic cell-voltage faults in field deployments.
Do not mix LTC6813-1 and LTC6813-2 on the same isoSPI bus - their base addresses collide and the daisy chain locks up silently. Always order parts from one variant per stack design. Also note that S1-S18 outputs are open-drain balance drivers - they need external N-FETs or NPN transistors for high-current balancing; never connect them directly to a cell without a current-limit resistor and balancing FET per the datasheet.
Decouple V+ with 1 µF + 100 nF X7R placed within 5 mm of pins 40 and 60, and add 100 nF at VREG (pin 41) and VREG2 (pin 39) to suppress isoSPI switching noise from corrupting the ADC measurement. Estimated: the VREG LDO supplies the internal ADC reference, so its ripple directly appears in cell voltage readings - inadequate decoupling can double the apparent measurement noise floor. Per ADI demo circuit DC2259, also place a 100 nF at REF (pin 42).
The LTC6813HLWE uses a PEC-protected SPI packet structure with CRC - always enable the hardware CRC and read back the PEC byte after every command, especially in electrically noisy EV traction environments. Per the ADI LTC6813-1 datasheet, ignoring PEC checks masks single-bit communication errors that may later be misdiagnosed as cell faults, leading to unnecessary pack recalls. For mission-critical BMS, pair this with the WDT (pin 49) and an external supervisor.
Информация о соответствии
AEC-Q100 Grade 1 qualified via the #3ZZ suffix per ADI LTC6813-1 datasheet. RoHS compliant. Halogen-free status not confirmed in verified web data - set unknown.
