M1AFS1500-1FG484K - 1.5M Gate Fusion FPGA | Microchip Technology
Артикул: M1AFS1500-1FG484K ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $1640.7 | $1.640,70 |
| 10 | $1530.5 | $15.305,00 |
| 100 | $1410.25 | $141.025,00 |
| 500 | $1285.3 | $642.650,00 |
| 1.000 | $1170.4 | $1.170.400,00 |
M1AFS1500-1FG484K Обзор
An FPGA (Field Programmable Gate Array) is an integrated circuit whose logic fabric can be reconfigured after manufacturing. In a mixed-signal FPGA like Fusion, the digital fabric is joined with analog front-end resources, so system designers can implement control logic, interface processing, and analog monitoring on one chip. This fusion of functions reduces component count and design time compared to separate MCU/FPGA plus ADC systems.
Key features include 1.5M gates on a 130nm flash process, 223 general-purpose I/O configurable for common standards, and an integrated analog front end for voltage/current/temperature monitoring. The M1AFS1500-1FG484K speed grade -1 supports a 1282.05 MHz internal frequency rating, while 276,480 SRAM bits are available for buffering and soft processor memories. Flash-based configuration is live at power-up, eliminating external boot memory.
The Fusion family uses an M1 prefix to denote mixed-signal FPGA variants, integrating large Flash memory blocks, clock generation and management circuitry, and configurable analog. This architecture allows a single M1AFS1500 to supervise power supplies, sequence rails, measure currents, and execute FPGA logic, replacing several discrete devices. As a 484-ball BGA, the device offers 223 edge-attached I/O arranged around the package for compact routing.
Typical applications include industrial motor control, power-supply management, medical monitoring, and communications infrastructure. In motor drives, the Fusion analog block senses phase currents and DC-bus voltage while the FPGA fabric generates PWM and performs fault logic. In power management, the same device sequences multiple rails and communicates PMBus telemetry.
Designers should supply the 1.5 V core with clean low-impedance decoupling and separate sensitive analog inputs from heavy switching digital I/O. Because the package is a 484 FBGA, controlled impedance PCB stack-up and via-in-pad fanout are recommended for dense designs.
This page aggregates DigiKey and Mouser source data, volume pricing context from LCSC, drop-in Fusion-family part comparisons, and board-level design notes that go beyond the manufacturer datasheet.
Аналоги без доработки для M1AFS1500-1FG484K — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с M1AFS1500-1FG484K (тот же форм-фактор и посадочное место) — отличается по Package, RoHS Status, Process Technology, System Gates, Core Supply Voltage.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
M1AFS1500-1FG484
✅ Прямая замена✓ В наличии
$1089.55 / шт.
Открыть даташит →M1AFS1500-1FGG484K
✅ Прямая замена✓ В наличии
$1560 / шт.
Открыть даташит →M1AFS1500-FG484K
✅ Прямая замена✓ В наличии
$1327.1 / шт.
Открыть даташит →M1AFS1500-1FG484I
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$402.06 / шт.
Открыть даташит →M1AFS1500-1FG484M
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
M1AFS1500-1FG484K Максимальные параметры и электрические характеристики
| Product Family | Fusion Mixed-Signal FPGA |
| System Gates | 1.5M |
| User I/O | 223 |
| SRAM Bits | 276480 |
| Корпус | 484-BGA (FBGA) |
| Core Voltage | 1.5 V |
| Process Technology | 130 nm |
| Max Internal Frequency | 1282.05 MHz |
| Тип монтажа | Surface Mount |
| Configuration Memory | Flash-based |
| Speed Grade | -1 |
| Datasheet Pages | 294 |
| Статус RoHS | unknown |
Руководство по цоколевке M1AFS1500-1FG484K в корпусе 484-bga (fbga)
Цоколевка для M1AFS1500-1FG484K (корпус 484-bga (fbga)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для M1AFS1500-1FG484K.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
M1AFS1500-1FG484K подходит для 6 применениеs: Industrial Motor Control, Power Supply Management and Sequencing, Medical Patient Monitoring, Communications Infrastructure, Smart Grid and Energy Monitoring, Aerospace and Defense Computing.
Industrial Motor Control
The M1AFS1500-1FG484K is well suited for industrial motor control because its Fusion analog front end can directly sense phase currents, DC-bus voltage, and temperature while the FPGA fabric executes PWM, commutation, and fault logic. With 223 user I/O and 1.5M system gates, a single device can handle a two-level or three-level inverter gate-driver interface and close the current loop without an external ADC. The integrated 276480 SRAM bits provide buffer space for encoder and resolver data. Designers should isolate the high-voltage power stage from the FPGA analog inputs and use optical isolation on gate-driver signals. This mixed-signal approach reduces board area and latency compared to a discrete MCU plus FPGA plus ADC solution.
Рекомендуется
Power Supply Management and Sequencing
Fusion FPGAs are specifically designed for power management by combining programmable logic with analog monitor channels and flash memory. The M1AFS1500-1FG484K can sequence multiple output rails, read output voltages and currents through the analog front end, and control power-good signals or PMBus telemetry from the FPGA fabric. The 1.5M gate density is enough for complex state-machine sequencing, fault logging, and brown-out detection. Compared to a discrete power-management controller, the Fusion device allows custom sequencing rules to be updated in the field. Use precision resistor dividers to map voltage margins into the ADC input range and place bypass capacitors close to every VDD and VDDPLL pin.
Рекомендуется
Medical Patient Monitoring
In medical patient monitoring, the M1AFS1500-1FG484K provides deterministic FPGA logic for data acquisition and preprocessing while its analog front end monitors auxiliary signals such as temperature and power integrity. The 276480 SRAM bits and 1.5M gates support digital filtering, heart-rate/event detection, and communication protocol engines. The 484-BGA package allows compact PCB implementations in bedside monitors and portable devices. For isolation and safety, designers should follow IEC 60601 creepage and clearance guidance, although this product page does not claim medical certification. Keep analog sensor traces short and separate from the digital clock network to preserve measurement accuracy. The flash-based nature of the device means firmware can be updated securely, but a careful power-loss handling strategy is recommended for patient-data integrity.
Рекомендуется
Communications Infrastructure
The M1AFS1500-1FG484K can serve in communications infrastructure, where designers use FPGA logic for protocol framing, interface bridging, and error checking. Its 223 I/O support multiple voltage standards, allowing connection to Ethernet PHYs, UART transceivers, and backplane logic. The embedded flash memory retains configuration immediately at power-up, reducing boot time in line cards that must become operational quickly. The Fusion analog front end can supervise line-card voltages and temperatures, feeding telemetry to a management processor. For high-speed serial interfaces that require transceivers, the M1AFS1500 does not include built-in multi-gigabit SerDes, so external PHYs or a different FPGA family may be needed. Keep clock generation circuits close to the FPGA and use on-chip PLLs as described in the datasheet.
Рекомендуется
Smart Grid and Energy Monitoring
For smart grid and energy monitoring, the M1AFS1500-1FG484K combines data acquisition, computation, and communication in one mixed-signal FPGA. The analog front end can measure voltage and current transducer outputs while the FPGA performs harmonic analysis, phase-angle calculation, and energy-accumulation logic. With 1.5M gates and 276480 SRAM bits, designers can implement multiple metering channels and a soft processor core on the same device. Flash-based configuration is advantageous in utility environments because the device wakes quickly and does not require external configuration memory. Isolation barriers are required between high-voltage sensing circuits and the FPGA I/O. This product page does not assert Energy Star or IEC 62053 certification; confirm power-quality accuracy with a calibrated test setup.
Рекомендуется
Aerospace and Defense Computing
The M1AFS1500-1FG484K is used in aerospace and defense systems where flash-based FPGA technology provides immunity to single-event upsets compared to SRAM-based FPGAs in many radiation environments, although radiation tolerance is not stated in the provided data. Its 1.5M gates and 223 I/O support mission data processing, telemetry, and interface conversion. The Fusion analog block can monitor power rails and temperatures of line-replaceable units. Designers should use the military-temperature suffix variant if the full military temperature range is required; the K-suffix part's exact range must be verified. The 484-BGA package is compatible with standard PCB assembly and conformal coating processes. For high-reliability programs, perform radiation testing and qualification according to the project's derating guidelines.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для M1AFS1500-1FG484K — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | M1AFS1500-1FG484 | M1AFS1500-1FGG484K | M1AFS1500-FG484K | M1AFS1500-2FG484K |
|---|---|---|---|---|---|
| Package | 484-BGA (FBGA) | 484-BGA (FBGA) - same | 484-BGA (FBGA) - same | 484-BGA (FBGA) - same | 484-BGA (FBGA) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| System Gates | 1.5M | 1.5M | 1.5M | 1.5M | 1.5M |
| User I/O | 223 | 223 | 223 | 223 | 223 |
| SRAM Bits | 276480 | 276480 | 276480 | 276480 | 276480 |
| Core Voltage | 1.5 V | 1.5 V | 1.5 V | 1.5 V | 1.5 V |
| Speed Grade | -1 | -1 | -1 | Standard (no speed suffix) | -2 (higher performance) |
| Temperature Grade Option | K suffix | Non-K suffix | K suffix | K suffix | K suffix |
Ключевые отличия
- Speed grade -1 with 1282.05 MHz internal frequency rating (против M1AFS1500-FG484K)
- Flash-based configuration with internal Flash memory blocks (против M1AFS1500-2FG484K)
- No verified cross-brand drop-in equivalent (против Cross-brand SRAM-based FPGAs)
Заметки по проектированию
Estimated: The M1AFS1500-1FG484K operates from a 1.5V core supply. Dynamic power depends on design utilization, clock frequency, and I/O toggling; use Microchip's Fusion Power Calculator for a project-specific figure. Place a 10uF bulk capacitor and 0.1uF ceramic capacitor near every core supply pin, and additional high-frequency 0.01uF caps directly under the BGA if space allows.
Estimated: Thermal performance of the 484-pin FBGA depends on PCB copper area, airflow, and ambient temperature. Get the exact theta-JA value from the Fusion datasheet before determining whether a heatsink or forced airflow is required. For a high-utilization 1.5M-gate design, add thermal vias under the exposed pad or package center to improve heat spreading into the ground plane.
Keep analog inputs to the Fusion analog front end physically separated from high-speed digital FPGA I/O. Use a solid ground reference under the analog section, route analog traces as differential pairs when the datasheet requires, and add a series ferrite bead on any analog supply derived from the digital rail. For the 484-BGA, use a 0.8mm or finer trace/space stack-up and fan out with microvias if the board density demands it.
Информация о соответствии
The provided web data does not include a RoHS/REACH compliance statement for M1AFS1500-1FG484K. The FGG package suffix generally indicates a lead-free/green finish, but the target FG-suffix part requires verification from Microchip.