M1AFS1500-1FG484K - 1.5M Gate Fusion FPGA | Microchip Technology
N.º de pieza: M1AFS1500-1FG484K ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $1640.7 | $1.640,70 |
| 10 | $1530.5 | $15.305,00 |
| 100 | $1410.25 | $141.025,00 |
| 500 | $1285.3 | $642.650,00 |
| 1.000 | $1170.4 | $1.170.400,00 |
M1AFS1500-1FG484K Descripción general
An FPGA (Field Programmable Gate Array) is an integrated circuit whose logic fabric can be reconfigured after manufacturing. In a mixed-signal FPGA like Fusion, the digital fabric is joined with analog front-end resources, so system designers can implement control logic, interface processing, and analog monitoring on one chip. This fusion of functions reduces component count and design time compared to separate MCU/FPGA plus ADC systems.
Key features include 1.5M gates on a 130nm flash process, 223 general-purpose I/O configurable for common standards, and an integrated analog front end for voltage/current/temperature monitoring. The M1AFS1500-1FG484K speed grade -1 supports a 1282.05 MHz internal frequency rating, while 276,480 SRAM bits are available for buffering and soft processor memories. Flash-based configuration is live at power-up, eliminating external boot memory.
The Fusion family uses an M1 prefix to denote mixed-signal FPGA variants, integrating large Flash memory blocks, clock generation and management circuitry, and configurable analog. This architecture allows a single M1AFS1500 to supervise power supplies, sequence rails, measure currents, and execute FPGA logic, replacing several discrete devices. As a 484-ball BGA, the device offers 223 edge-attached I/O arranged around the package for compact routing.
Typical applications include industrial motor control, power-supply management, medical monitoring, and communications infrastructure. In motor drives, the Fusion analog block senses phase currents and DC-bus voltage while the FPGA fabric generates PWM and performs fault logic. In power management, the same device sequences multiple rails and communicates PMBus telemetry.
Designers should supply the 1.5 V core with clean low-impedance decoupling and separate sensitive analog inputs from heavy switching digital I/O. Because the package is a 484 FBGA, controlled impedance PCB stack-up and via-in-pad fanout are recommended for dense designs.
This page aggregates DigiKey and Mouser source data, volume pricing context from LCSC, drop-in Fusion-family part comparisons, and board-level design notes that go beyond the manufacturer datasheet.
Alternativas directas para M1AFS1500-1FG484K — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con M1AFS1500-1FG484K (mismo factor de forma y huella) — difiere en Package, RoHS Status, Process Technology, System Gates, Core Supply Voltage.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
M1AFS1500-1FG484
✅ Sustitución directa✓ En stock
$1089.55 / unidad
Ver hoja de datos →M1AFS1500-1FGG484K
✅ Sustitución directa✓ En stock
$1560 / unidad
Ver hoja de datos →M1AFS1500-FG484K
✅ Sustitución directa✓ En stock
$1327.1 / unidad
Ver hoja de datos →M1AFS1500-1FG484I
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$402.06 / unidad
Ver hoja de datos →M1AFS1500-1FG484M
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
M1AFS1500-1FG484K Valores máximos y características eléctricas
| Product Family | Fusion Mixed-Signal FPGA |
| System Gates | 1.5M |
| User I/O | 223 |
| SRAM Bits | 276480 |
| Encapsulado | 484-BGA (FBGA) |
| Core Voltage | 1.5 V |
| Process Technology | 130 nm |
| Max Internal Frequency | 1282.05 MHz |
| Tipo de montaje | Surface Mount |
| Configuration Memory | Flash-based |
| Speed Grade | -1 |
| Datasheet Pages | 294 |
| Estado RoHS | unknown |
Guía de configuración de pines de M1AFS1500-1FG484K 484-bga (fbga)
Configuración de pines para M1AFS1500-1FG484K (encapsulado 484-bga (fbga)). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para M1AFS1500-1FG484K.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
M1AFS1500-1FG484K es adecuado para 6 aplicacións: Industrial Motor Control, Power Supply Management and Sequencing, Medical Patient Monitoring, Communications Infrastructure, Smart Grid and Energy Monitoring, Aerospace and Defense Computing.
Industrial Motor Control
The M1AFS1500-1FG484K is well suited for industrial motor control because its Fusion analog front end can directly sense phase currents, DC-bus voltage, and temperature while the FPGA fabric executes PWM, commutation, and fault logic. With 223 user I/O and 1.5M system gates, a single device can handle a two-level or three-level inverter gate-driver interface and close the current loop without an external ADC. The integrated 276480 SRAM bits provide buffer space for encoder and resolver data. Designers should isolate the high-voltage power stage from the FPGA analog inputs and use optical isolation on gate-driver signals. This mixed-signal approach reduces board area and latency compared to a discrete MCU plus FPGA plus ADC solution.
Recomendado
Power Supply Management and Sequencing
Fusion FPGAs are specifically designed for power management by combining programmable logic with analog monitor channels and flash memory. The M1AFS1500-1FG484K can sequence multiple output rails, read output voltages and currents through the analog front end, and control power-good signals or PMBus telemetry from the FPGA fabric. The 1.5M gate density is enough for complex state-machine sequencing, fault logging, and brown-out detection. Compared to a discrete power-management controller, the Fusion device allows custom sequencing rules to be updated in the field. Use precision resistor dividers to map voltage margins into the ADC input range and place bypass capacitors close to every VDD and VDDPLL pin.
Recomendado
Medical Patient Monitoring
In medical patient monitoring, the M1AFS1500-1FG484K provides deterministic FPGA logic for data acquisition and preprocessing while its analog front end monitors auxiliary signals such as temperature and power integrity. The 276480 SRAM bits and 1.5M gates support digital filtering, heart-rate/event detection, and communication protocol engines. The 484-BGA package allows compact PCB implementations in bedside monitors and portable devices. For isolation and safety, designers should follow IEC 60601 creepage and clearance guidance, although this product page does not claim medical certification. Keep analog sensor traces short and separate from the digital clock network to preserve measurement accuracy. The flash-based nature of the device means firmware can be updated securely, but a careful power-loss handling strategy is recommended for patient-data integrity.
Recomendado
Communications Infrastructure
The M1AFS1500-1FG484K can serve in communications infrastructure, where designers use FPGA logic for protocol framing, interface bridging, and error checking. Its 223 I/O support multiple voltage standards, allowing connection to Ethernet PHYs, UART transceivers, and backplane logic. The embedded flash memory retains configuration immediately at power-up, reducing boot time in line cards that must become operational quickly. The Fusion analog front end can supervise line-card voltages and temperatures, feeding telemetry to a management processor. For high-speed serial interfaces that require transceivers, the M1AFS1500 does not include built-in multi-gigabit SerDes, so external PHYs or a different FPGA family may be needed. Keep clock generation circuits close to the FPGA and use on-chip PLLs as described in the datasheet.
Recomendado
Smart Grid and Energy Monitoring
For smart grid and energy monitoring, the M1AFS1500-1FG484K combines data acquisition, computation, and communication in one mixed-signal FPGA. The analog front end can measure voltage and current transducer outputs while the FPGA performs harmonic analysis, phase-angle calculation, and energy-accumulation logic. With 1.5M gates and 276480 SRAM bits, designers can implement multiple metering channels and a soft processor core on the same device. Flash-based configuration is advantageous in utility environments because the device wakes quickly and does not require external configuration memory. Isolation barriers are required between high-voltage sensing circuits and the FPGA I/O. This product page does not assert Energy Star or IEC 62053 certification; confirm power-quality accuracy with a calibrated test setup.
Recomendado
Aerospace and Defense Computing
The M1AFS1500-1FG484K is used in aerospace and defense systems where flash-based FPGA technology provides immunity to single-event upsets compared to SRAM-based FPGAs in many radiation environments, although radiation tolerance is not stated in the provided data. Its 1.5M gates and 223 I/O support mission data processing, telemetry, and interface conversion. The Fusion analog block can monitor power rails and temperatures of line-replaceable units. Designers should use the military-temperature suffix variant if the full military temperature range is required; the K-suffix part's exact range must be verified. The 484-BGA package is compatible with standard PCB assembly and conformal coating processes. For high-reliability programs, perform radiation testing and qualification according to the project's derating guidelines.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para M1AFS1500-1FG484K — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | M1AFS1500-1FG484 | M1AFS1500-1FGG484K | M1AFS1500-FG484K | M1AFS1500-2FG484K |
|---|---|---|---|---|---|
| Package | 484-BGA (FBGA) | 484-BGA (FBGA) - same | 484-BGA (FBGA) - same | 484-BGA (FBGA) - same | 484-BGA (FBGA) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| System Gates | 1.5M | 1.5M | 1.5M | 1.5M | 1.5M |
| User I/O | 223 | 223 | 223 | 223 | 223 |
| SRAM Bits | 276480 | 276480 | 276480 | 276480 | 276480 |
| Core Voltage | 1.5 V | 1.5 V | 1.5 V | 1.5 V | 1.5 V |
| Speed Grade | -1 | -1 | -1 | Standard (no speed suffix) | -2 (higher performance) |
| Temperature Grade Option | K suffix | Non-K suffix | K suffix | K suffix | K suffix |
Diferenciadores clave
- Speed grade -1 with 1282.05 MHz internal frequency rating (frente a M1AFS1500-FG484K)
- Flash-based configuration with internal Flash memory blocks (frente a M1AFS1500-2FG484K)
- No verified cross-brand drop-in equivalent (frente a Cross-brand SRAM-based FPGAs)
Notas de diseño
Estimated: The M1AFS1500-1FG484K operates from a 1.5V core supply. Dynamic power depends on design utilization, clock frequency, and I/O toggling; use Microchip's Fusion Power Calculator for a project-specific figure. Place a 10uF bulk capacitor and 0.1uF ceramic capacitor near every core supply pin, and additional high-frequency 0.01uF caps directly under the BGA if space allows.
Estimated: Thermal performance of the 484-pin FBGA depends on PCB copper area, airflow, and ambient temperature. Get the exact theta-JA value from the Fusion datasheet before determining whether a heatsink or forced airflow is required. For a high-utilization 1.5M-gate design, add thermal vias under the exposed pad or package center to improve heat spreading into the ground plane.
Keep analog inputs to the Fusion analog front end physically separated from high-speed digital FPGA I/O. Use a solid ground reference under the analog section, route analog traces as differential pairs when the datasheet requires, and add a series ferrite bead on any analog supply derived from the digital rail. For the 484-BGA, use a 0.8mm or finer trace/space stack-up and fan out with microvias if the board density demands it.
Información de cumplimiento
The provided web data does not include a RoHS/REACH compliance statement for M1AFS1500-1FG484K. The FGG package suffix generally indicates a lead-free/green finish, but the target FG-suffix part requires verification from Microchip.