MAX1198ECM+TDG05 - Dual 8-Bit 100MSPS ADC, 3.3V | Analog Devices
Артикул: MAX1198ECM+TDG05 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $24.5 | $24,50 |
| 10 | $22.05 | $220,50 |
| 100 | $19.6 | $1.960,00 |
| 500 | $17.4 | $8.700,00 |
| 1.000 | $15.3 | $15.300,00 |
MAX1198ECM+TDG05 Обзор
An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts real-world analog voltages into discrete digital codes for processing by microcontrollers, DSPs, or FPGAs. The MAX1198 belongs to the high-speed, low-power dual pipeline ADC category within the data-converter hierarchy (ADC -> data converter -> signal chain IC -> mixed-signal semiconductor), and is typically used to digitize baseband I/Q or color-difference component signals in image and video pipelines.
Key differentiating features include 100 MSPS guaranteed sampling rate on both channels simultaneously, two fully differential wideband T/H front ends optimized for IF sampling, an internal 2.048 V precision reference that eliminates external reference components, CMOS-compatible parallel outputs for direct FPGA/ASIC connection, and an exposed thermal pad (EP) on the 48-TQFP package that lowers junction-to-ambient thermal resistance for reliable continuous operation.
Architecturally, the MAX1198 uses a pipelined multi-stage conversion core with internal digital error correction, allowing low-latency operation suitable for real-time signal acquisition. The internal reference is bandgap-derived and trimmed for low drift; combined with differential inputs and wideband T/H front ends, the ADC achieves ENOB and SFDR figures suitable for instrumentation, digital communication, and imaging applications.
Typical applications include CCD/CIS image sensor digitizers, digital oscilloscope front ends, IF/baseband sampling in communications receivers, medical imaging pre-processing, and portable test-and-measurement instruments. The wide 7 mm body keeps the part footprint compatible with dense multi-channel data acquisition cards.
When designing with this device, pay attention to analog input common-mode and differential drive impedance to maximize SFDR, and provide a solid ground plane plus local 0.1 uF + 10 uF decoupling near the AVDD pins. The exposed pad on the TQFP package must be soldered to the PCB ground plane to meet the datasheet thermal performance and ensure specified linearity.
This page synthesizes distributor pricing, drop-in alternatives drawn from Maxim family variants, and practical design notes not collected in the manufacturer datasheet alone.
Аналоги без доработки для MAX1198ECM+TDG05 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MAX1198ECM+TD
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX1198ECM+D
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX1198ECM
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX1180ECM
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX1198ECM+TDG05 Максимальные параметры и электрические характеристики
| Разрешение | 8 bit |
| Number of Channels | 2 (dual) |
| Частота дискретизации | 100 MSPS |
| Architecture | Pipelined |
| Input Type | Fully differential, wideband track-and-hold |
| Напряжение питания | 3.3 V (3.0 V to 3.6 V) |
| Power Consumption | 264 mW (typical) |
| Internal Reference | Yes (2.048 V) |
| Output Interface | Parallel CMOS-compatible |
| Number of Inputs | 2 |
| Number of ADC Cores | 2 |
| Корпус | 48-TQFP-EP (7x7 mm) |
| Рабочая температура | -40 C to +85 C (industrial) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
| Число выводов | 48 |
Конфигурация выводов MAX1198ECM+TDG05
| Контакт 1 | IN1A+ — Channel 1 positive differential analog input |
| Контакт 2 | IN1A- — Channel 1 negative differential analog input |
| Контакт 3 | COMA — Channel 1 common-mode voltage bypass |
| Контакт 4 | REFA — Channel 1 reference bypass |
| Контакт 5 | AVDD — Analog supply voltage (3.3 V) |
| Контакт 6 | AVSS — Analog ground |
| Контакт 7 | IN2A+ — Channel 2 positive differential analog input |
| Контакт 8 | IN2A- — Channel 2 negative differential analog input |
| Контакт 9 | COMB — Channel 2 common-mode voltage bypass |
| Контакт 10 | REFB — Channel 2 reference bypass |
| Контакт 11 | DRVDD — Digital output driver supply |
| Контакт 12 | DRVSS — Digital output driver ground |
| Контакт 13 | D0A — Channel 1 digital output bit 0 (LSB) |
| Контакт 14 | D1A — Channel 1 digital output bit 1 |
| Контакт 15 | D2A — Channel 1 digital output bit 2 |
| Контакт 16 | D3A — Channel 1 digital output bit 3 |
| Контакт 17 | D4A — Channel 1 digital output bit 4 |
| Контакт 18 | D5A — Channel 1 digital output bit 5 |
| Контакт 19 | D6A — Channel 1 digital output bit 6 |
| Контакт 20 | D7A — Channel 1 digital output bit 7 (MSB) |
| Контакт 21 | D0B — Channel 2 digital output bit 0 (LSB) |
| Контакт 22 | D1B — Channel 2 digital output bit 1 |
| Контакт 23 | D2B — Channel 2 digital output bit 2 |
| Контакт 24 | D3B — Channel 2 digital output bit 3 |
| Контакт 25 | D4B — Channel 2 digital output bit 4 |
| Контакт 26 | D5B — Channel 2 digital output bit 5 |
| Контакт 27 | D6B — Channel 2 digital output bit 6 |
| Контакт 28 | D7B — Channel 2 digital output bit 7 (MSB) |
| Контакт 29 | OEA — Channel 1 output enable |
| Контакт 30 | OEB — Channel 2 output enable |
| Контакт 31 | CLK — Conversion clock input |
| Контакт 32 | CLKDUTY — Clock duty-cycle adjust |
| Контакт 33 | REFP — Internal reference positive bypass |
| Контакт 34 | REFN — Internal reference negative bypass |
| Контакт 35 | REFOUT — Internal reference output (2.048 V) |
| Контакт 36 | REFIN — External reference input (bypass for internal ref) |
| Контакт 37 | PD — Power-down (active high) |
| Контакт 38 | RESET — Digital reset |
| Контакт 39 | T/B — Output mode select: top/bottom binary |
| Контакт 40 | GND — Digital ground |
| Контакт 41 | DVDD — Digital supply voltage (3.3 V) |
| Контакт 42 | DVSS — Digital ground |
| Контакт 43 | NC — Not connected (internally pulled to ground per datasheet) |
| Контакт 44 | NC — Not connected (internally pulled to ground per datasheet) |
| Контакт 45 | NC — Not connected (internally pulled to ground per datasheet) |
| Контакт 46 | NC — Not connected (internally pulled to ground per datasheet) |
| Контакт 47 | NC — Not connected (internally pulled to ground per datasheet) |
| Контакт 48 | NC — Not connected (internally pulled to ground per datasheet) |
| Контакт 49 | EP — Exposed thermal pad - solder to PCB ground |
Типичное применение
MAX1198ECM+TDG05 подходит для 6 применениеs: CCD / CIS Image Sensor Digitizer, IF / Baseband Sampling in Communications Receivers, Portable Digital Oscilloscope Input Channel, Ultrasound Beamformer Front-End, Industrial Data Acquisition Module, Radar / Lidar Pulse Capture.
CCD / CIS Image Sensor Digitizer
The MAX1198ECM+TDG05 fits CCD/CIS image sensor digitization because its two fully differential wideband T/H inputs simultaneously sample the two color-difference component outputs of CCD or CIS imagers at up to 100 MSPS per channel, capturing full-resolution video frames in a single pass. With 8-bit resolution and an internal 2.048 V reference, the part eliminates an external reference component, reducing BOM and PCB area for compact camera modules. Its 264 mW typical power at 3.3 V keeps thermal rise manageable in sealed optical assemblies. Placed between the CCD output drivers and the FPGA image pipeline, the ADC provides parallel CMOS data the FPGA can capture without an external serializer, simplifying the FPGA I/O budget versus LVDS-output ADCs.
Рекомендуется
IF / Baseband Sampling in Communications Receivers
The MAX1198ECM+TDG05 is suitable for IF/baseband sampling in communications receivers because its wideband differential track-and-hold can digitize intermediate-frequency signals up to approximately 100 MHz with 8-bit resolution, enabling direct-IF digitization that moves the ADC closer to the antenna. Its 3.3 V single-supply operation simplifies power-tree design in portable handset or base-station receiver cards, and the internal precision reference holds SFDR stable across temperature. With two channels, the part captures both I and Q simultaneously, supporting quadrature demodulation in software-defined radio and digital receiver architectures. Power dissipation at 264 mW is acceptable for chassis-mounted receiver cards with airflow.
Рекомендуется
Portable Digital Oscilloscope Input Channel
The MAX1198ECM+TDG05 is a strong fit for portable digital oscilloscope input channels where dual 100 MSPS conversion at 8-bit resolution enables 200 MSPS equivalent single-channel time-interleaved sampling when two ADCs are cascaded or for two simultaneous probe channels at full speed. The 48-TQFP-EP 7 mm x 7 mm package keeps the front-end compact, freeing PCB area for the FPGA capture memory and display driver. The exposed thermal pad lowers junction-to-ambient resistance, allowing continuous sampling without thermal shutdown in lab instruments. Its parallel CMOS outputs integrate directly with mid-range FPGAs used in entry-level oscilloscope designs without requiring an LVDS deserializer.
Рекомендуется
Ultrasound Beamformer Front-End
The MAX1198ECM+TDG05 supports ultrasound beamformer front ends because its dual-channel 100 MSPS conversion captures two adjacent transducer element signals in parallel, supporting phased-array beam steering in mid-range diagnostic ultrasound carts. The fully differential inputs reject common-mode noise from long coaxial probe cables, while the internal precision reference ensures channel-to-channel gain matching critical for accurate beamforming. Its 264 mW per channel power is acceptable for 32 to 64-channel carts with proper thermal design. Parallel CMOS outputs feed the FPGA delay-and-sum beamforming engine without serializer latency, enabling real-time imaging at clinically useful frame rates.
Рекомендуется
Industrial Data Acquisition Module
The MAX1198ECM+TDG05 suits industrial data acquisition modules because its dual 8-bit 100 MSPS conversion handles two high-speed sensor signals simultaneously, such as vibration and position feedback in servo drives. The wideband differential inputs reject industrial electrical noise common on factory floors, and the internal 2.048 V reference avoids calibration drift over industrial temperature ranges of -40 C to +85 C. Industrial-grade temperature rating and a small 48-TQFP-EP 7x7 mm footprint allow dense multi-channel acquisition cards in PLC and motion-control chassis. The parallel CMOS outputs interface directly with industrial FPGAs and microcontrollers for closed-loop control loops.
Рекомендуется
Radar / Lidar Pulse Capture
The MAX1198ECM+TDG05 captures radar and lidar return pulses because its dual 100 MSPS 8-bit conversion can digitize two baseband return channels at high sample rates, enabling accurate pulse-shape analysis in automotive and industrial ranging systems. The wideband differential T/H preserves fast-rising pulse edges, and the 3.3 V single-supply operation eases power-tree design in 12 V or 24 V vehicle systems after the front-end buck regulator. Two channels capture both the I and Q return paths in a coherent radar receiver, supporting Doppler velocity extraction in firmware. The 48-TQFP-EP package with exposed pad supports thermally demanding continuous-scan lidar applications.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX1198ECM+TDG05 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX1198ECM+TD | MAX1198ECM+D | MAX1198ECM | MAX1180ECM |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 48-TQFP-EP (7x7 mm) | 48-TQFP-EP (7x7 mm) - same | 48-TQFP-EP (7x7 mm) - same | 48-TQFP-EP (7x7 mm) - same | 48-TQFP-EP (7x7 mm) - same |
| Resolution | 8 bit | 8 bit | 8 bit | 8 bit | 10 bit (+25%) |
| Sampling Rate | 100 MSPS | 100 MSPS | 100 MSPS | 100 MSPS | 105 MSPS |
| Number of Channels | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Internal Reference | Yes (2.048 V) | Yes (2.048 V) | Yes (2.048 V) | Yes (2.048 V) | Yes |
| Input Type | Differential T/H | Differential T/H | Differential T/H | Differential T/H | Differential T/H |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Ключевые отличия
- Pin-compatible 10-bit upgrade path on same footprint (против MAX1180ECM)
- Integrated 2.048 V internal precision reference (против MAX1198ECM (no suffix))
- Dual fully differential wideband T/H on 48-TQFP-EP (против MAX1198ECM+TD)
Заметки по проектированию
Place 0.1 uF ceramic decoupling capacitors as close as possible to each AVDD, DVDD, and DRVDD pin, with a shared 10 uF bulk tantalum or ceramic capacitor on each supply rail. Use a solid uninterrupted ground plane under the ADC and avoid routing digital output traces beneath the analog input pins or the exposed thermal pad. The exposed pad (EP) on the 48-TQFP-EP MUST be soldered to the PCB ground plane with multiple thermal vias to meet specified AC electrical performance.
Drive the analog inputs with a fully differential source impedance below 100 ohm to preserve SFDR at 100 MSPS. Use controlled-impedance differential traces (typically 100 ohm differential) from the input driver to the INxA+/INxA- pins, and place the COMA and COMB common-mode bypass capacitors immediately adjacent to the IC. The CLK trace must be routed with 50 ohm controlled impedance and kept away from analog input traces to avoid coupling conversion-clock noise into the analog front end.
The MAX1198 N.C. pins are internally pulled to ground, which allows the part to be a drop-in replacement for the 10-bit MAX1180 per the manufacturer datasheet. If a customer requires 10-bit dynamic range, populating the MAX1180 in a MAX1198 socket or footprint provides an upgrade path without PCB rework. For 8-bit applications, both parts are interchangeable.
Estimated: at full 100 MSPS dual-channel operation with 3.3 V supply, the MAX1198ECM+TDG05 dissipates approximately 264 mW (per Analog Devices datasheet typical figure). On a 4-layer JEDEC-standard test PCB the junction-to-ambient theta_JA is approximately 35 C/W, yielding a junction temperature rise of roughly 9 C above ambient at room temperature. In sealed enclosures without airflow, derate by ensuring the EP is soldered to a sufficient ground copper area (>= 1 square inch) to keep junction temperature within the -40 C to +85 C industrial range. Do not exceed 3.6 V on AVDD/DVDD/DRVDD as permanent damage may result.
Информация о соответствии
RoHS compliant per distributor product listings. Not AEC-Q100 qualified - industrial temperature grade -40 C to +85 C.
