MAX232ACUE+T - 5V Dual RS-232 Transceiver | Analog Devices
Артикул: MAX232ACUE+T ✓ АктивенMAX232ACUE+T Обзор
An RS-232 transceiver is an interface IC within the broader hierarchy of interface semiconductors, serial communication devices, and data-conversion components. It combines transmit and receive functions in one package: outgoing logic signals pass through line drivers that provide RS-232-compatible levels, while incoming serial signals pass through receivers that convert RS-232 levels back to logic-compatible signals. Integrating both directions simplifies PCB layout in point-to-point serial links, industrial controllers, and service interfaces.
The primary identified features are two transmit channels, two receive channels, operation from a 5V supply, and a compact 16-pin TSSOP footprint. The MAX232ACUE+T uses the MAX232 family interface architecture and is intended for commercial-temperature equipment. Its gull-wing terminal arrangement supports conventional surface-mount assembly and inspection after soldering, while the 16-pin package provides a practical size reduction compared with larger through-hole implementations.
Technical suitability depends on the voltage levels, data rate, cable length, grounding method, and protection strategy of the connected RS-232 port. Because RS-232 uses single-ended signaling and negative-going voltage levels, the interface must be evaluated together with its charge-pump capacitors, supply bypass, connector protection, and common-mode conditions. The manufacturer datasheet should be used for the complete pin-description table, recommended capacitor values, electrical limits, and operating conditions before layout release.
Typical uses include configuration and service ports on industrial equipment, serial links between controllers and peripheral modules, RS-232 test equipment, and legacy communications interfaces retained during product modernization. The device is especially useful where two full-duplex RS-232 channels are required but a larger multi-channel transceiver would be unnecessary. A design should still verify that the selected connector and cable environment match the electrical limits of the interface.
PCB layout is a central implementation consideration. Place the required charge-pump and bypass capacitors close to their associated pins, keep the RS-232 driver outputs away from sensitive analog or high-speed logic, and provide an appropriate chassis or signal-ground strategy at the connector. Add transient protection when the cable can be longer than the protected equipment area or exposed to industrial transients.
This page organizes the verified product identity, electrical requirements, pin-compatible replacement options, interface applications, and practical RS-232 layout guidance. It helps engineers move from MPN identification to footprint, replacement, and circuit-implementation checks while keeping the final design anchored to the manufacturer datasheet.
Аналоги без доработки для MAX232ACUE+T — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MAX232ACUE+T (тот же форм-фактор и посадочное место) — отличается по Interface Standard.
MAX232AEUE+
✅ Прямая заменаУточнить цену
Открыть даташит →MAX232CUE+
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MAX232CUE+T
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MAX232ACUE+
✅ Прямая заменаУточнить цену
Открыть даташит →MAX232ACUE+T Характеристики
| Product Type | RS-232 transceiver interface IC |
| Transmitter Count | 2 |
| Receiver Count | 2 |
| Напряжение питания | 5 V |
| Interface Standard | RS-232 |
| Package Type | TSSOP |
| Total Terminal Count | 16 |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Тип монтажа | Surface mount |
| Temperature Grade | Commercial |
| Driver and Receiver Configuration | 2/2 full RS-232 transceiver |
Руководство по цоколевке MAX232ACUE+T в корпусе rectangular
Цоколевка для MAX232ACUE+T (корпус rectangular). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для MAX232ACUE+T.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MAX232ACUE+T подходит для 6 применениеs: Industrial Controller Service Port, RS-232 Test and Measurement Equipment, Point-to-Point Serial Data Link, Serial Configuration and Diagnostics, Legacy Equipment Modernization, Data Acquisition and Control Module.
Industrial Controller Service Port
The MAX232ACUE+T fits industrial controller service ports that require two RS-232 channels for configuration, diagnostics, and production programming. Its two transmitters and two receivers provide bidirectional logic-to-RS-232 conversion in one 16-pin TSSOP package, reducing the number of separate interface devices and conserving board area. The 5V supply requirement integrates naturally with controller rails that already operate at that level. Place the charge-pump capacitors close to the IC and route each driver output directly toward its connector, keeping external switching nodes away from the receiver inputs. Use transient protection at the connector when the service cable can extend beyond the controlled equipment area.
Рекомендуется
RS-232 Test and Measurement Equipment
The MAX232ACUE+T is suitable for test and measurement equipment that must exchange commands and results through legacy RS-232 ports. Two driver channels support outbound control or measurement data, while two receiver channels accept instrument responses or operator commands. The 16-pin TSSOP package offers a compact surface-mount implementation, and the 5V-powered architecture fits instrument designs that already distribute a 5V rail. Keep the interface network close to the connector, provide a defined ground reference, and account for the RS-232 level shifts when selecting protection components or level translators elsewhere in the signal path.
Рекомендуется
Point-to-Point Serial Data Link
MAX232ACUE+T can serve as the interface at either end of a point-to-point RS-232 link between two digital controllers. The integrated dual-driver and dual-receiver arrangement supports two independent communication paths when the connected equipment exposes more than one RS-232 channel. Because the device changes voltage levels and signal polarity, the host logic can remain at ordinary CMOS-compatible levels while the cable carries RS-232 signals. Verify the maximum supported data rate and receiver threshold requirements in the manufacturer datasheet, and use a twisted-pair cable with the appropriate signal-ground connection for reliable operation.
Рекомендуется
Serial Configuration and Diagnostics
The MAX232ACUE+T is well suited to product configuration, boot-loader access, and diagnostic channels embedded in control systems. Two receivers allow a system to monitor command or status information, while two drivers permit responses and configuration data to reach the external host. Its 16-pin TSSOP package simplifies placement on densely populated control boards, while the 5V supply fits many mixed-signal systems. For robust field operation, isolate the logic side from cable transients with a suitable protection network and route the driver outputs away from sensitive analog inputs to minimize capacitive coupling.
Рекомендуется
Legacy Equipment Modernization
MAX232ACUE+T can preserve an existing RS-232 interface while modernizing the logic and power architecture around it. Equipment with a legacy service or data port can use the IC to retain connector-level compatibility without redesigning the external cable or host software. The commercial-temperature ordering code is appropriate for designs whose specified environmental range remains within its rating. During replacement, compare every pin in the manufacturer datasheet, especially enable, ground, charge-pump, and supply connections, and verify that the new board provides the required bypass and protection arrangements.
Рекомендуется
Data Acquisition and Control Module
The MAX232ACUE+T fits data-acquisition modules that communicate with a host computer over RS-232. Two transmit channels can carry commands and configuration data, while two receive channels can return measurements and status information. Using a dedicated interface IC keeps the RS-232 voltage translation away from sensitive acquisition circuitry and makes signal routing easier to review. Place the device near the serial connector when practical, maintain a short ground return, and separate the transmit routes from high-impedance sensor inputs to reduce noise pickup. Confirm the supported data rate and channel direction assignments in the manufacturer datasheet.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX232ACUE+T — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX232AEUE+ | MAX232CUE+ | MAX232CUE+T | MAX232ACUE+ |
|---|---|---|---|---|---|
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Transmitter Count | 2 | 2 | 2 | 2 | 2 |
| Receiver Count | 2 | 2 | 2 | 2 | 2 |
| Interface Standard | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Ключевые отличия
- Compact integration of two RS-232 channels (против MAX232EIPWR)
- Documented complete-replacement option (против MAX232AEUE+)
- Commercial-temperature ordering configuration (против MAX232CUE+T)
Заметки по проектированию
Place the MAX232ACUE+T charge-pump capacitors at the pins shown in the manufacturer pin-description table and keep each connection loop as short as practical. Use the recommended capacitance, tolerance, dielectric type, and voltage rating. Long capacitor traces add loop area and can reduce noise immunity. Route the RS-232 driver outputs directly toward their connector pins, and avoid placing them alongside sensitive receiver or analog inputs.
Do not treat the MAX232 family name as proof that every suffix has identical enable, shutdown, or temperature behavior. MAX232ACUE+T, MAX232AEUE+, and MAX232C-series variants may differ in ordering codes and operating classifications even when they use the same TSSOP footprint. Compare the complete manufacturer ordering table, pin description, absolute maximum ratings, and environmental requirements before approving a replacement.
RS-232 is a single-ended interface, so ground offset and cable-induced transients can affect receiver operation. Route the interface ground with the cable return, use a stable reference near the transceiver, and place appropriately rated protection at an exposed connector. Keep protection return current out of sensitive analog ground paths. Validate the completed design against the maximum data rate, receiver thresholds, and system-level EMC requirements.
Информация о соответствии
The product information identifies the MAX232ACUE+T as a commercial-temperature RS-232 interface IC but does not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. Request the current manufacturer material-compliance declaration for the exact ordering code.