MAX3221EAE+T - 3V RS-232 Transceiver | Analog Devices
Артикул: MAX3221EAE+T ✓ АктивенMAX3221EAE+T Обзор
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into logic levels. The MAX3221 belongs to the broader RS-232 interface, communication interface, and interface IC hierarchy. Its integrated charge-pump supply generates the bipolar voltage required by the RS-232 transmitter, allowing operation from a single low-voltage supply rather than a separate positive and negative power rail.
The MAX3221E family features automatic shutdown and wake-up behavior. When no valid signal is detected at the receiver inputs, the on-board power supply and drivers can shut down, reducing supply current to approximately 1 µA according to the manufacturer product information. This behavior is useful in battery-powered and intermittently connected equipment because the interface does not need to remain fully powered between communication sessions.
The E version adds enhanced electrostatic-discharge protection. The manufacturer lists ±15 kV ESD protection for the MAX3221E, while the MAX3221 product family is designed for EIA/TIA-232 and V.28/V.24 communications. The MAX3221E product page also identifies IEC 61000-4-2 ESD protection for the RS-232 pins. These ratings should be evaluated against the connector placement and system grounding strategy rather than treated as a substitute for external surge protection.
Typical uses include industrial serial-port equipment, point-of-sale terminals, data acquisition equipment, configuration interfaces, and legacy peripheral connectivity. The 16-pin SSOP footprint suits compact designs where space is constrained, although connector routing and exposed-charge-pump behavior still require careful PCB planning. The MAX3221E/MAX3223E/MAX3243E family is available from a 3 V supply, with the exact model selection determined by the required number of drivers and receivers.
Designers should follow the manufacturer’s recommended charge-pump capacitor connections, place the four external capacitors close to their associated pins, and route the RS-232 traces away from sensitive analog and high-speed digital paths. Receiver and driver enable functions provide local control, while AutoShutdown can reduce power when the remote device is disconnected. The MAX3221EAE+T is therefore best suited to compact, single-supply RS-232 links that require automatic power saving and improved ESD resilience.
This page combines the manufacturer family information with practical interface-selection guidance, package-specific implementation considerations, and qualified comparison options for engineers evaluating replacements for the MAX3221EAE+T.
Аналоги без доработки для MAX3221EAE+T — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MAX3221EAE+T (тот же форм-фактор и посадочное место) — отличается по ESD Protection, Product Type, Package, Supply Voltage Range, Interface Standard.
MAX3221EAE+
✅ Прямая заменаУточнить цену
Открыть даташит →MAX3221ECAE+T
✅ Прямая заменаУточнить цену
Открыть даташит →MAX3221ECAE+
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX3221IDB
✅ Прямая заменаУточнить цену
Открыть даташит →MAX3221EAE+TG1Z
✅ Прямая заменаУточнить цену
Открыть даташит →MAX3221EAE+T Характеристики
| Product Type | RS-232 transceiver |
| Number of Drivers | 1 driver |
| Number of Receivers | 1 receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Корпус | 16-pin SSOP |
| Тип монтажа | Surface mount |
| Shutdown Supply Current | Approximately 1 µA |
| ESD Protection | ±15 kV |
| ESD Standard | IEC 61000-4-2 |
| Communication Standard | EIA/TIA-232 |
| Supported V.28/V.24 Rates | V.28 and V.24 |
| Power Architecture | Single-supply charge-pump design |
| External Charge-Pump Capacitors | 4 capacitors |
| AutoShutdown Feature | Yes |
| Auto-Wakeup Feature | Yes |
| Driver Enable Control | Dedicated enable pin |
Руководство по цоколевке MAX3221EAE+T в корпусе 16-pin ssop
Цоколевка для MAX3221EAE+T (корпус 16-pin ssop). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для MAX3221EAE+T.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MAX3221EAE+T подходит для 6 применениеs: Industrial Serial-Port Control, Point-of-Sale Terminal Interface, Data-Acquisition Equipment, Legacy Peripheral Connectivity, Battery-Powered Service Terminal, Networked Equipment Management Port.
Industrial Serial-Port Control
The MAX3221EAE+T fits compact industrial controllers that must connect a logic-level serial controller to an RS-232 equipment port. Its 3 V to 5.5 V single-supply operation eliminates the need for a separate positive and negative transceiver rail, while the integrated charge pump supplies the required RS-232 levels. One driver and one receiver are sufficient for a point-to-point management or configuration link. AutoShutdown is valuable when the connected equipment spends substantial time idle because the family can reduce supply current to approximately 1 µA after receiver inputs cease detecting a valid signal. The ±15 kV ESD rating also strengthens the interface against charged cable and connector transients, although the final protection strategy must also account for ground offsets and external cable routing.
Рекомендуется
Point-of-Sale Terminal Interface
Point-of-sale equipment commonly retains RS-232 connections for receipt printers, scanners, scales, and service consoles. The MAX3221EAE+T provides the required line-driver and receiver functions in a compact 16-pin SSOP, allowing a controller board to use only a 3 V to 5.5 V supply. AutoShutdown reduces power when no valid receiver activity is present, which is advantageous in countertop systems that remain energized for long periods. The manufacturer identifies the MAX3221E family as compliant with EIA/TIA-232 requirements and provides enhanced ESD protection for exposed serial connections. Place the four external charge-pump capacitors close to their associated pins, observe the supply sequencing requirements, and keep the connector-side return path compact to reduce noise and ground-potential problems.
Рекомендуется
Data-Acquisition Equipment
The MAX3221EAE+T is appropriate for laboratory and industrial data-acquisition products that expose a legacy RS-232 configuration or command port. A single transceiver channel can carry an asynchronous serial command stream from the acquisition controller to a computer or service terminal. Operating from 3 V to 5.5 V permits the interface to share power with modern embedded systems while the charge-pump circuit creates the bipolar signal required for RS-232. Automatic shutdown and wake-up reduce energy use when no terminal is connected, and the 16-pin SSOP preserves board area. The E-version ESD protection is particularly relevant when the port is accessible through an external panel connector. Designers should still use the manufacturer’s reference layout and verify cable length, ground reference, and data-rate requirements against the complete device specifications.
Рекомендуется
Legacy Peripheral Connectivity
The MAX3221EAE+T bridges modern digital electronics and legacy peripherals that retain an RS-232 command interface. Examples include programmable instruments, access-control terminals, laboratory controllers, and service equipment. One transmitter and one receiver are sufficient for a basic bidirectional control channel, while the dedicated driver-enable and receiver-enable controls allow local management of the interface. Because the MAX3221E family supports operation from 3 V to 5.5 V, it can be integrated into systems that no longer provide the ±12 V supply commonly associated with older RS-232 implementations. The integrated charge pump removes that external bipolar supply requirement. For exposed installations, route the line and ground as a controlled pair and apply the manufacturer’s ESD and layout guidance at the connector entry.
Рекомендуется
Battery-Powered Service Terminal
A battery-powered service terminal can use MAX3221EAE+T AutoShutdown behavior to avoid wasting power on an inactive RS-232 connection. The MAX3221 family can reduce its supply current to approximately 1 µA when the receiver inputs do not sense a valid signal, then automatically resume operation when activity appears. This is useful in portable diagnostic equipment, field-service tools, and maintenance terminals that connect to equipment intermittently. The 3 V to 5.5 V operating range supports common portable supply architectures, and the 16-pin SSOP leaves room for a compact PCB. Designers should account for the logic levels used by the host controller, ensure the enable polarity is handled correctly, and confirm wake-up timing against the communication protocol before treating the low-power mode as a transparent power-management feature.
Рекомендуется
Networked Equipment Management Port
The MAX3221EAE+T can provide a dedicated RS-232 management channel on network appliances, test equipment, and embedded control systems. One port supports configuration loading, diagnostics, firmware commands, or basic status reporting without adding another transmitter and receiver channel to the board. The interface’s 3 V to 5.5 V operation allows it to use the same supply as common system logic, while the integrated charge pump generates the required RS-232 voltage internally. AutoShutdown helps manage power when the management port is idle, and the MAX3221E family’s ±15 kV ESD protection improves robustness at an exposed connector. The design should retain a defined signal ground, use controlled connector pin assignments, and separate the RS-232 routing from clocked digital and sensitive analog nets.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX3221EAE+T — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX3221EAE+ | MAX3221ECAE+T | MAX3221ECAE+ | MAX3221IDB | MAX3221EAE+TG1Z |
|---|---|---|---|---|---|---|
| Package | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Driver and Receiver Count | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| AutoShutdown | Yes | Yes | Yes | Yes | Yes | Yes |
| Automatic Wake-Up | Yes | Yes | Yes | Yes | Yes | Yes |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV | ±15 kV | ±15 kV | ±15 kV |
| External Charge-Pump Capacitors | 4 capacitors | 4 capacitors | 4 capacitors | 4 capacitors | 4 capacitors | 4 capacitors |
| Ordering-Code Grade | A-grade ordering code | A-grade ordering code | C-grade ordering code | C-grade ordering code | IDB ordering code | TG1Z ordering code |
Ключевые отличия
- Single-supply RS-232 operation (против MAX3221EAE+)
- Same-footprint grade flexibility (против MAX3221ECAE+T)
- Automatic low-power behavior (против MAX3221IDB)
- ESD resilience for exposed connectors (против MAX3221EAE+TG1Z)
Заметки по проектированию
Place the four external charge-pump capacitors close to their designated MAX3221 pins and use short, direct ground returns. Keep the charge-pump loop compact because long capacitor or ground connections can increase radiated noise and reduce the effectiveness of the automatic power-management behavior. Follow the manufacturer’s recommended PCB layout, including the relative placement of the RS-232 connector and logic-side circuitry.
Do not assume that all MAX3221 ordering codes are interchangeable without checking their temperature grade and qualification attributes. MAX3221EAE+T, MAX3221ECAE+T, MAX3221IDB, and MAX3221EAE+TG1Z share the functional family and 16-pin SSOP format, but the ordering suffix can change procurement or qualification requirements. Confirm the complete ordering table before a PCB or production substitution.
Route RS-232 driver outputs directly toward the connector and keep them away from sensitive analog inputs, crystal circuits, and switching-converter power paths. Maintain a compact signal-ground return with the line conductors. The MAX3221E family provides ±15 kV ESD protection, but connector placement, chassis grounding, and cable-entry practices remain important because the device rating does not remove every system-level transient risk.
Allow the device to enter its automatic shutdown state only when the connected system can tolerate the wake-up sequence. The MAX3221 family can reduce supply current to approximately 1 µA when no valid receiver activity is detected, but the host controller must use the enable and status pins correctly. Avoid repeatedly forcing the transmitter on when no peer is connected, because that removes the principal power-saving benefit of AutoShutdown.
Информация о соответствии
The MAX3221E family information identifies IEC 61000-4-2 ESD protection and ±15 kV ESD protection. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status are not explicitly established for the exact MAX3221EAE+T ordering code.