Analog Devices

MAX339CPE+ - Dual 4:1 CMOS Analog Multiplexer | Analog Devices

Артикул: MAX339CPE+ ✓ Активен
4.5 V to 30 V Vdss 400 ohms Rds(on) 16-pin PDIP Package
MOQ: 1 |

MAX339CPE+ Обзор

The Analog Devices MAX339CPE+ is a dual 4:1 CMOS analog multiplexer rated for 400 ohms maximum on-resistance, supplied in a 16-pin PDIP package. Each half of the device connects one of four inputs to a common output using two binary address inputs, and the multiplexers can operate as muxes or demultiplexers. The MAX339 supports a single supply from 4.5 V to 30 V or dual supplies from ±4.5 V to ±20 V.

A CMOS analog multiplexer is an interface IC that routes multiple analog signals through a shared internal path. The MAX339 belongs to the analog switch and multiplexer hierarchy, where its address logic selects one channel for connection while unselected channels are electrically isolated. Low-leakage CMOS construction makes the device useful when signals must be routed without significantly disturbing source impedance or bias currents.

The MAX339 provides two independent 4:1 sections, four input lines per section, and a common output for each section. Two address inputs select the active channel in each multiplexer. Its specified maximum on-resistance is 400 ohms according to the distributor listing, while a comparison of MAX339 package variants lists a maximum of 650 ohms under different operating conditions. The manufacturer identifies the MAX339 as a pin-compatible upgrade for the industry-standard DG508A and DG509A.

Operation is supported from a +4.5 V to +30 V single supply or from ±4.5 V to ±20 V dual supplies, allowing the common-output architecture to support both positive-only and bipolar signal systems. Because the device uses CMOS switches, channel behavior depends on the applied supply configuration, signal voltage, input impedance, and output load. Its low-leakage characteristic is particularly relevant when multiplexing high-impedance sensors, instrumentation signals, or precision measurement inputs.

Typical applications include data acquisition systems, test and measurement instruments, battery-powered monitoring equipment, industrial control interfaces, and signal-routing networks. It can also be used as a demultiplexer when a single source must be distributed selectively to several destinations. The 16-pin PDIP package supports through-hole assembly and prototyping rather than compact surface-mount production.

Designers should verify the address truth table, supply limits, input and output voltage limits, and switch on-state behavior before connecting external circuitry. Keep analog routing paths short, provide a stable supply reference, and account for the effect of on-resistance and leakage when calculating source impedance or measurement uncertainty.

This page combines the MAX339CPE+ technical characteristics with verified drop-in replacement analysis, package-aware comparisons, and practical guidance for analog routing and PCB implementation.

Аналоги без доработки для MAX339CPE+ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с MAX339CPE+ (тот же форм-фактор и посадочное место) — отличается по Package, Mounting Type, Multiplexer Configuration, Number of Channels, On-Resistance.

Analog Devices
Mounting Type: Through hole
Number of Channels: 8 analog input channels
On-Resistance: 400 ohm per DigiKey listing; 650 ohm per chipdig listing
Сравнить с MAX339CPE+ →
Maxim Integrated
Package: 16-QSOP
Mounting Type: Surface mount
Multiplexer Configuration: 8:1 single-ended
Сравнить с MAX339CPE+ →
Analog Devices
Package: 16-PDIP
Mounting Type: Through-hole
Number of Channels: 8 inputs to 1 common output
Сравнить с MAX339CPE+ →
Maxim Integrated
Mounting Type: Through hole
Multiplexer Configuration: 8-channel / dual 4-channel
Сравнить с MAX339CPE+ →

MAX339EPE+

✅ Прямая замена ⚠️ Характеристики не проверены
Maxim Integrated
📦 16-pin PDIP
8-channel / dual 4-channel · Dual 4:1 · CMOS · Low-leakage analog multiplexer · 16 · 16-pin PDIP · Rectangular · Through hole

Уточнить цену

Открыть даташит →

MAX339CPE+ Характеристики

Multiplexer Configuration Dual 4:1
Number of Circuits 2 circuits
Input Channels per Circuit 4 channels
Maximum On-Resistance 400 ohms
Single-Supply Voltage Range 4.5 V to 30 V
Dual-Supply Voltage Range +/-4.5 V to +/-20 V
Корпус 16-pin PDIP
Addressing 2-bit binary addressing per 4:1 section
Switch Type CMOS analog multiplexer
Operating Mode Mux or demux
Maximum On-Time 500 ns
Maximum Off-Time 500 ns
Minimum Operating Temperature 0 C

Руководство по цоколевке MAX339CPE+ в корпусе 16-pin pdip

Цоколевка для MAX339CPE+ (корпус 16-pin pdip). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.

Схема цоколевки корпуса 16-pin pdip для MAX339CPE+

Нет подробных данных о распиновке для MAX339CPE+.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

MAX339CPE+ подходит для 6 применениеs: Multichannel Data Acquisition, Battery-Powered Monitoring, Test and Measurement Signal Routing, Industrial Control Signal Multiplexing, Precision Sensor Interfacing, Programmable Signal Distribution.

📊

Multichannel Data Acquisition

The MAX339CPE+ suits data-acquisition front ends that must route several sensor channels to a shared analog-to-digital converter. Each 4:1 section uses two binary address inputs to select one of four inputs, allowing two acquisition groups to share one board area. The low-leakage CMOS architecture is advantageous for high-impedance sources, while the 400-ohm maximum on-resistance must be included in the source-impedance calculation. The 16-pin PDIP package also makes the device convenient for instrument prototypes and through-hole laboratory designs.

🔋

Battery-Powered Monitoring

The MAX339CPE+ can consolidate multiple monitored signals into a common path in a compact battery-powered instrument. Its dual 4:1 organization provides two independent routing groups, and the device accepts a single supply from 4.5 V to 30 V or bipolar supplies from +/-4.5 V to +/-20 V. Low-leakage behavior helps preserve accuracy when switching high-impedance sensor nodes. Because the package is a 16-pin PDIP, it is particularly suitable for prototypes, educational platforms, and moderately sized systems assembled with through-hole components.

🧪

Test and Measurement Signal Routing

The MAX339CPE+ is useful in test and measurement equipment that selects among multiple test points, sources, or return paths. Two address bits per section make channel selection straightforward for firmware-controlled systems, while the mux-or-demux capability supports both signal selection and distribution. The 4.5 V to 30 V operating range accommodates common laboratory rails, and the specified 400-ohm maximum on-resistance must be considered when driving high-impedance instruments. Designers should also account for leakage, settling behavior, and switch charge injection during precision measurements.

🏭

Industrial Control Signal Multiplexing

The MAX339CPE+ can route control, feedback, or diagnostic signals in an industrial control system while reducing the number of physical connections to a downstream controller. Its two independent 4:1 sections support grouped signal routing, and the wide single-supply range of 4.5 V to 30 V accommodates common industrial voltage rails. Low leakage is beneficial when the connected nodes have high source impedances. The design should verify common-mode limits at every switched node, provide a stable ground reference, and include the mux on-resistance in actuator or sensor feedback calculations.

📡

Precision Sensor Interfacing

The MAX339CPE+ fits precision sensor interfaces that present several high-impedance outputs to a shared measurement channel. Its low-leakage CMOS switches reduce unwanted interaction between unselected sensors, and the dual 4:1 arrangement lets two sensor groups be selected independently. The 400-ohm maximum on-resistance can create an input-impedance burden, so the source impedance and acquisition input must be evaluated together. Offset, leakage, settling time, and channel-switching transients should be included in the complete measurement uncertainty budget.

⚙️

Programmable Signal Distribution

The MAX339CPE+ can operate as a demultiplexer to distribute one programmable source toward several destination lines. This configuration is useful in automated test systems, selectable excitation networks, and sequential monitoring arrangements. Each internal section provides four destinations under two-bit address control, with two independent groups available in one device. The circuit must be designed around the manufacturer's mux/demux truth table and supply limits. Signal amplitude, load capacitance, leakage, and off-channel isolation should be checked before connecting sensitive or high-speed destinations.

Сводка рекомендуемых товаров

MAX338 Related single 8:1 member of the MAX338/MAX339 family Используется в: Multichannel Data Acquisition, Test and Measurement Signal Routing, Industrial Control Signal Multiplexing, Programmable Signal Distribution DG509A Industry-standard dual analog multiplexer cited as an upgrade reference Используется в: Multichannel Data Acquisition, Industrial Control Signal Multiplexing MAX328 Related Maxim low-leakage multiplexer family cited by the manufacturer Используется в: Battery-Powered Monitoring, Precision Sensor Interfacing MAX329 Related Maxim low-leakage multiplexer family cited by the manufacturer Используется в: Battery-Powered Monitoring, Precision Sensor Interfacing DG508A Industry-standard analog multiplexer cited as an upgrade reference Используется в: Test and Measurement Signal Routing, Programmable Signal Distribution
What is the MAX339CPE+ and what does it do?
The MAX339CPE+ is a dual 4:1 CMOS analog multiplexer with two independent sections, each able to connect one of four inputs to a common output. Two binary address inputs select the channel in each section, and the circuit can also operate as a demultiplexer. According to the Analog Devices MAX338/MAX339 datasheet, the device is intended for routing analog signals where low leakage and flexible single- or dual-supply operation are important.
What is the operating voltage range of MAX339CPE+?
The MAX339CPE+ operates from 4.5 V to 30 V with a single positive supply or from +/-4.5 V to +/-20 V with dual supplies. According to the Analog Devices MAX338/MAX339 datasheet, these operating ranges support positive-only systems as well as bipolar instrumentation. The selected supply configuration must also keep every applied input and output signal within the device's absolute maximum ratings.
Where can I download the MAX339CPE+ datasheet PDF?
The MAX339CPE+ datasheet PDF is available from Analog Devices at the manufacturer's MAX338/MAX339 data-sheet URL shown on this page. The document covers the shared MAX338 and MAX339 family, including the dual 4:1 MAX339 configuration, single- and dual-supply operation, address logic, electrical characteristics, and package information. Use the pin-description table in that document when assigning PCB connections.
Where can I find the MAX339CPE+ pinout?
The MAX339CPE+ pinout and pin descriptions are located in the pin-configuration section of the Analog Devices MAX338/MAX339 data sheet. The component is a 16-pin PDIP device with two address-control sections, paired common outputs, and associated enable inputs. Use the manufacturer pin table to verify signal names and logic levels rather than relying only on the functional mux or demux descriptions.
What are the key specifications engineers should know about MAX339CPE+?
The principal MAX339CPE+ specifications are a dual 4:1 configuration, 400-ohm maximum on-resistance, 4.5 V to 30 V single-supply operation, and +/-4.5 V to +/-20 V dual-supply operation. It is packaged in a 16-pin PDIP and can function as either a multiplexer or demultiplexer. According to the Analog Devices data sheet, the MAX339 is also identified as a pin-compatible upgrade for the DG508A and DG509A.
MAX339CPE+ vs MAX339EPE+ - which is better for industrial equipment?
The MAX339EPE+ is the better choice when the design requires the broader temperature grade associated with the E variant, while the MAX339CPE+ remains appropriate for a 0 C minimum operating temperature. Both use the same 16-pin PDIP architecture and retain the dual 4:1 CMOS multiplexer function. Confirm the complete temperature range, electrical limits, and lifecycle status in the manufacturer data sheet before fixing the BOM.
When should I choose MAX339CPE+ over another dual 4:1 multiplexer?
Choose the MAX339CPE+ when the design needs a 16-pin PDIP dual 4:1 switch with low-leakage CMOS behavior and operation from 4.5 V to 30 V or +/-4.5 V to +/-20 V. Its two independent address sections suit paired signal-routing or demultiplexing functions. Select a surface-mount alternative when board area is more important than through-hole assembly, and verify logic, leakage, and on-resistance requirements before substitution.
What can replace MAX339CPE+ on the same PCB?
The MAX339EPE+ is the closest same-package replacement identified within the MAX339 family because both use a 16-pin PDIP footprint and implement the dual 4:1 multiplexer function. Review temperature grade, supply range, leakage, on-resistance, logic levels, and enable behavior before replacing the MAX339CPE+. A manufacturer-approved cross-reference is required whenever a change involves an electrically different switching architecture.
Is MAX339CPE+ the same as MAX339EPE+?
No, the MAX339CPE+ and MAX339EPE+ are related variants rather than identical temperature-grade designations. Both are 16-pin PDIP dual 4:1 CMOS multiplexers, so their footprints and basic channel organization align. The principal selection point is operating grade and its associated environmental requirements. Confirm all electrical limits in the Analog Devices data sheet before treating one as a direct replacement for the other.
Is MAX339CPE+ suitable for high-impedance sensor multiplexing?
The MAX339CPE+ is suitable for high-impedance sensor multiplexing because it is designed as a low-leakage CMOS analog multiplexer. Its 4:1 sections can route selected sensor outputs to a common measurement channel, while a two-bit address selects the active input. The final error budget should include leakage, on-resistance, input capacitance, settling time, and the source impedance of the connected sensor.
How should MAX339CPE+ be used as a demultiplexer?
The MAX339CPE+ can be used as a demultiplexer by applying one source signal to a common input path and using the address inputs to direct that signal toward one of four destinations in the selected section. The two internal 4:1 sections provide two independent routing groups. Because the device contains both mux and demux-capable CMOS switches, control logic and signal-direction details should be verified against the manufacturer truth table.
Where can I buy MAX339CPE+ and check its current price?
Use the Request a Quote form on this page to request the current MAX339CPE+ price, stock position, minimum order quantity, and lead time. The manufacturer lists the MAX339 family as production, and the exact suffix and 16-pin PDIP package should be stated in the request. This prevents a quote request from being confused with the MAX338 or other package and temperature-grade variants.
What is the lead time for MAX339CPE+?
The current lead time for MAX339CPE+ should be requested through the Request a Quote form on this page using the complete suffix MAX339CPE+. Lead time can change with inventory, packaging, and order quantity, so confirm the manufacturer-listed availability at the time of quotation. Specify the required temperature grade, 16-pin PDIP package, and production quantity with the request.
Is MAX339CPE+ in stock for immediate shipment?
Current stock for MAX339CPE+ should be confirmed through the Request a Quote form on this page. The manufacturer lists the MAX339 family in production, but that family-level status does not guarantee a fixed quantity of the exact MAX339CPE+ suffix at every moment. Include your required quantity, date, and packaging preference so the quotation can reflect the exact orderable configuration.
How does MAX339CPE+ compare with DG508A and DG509A?
Analog Devices describes the improved MAX338 and MAX339 multiplexers as pin-compatible upgrades for the industry-standard DG508A and DG509A. The MAX339 specifically provides a dual 4:1 arrangement and supports 4.5 V to 30 V single-supply or +/-4.5 V to +/-20 V dual-supply operation. Because legacy DG devices can have different channel counts and electrical characteristics, compare the exact schematic position and signal direction before upgrading.
What is the best cross-brand equivalent for MAX339CPE+?
No cross-brand drop-in equivalent can be confirmed from the available manufacturer and distributor information for the MAX339CPE+. Its 16-pin PDIP dual 4:1 footprint, address logic, enable behavior, supply range, leakage, and signal-direction requirements must all match before a different manufacturer's part is considered a drop-in replacement. Submit the required electrical specifications through the Request a Quote form so the sourcing team can identify an appropriately qualified option.

Справочные инженерные данные для MAX339CPE+ — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the MAX339CPE+ for a through-hole design that requires two independent 4:1 CMOS analog routing sections, a 16-pin PDIP footprint, and operation from 4.5 V to 30 V or +/-4.5 V to +/-20 V. It is well suited to low-leakage signal selection, data-acquisition prototypes, and instrumentation assembled with through-hole components. The MAX339EPE+ is the closest same-footprint family alternative and should be considered when its broader operating-temperature grade is required; verify its complete limits before substitution. If PCB area is critical, a surface-mount multiplexer may be mechanically preferable, but it is not a drop-in replacement for the PDIP footprint. For any alternative, confirm channel direction, address logic, enable behavior, leakage, on-resistance, supply limits, and signal ratings before releasing the design.

Сравнение с аналогами

Параметр Этот товар MAX339EPE+
Package 16-pin PDIP 16-pin PDIP
Brand Analog Devices Analog Devices
Multiplexer Configuration Dual 4:1 Dual 4:1
Single-Supply Voltage Range 4.5 V to 30 V 4.5 V to 30 V
Dual-Supply Voltage Range +/-4.5 V to +/-20 V +/-4.5 V to +/-20 V
Maximum On-Time 500 ns 500 ns
Maximum Off-Time 500 ns 500 ns
Operating Modes Mux or demux Mux or demux

Ключевые отличия

  • Two independent 4:1 routing sections in one package (против MAX339EPE+)
  • Wide single-supply operating range (против MAX339EPE+)
  • Verified 400-ohm on-resistance listing (против MAX339EPE+)

Заметки по проектированию

Include the MAX339CPE+ on-resistance in the complete source-impedance calculation before selecting the device for a high-impedance sensor or precision converter input. The distributor listing specifies a maximum on-resistance of 400 ohms. This resistance combines with the sensor source resistance to alter gain, settling behavior, and converter input loading. Verify the acquisition stage's input impedance and settling time against the selected switching channel.

Follow the manufacturer pin-configuration table when assigning the 16-pin PDIP footprint and confirm the mux or demux signal direction for every section. Route switched analog nodes away from digital control and clock signals to reduce capacitive injection. Keep the ground reference continuous beneath and around the device, and place any required bypass capacitance close to the supply and ground pins.

Do not apply input or output voltages beyond the absolute maximum ratings in the MAX338/MAX339 data sheet. Signal excursions must remain compatible with the selected single or dual supply configuration, including transitions caused by external equipment. Also verify enable polarity and the two-bit address truth table before driving the control inputs; incorrect logic assumptions can connect the wrong source and disrupt an entire measurement sequence.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

Compliance declarations for the exact MAX339CPE+ orderable configuration were not identified. Confirm the applicable declarations with the manufacturer before production release.

Похожие запросы

MAX339CPE+ datasheet MAX339CPE+ pinout MAX339CPE+ datasheet pdf MAX339CPE+ equivalent MAX339CPE+ replacement MAX339CPE+ cross reference MAX339CPE+ vs MAX339EPE+ MAX339CPE+ 16-PDIP footprint MAX339CPE+ 4.5V to 30V MAX339CPE+ price MAX339CPE+ stock Analog Devices MAX339CPE+

Связанные компоненты & термины

Analog Devices MAX339CPE+ MAX339EPE+ MAX338 MAX328 MAX329 DG508A DG509A CMOS analog multiplexer analog switch multiplexer demultiplexer 4:1 multiplexer 16-pin PDIP DIP package through-hole package single-supply operation dual-supply operation on-resistance low leakage binary address control data acquisition test and measurement industrial control high-impedance sensor
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ