MAX339CPE+ - Dual 4:1 CMOS Analog Multiplexer | Analog Devices
MPN: MAX339CPE+ ✓ Hoạt độngMAX339CPE+ Tóm tắt
A CMOS analog multiplexer is an interface IC that routes multiple analog signals through a shared internal path. The MAX339 belongs to the analog switch and multiplexer hierarchy, where its address logic selects one channel for connection while unselected channels are electrically isolated. Low-leakage CMOS construction makes the device useful when signals must be routed without significantly disturbing source impedance or bias currents.
The MAX339 provides two independent 4:1 sections, four input lines per section, and a common output for each section. Two address inputs select the active channel in each multiplexer. Its specified maximum on-resistance is 400 ohms according to the distributor listing, while a comparison of MAX339 package variants lists a maximum of 650 ohms under different operating conditions. The manufacturer identifies the MAX339 as a pin-compatible upgrade for the industry-standard DG508A and DG509A.
Operation is supported from a +4.5 V to +30 V single supply or from ±4.5 V to ±20 V dual supplies, allowing the common-output architecture to support both positive-only and bipolar signal systems. Because the device uses CMOS switches, channel behavior depends on the applied supply configuration, signal voltage, input impedance, and output load. Its low-leakage characteristic is particularly relevant when multiplexing high-impedance sensors, instrumentation signals, or precision measurement inputs.
Typical applications include data acquisition systems, test and measurement instruments, battery-powered monitoring equipment, industrial control interfaces, and signal-routing networks. It can also be used as a demultiplexer when a single source must be distributed selectively to several destinations. The 16-pin PDIP package supports through-hole assembly and prototyping rather than compact surface-mount production.
Designers should verify the address truth table, supply limits, input and output voltage limits, and switch on-state behavior before connecting external circuitry. Keep analog routing paths short, provide a stable supply reference, and account for the effect of on-resistance and leakage when calculating source impedance or measurement uncertainty.
This page combines the MAX339CPE+ technical characteristics with verified drop-in replacement analysis, package-aware comparisons, and practical guidance for analog routing and PCB implementation.
Bộ thay thế dễ dàng lắp đặt cho MAX339CPE+ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX339CPE+ (cùng hình factor và footprint) — khác nhau ở Package, Mounting Type, Multiplexer Configuration, Number of Channels, On-Resistance.
MAX339EPE+
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX339CPE+ Thông số kỹ thuật
| Multiplexer Configuration | Dual 4:1 |
| Number of Circuits | 2 circuits |
| Input Channels per Circuit | 4 channels |
| Maximum On-Resistance | 400 ohms |
| Single-Supply Voltage Range | 4.5 V to 30 V |
| Dual-Supply Voltage Range | +/-4.5 V to +/-20 V |
| Hộp | 16-pin PDIP |
| Addressing | 2-bit binary addressing per 4:1 section |
| Switch Type | CMOS analog multiplexer |
| Operating Mode | Mux or demux |
| Maximum On-Time | 500 ns |
| Maximum Off-Time | 500 ns |
| Minimum Operating Temperature | 0 C |
Hướng dẫn cấu hình chân MAX339CPE+ 16-pin pdip
Cấu hình chân cho MAX339CPE+ (16-pin pdip gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX339CPE+.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX339CPE+ phù hợp cho 6 Áp dụngs: Multichannel Data Acquisition, Battery-Powered Monitoring, Test and Measurement Signal Routing, Industrial Control Signal Multiplexing, Precision Sensor Interfacing, Programmable Signal Distribution.
Multichannel Data Acquisition
The MAX339CPE+ suits data-acquisition front ends that must route several sensor channels to a shared analog-to-digital converter. Each 4:1 section uses two binary address inputs to select one of four inputs, allowing two acquisition groups to share one board area. The low-leakage CMOS architecture is advantageous for high-impedance sources, while the 400-ohm maximum on-resistance must be included in the source-impedance calculation. The 16-pin PDIP package also makes the device convenient for instrument prototypes and through-hole laboratory designs.
Được đề xuất
Battery-Powered Monitoring
The MAX339CPE+ can consolidate multiple monitored signals into a common path in a compact battery-powered instrument. Its dual 4:1 organization provides two independent routing groups, and the device accepts a single supply from 4.5 V to 30 V or bipolar supplies from +/-4.5 V to +/-20 V. Low-leakage behavior helps preserve accuracy when switching high-impedance sensor nodes. Because the package is a 16-pin PDIP, it is particularly suitable for prototypes, educational platforms, and moderately sized systems assembled with through-hole components.
Được đề xuất
Test and Measurement Signal Routing
The MAX339CPE+ is useful in test and measurement equipment that selects among multiple test points, sources, or return paths. Two address bits per section make channel selection straightforward for firmware-controlled systems, while the mux-or-demux capability supports both signal selection and distribution. The 4.5 V to 30 V operating range accommodates common laboratory rails, and the specified 400-ohm maximum on-resistance must be considered when driving high-impedance instruments. Designers should also account for leakage, settling behavior, and switch charge injection during precision measurements.
Được đề xuất
Industrial Control Signal Multiplexing
The MAX339CPE+ can route control, feedback, or diagnostic signals in an industrial control system while reducing the number of physical connections to a downstream controller. Its two independent 4:1 sections support grouped signal routing, and the wide single-supply range of 4.5 V to 30 V accommodates common industrial voltage rails. Low leakage is beneficial when the connected nodes have high source impedances. The design should verify common-mode limits at every switched node, provide a stable ground reference, and include the mux on-resistance in actuator or sensor feedback calculations.
Được đề xuất
Precision Sensor Interfacing
The MAX339CPE+ fits precision sensor interfaces that present several high-impedance outputs to a shared measurement channel. Its low-leakage CMOS switches reduce unwanted interaction between unselected sensors, and the dual 4:1 arrangement lets two sensor groups be selected independently. The 400-ohm maximum on-resistance can create an input-impedance burden, so the source impedance and acquisition input must be evaluated together. Offset, leakage, settling time, and channel-switching transients should be included in the complete measurement uncertainty budget.
Được đề xuất
Programmable Signal Distribution
The MAX339CPE+ can operate as a demultiplexer to distribute one programmable source toward several destination lines. This configuration is useful in automated test systems, selectable excitation networks, and sequential monitoring arrangements. Each internal section provides four destinations under two-bit address control, with two independent groups available in one device. The circuit must be designed around the manufacturer's mux/demux truth table and supply limits. Signal amplitude, load capacitance, leakage, and off-channel isolation should be checked before connecting sensitive or high-speed destinations.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX339CPE+ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX339EPE+ |
|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP |
| Brand | Analog Devices | Analog Devices |
| Multiplexer Configuration | Dual 4:1 | Dual 4:1 |
| Single-Supply Voltage Range | 4.5 V to 30 V | 4.5 V to 30 V |
| Dual-Supply Voltage Range | +/-4.5 V to +/-20 V | +/-4.5 V to +/-20 V |
| Maximum On-Time | 500 ns | 500 ns |
| Maximum Off-Time | 500 ns | 500 ns |
| Operating Modes | Mux or demux | Mux or demux |
Bảo phân biệt quan trọng
- Two independent 4:1 routing sections in one package (vsMAX339EPE+)
- Wide single-supply operating range (vsMAX339EPE+)
- Verified 400-ohm on-resistance listing (vsMAX339EPE+)
Ghi chú thiết kế
Include the MAX339CPE+ on-resistance in the complete source-impedance calculation before selecting the device for a high-impedance sensor or precision converter input. The distributor listing specifies a maximum on-resistance of 400 ohms. This resistance combines with the sensor source resistance to alter gain, settling behavior, and converter input loading. Verify the acquisition stage's input impedance and settling time against the selected switching channel.
Follow the manufacturer pin-configuration table when assigning the 16-pin PDIP footprint and confirm the mux or demux signal direction for every section. Route switched analog nodes away from digital control and clock signals to reduce capacitive injection. Keep the ground reference continuous beneath and around the device, and place any required bypass capacitance close to the supply and ground pins.
Do not apply input or output voltages beyond the absolute maximum ratings in the MAX338/MAX339 data sheet. Signal excursions must remain compatible with the selected single or dual supply configuration, including transitions caused by external equipment. Also verify enable polarity and the two-bit address truth table before driving the control inputs; incorrect logic assumptions can connect the wrong source and disrupt an entire measurement sequence.
Thông tin tuân thủ
Compliance declarations for the exact MAX339CPE+ orderable configuration were not identified. Confirm the applicable declarations with the manufacturer before production release.