MAX3485EESA+T - 12Mbps RS-485 Transceiver | Analog Devices
Артикул: MAX3485EESA+T ✓ АктивенMAX3485EESA+T Обзор
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus signals and converts received differential signals back into CMOS-compatible logic. These transceivers support noise-resistant communication over longer cables and multi-drop buses. The MAX3485E combines that differential interface function with low-power 3.3V operation and enhanced electrostatic-discharge protection for ports exposed to cables and industrial wiring.
Key features include true RS-485 and RS-422 operation, a 12Mbps data rate, slew-rate-limited signaling, and integrated ESD protection of ±15kV. The single-driver, single-receiver arrangement supports both point-to-point RS-422 links and half-duplex multidrop RS-485 networks. Its 8-pin SOIC package supports conventional surface-mount assembly and is also available in a tape-and-reel ordering configuration.
The differential driver reduces sensitivity to common-mode noise, while the receiver detects the polarity of the voltage difference across the A and B conductors rather than relying on an absolute signal level. Slew-rate limiting reduces high-frequency harmonics and helps control edge energy on the bus. The ±15kV protection rating adds an important margin for systems whose external connector or cable may be exposed to electrostatic discharge.
Typical uses include industrial automation, factory equipment, building controls, instrumentation, data acquisition, and embedded serial links. The MAX3485E is particularly suitable for a 3.3V controller that needs an RS-485 port without a higher-voltage supply or a separate external protection network. Firmware and termination practices remain important when designing a reliable multidrop network.
For a robust design, place the transceiver close to the connector, provide the required bus-termination and biasing components, connect the ground reference correctly, and route the differential pair as a tightly coupled pair. Keep protection and termination components close to the transceiver pins, and verify that the selected cables, connectors, grounding scheme, and baud rate meet the required communication distance.
This page combines manufacturer product information, interface characteristics, practical bus-layout guidance, and qualified drop-in alternatives. It also highlights the distinctions among related MAX3485-family devices so engineers can compare supply voltage, fail-safe behavior, package, and transceiver behavior before releasing a replacement to production.
Аналоги без доработки для MAX3485EESA+T — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MAX3485EESA+T (тот же форм-фактор и посадочное место) — отличается по Product Type, Maximum Data Rate, Package, RoHS Status, ESD Protection.
MAX3485ECSA+T
✅ Прямая заменаУточнить цену
Открыть даташит →MAX3486ECSA+T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX3440EASA+T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX3491EESD+T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
SP3485EN-L/TR
✅ Прямая заменаУточнить цену
Открыть даташит →MAX3485EESA+T Характеристики
| Product Type | 1/1 RS-422/RS-485 transceiver |
| Supply Voltage Range | 3V to 3.6V |
| Maximum Data Rate | 12Mbps |
| ESD Protection | ±15kV |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Supported Standards | RS-422 and RS-485 |
| Communication Mode | Half-duplex |
| Driver Output Type | Slew-rate-limited true RS-485/RS-422 |
| Корпус | 8-pin SOIC |
| Тип монтажа | Surface mount |
| RoHS Compliance | ROHS3 compliant |
| REACH Compliance | unknown |
| Lead-Free Status | unknown |
| Packaging Type | Tape and reel |
Руководство по цоколевке MAX3485EESA+T в корпусе 8-pin soic
Цоколевка для MAX3485EESA+T (корпус 8-pin soic). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для MAX3485EESA+T.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MAX3485EESA+T подходит для 6 применениеs: Industrial Automation Bus Interface, Factory Data-Acquisition System, Building Automation Controller, Embedded Serial Communication Port, Test and Measurement Instrument, RS-422 Point-to-Point Link.
Industrial Automation Bus Interface
The MAX3485EESA+T fits a 3.3V industrial controller that must communicate with remote sensors, actuators, PLC modules, or motor-control electronics over an RS-485 bus. Its 12Mbps maximum rate supports high-speed data transfer, while the differential interface improves immunity to the common-mode noise commonly encountered near motors and factory power systems. The ±15kV ESD protection also improves robustness where the bus connects to an external connector. Use the transceiver near the connector, route A and B as a differential pair, and apply termination and fail-safe biasing according to the bus topology.
Рекомендуется
Factory Data-Acquisition System
The MAX3485EESA+T can connect a data-acquisition controller to distributed measurement nodes that expose measurements through RS-485. The 12Mbps capability allows the link to carry frequent packets, while the 3V to 3.6V supply range simplifies integration with 3.3V sensors and embedded processors. Differential signaling reduces errors when cable runs pass near switching equipment. For reliable multidrop operation, confirm that only one driver is active at a time, install termination at physical bus ends, and select bias resistors for the idle state.
Рекомендуется
Building Automation Controller
The MAX3485EESA+T is appropriate for a 3.3V building-automation controller that links HVAC equipment, access-control panels, lighting controllers, or environmental monitors through RS-485. The integrated ±15kV ESD protection is valuable when the transceiver connects to building wiring through an external connector. Its 8-pin SOIC package simplifies compact controller-board assembly, and the 12Mbps capability provides ample bandwidth for command and telemetry traffic. Select the cable based on the required distance, maintain a common ground reference where permitted, and protect both signal conductors with an appropriate surge strategy.
Рекомендуется
Embedded Serial Communication Port
The MAX3485EESA+T adds a robust differential communications port to an embedded 3.3V controller without requiring a 5V interface. Its one-driver, one-receiver arrangement supports half-duplex point-to-point RS-422 links and multidrop RS-485 networks, making it useful for service consoles, remote I/O modules, and embedded test equipment. The 12Mbps rate supports high-speed protocols, while slew-rate limiting helps reduce unwanted high-frequency content. Ensure firmware manages driver enable, receiver timeout, and bus turnaround correctly to prevent contention.
Рекомендуется
Test and Measurement Instrument
The MAX3485EESA+T can provide the RS-485 or RS-422 link in a portable or rack-mounted measurement instrument. A 12Mbps differential interface supports rapid transfer of captured data from an instrument to a host, while the 3.3V operating range facilitates integration with modern low-power control logic. ESD protection helps reduce sensitivity to electrostatic discharge when users connect external test leads or communication cables. For dependable operation, isolate ground differences where necessary, control cable length and topology, and verify receiver performance over the full temperature range.
Рекомендуется
RS-422 Point-to-Point Link
The MAX3485EESA+T supports a full-duplex-style point-to-point RS-422 link when paired with the receive and transmit differential pairs defined for the application. Its slew-rate-limited true driver reduces signal distortion, and the 12Mbps capability accommodates high-speed control or data links between two circuit cards. Unlike a multidrop RS-485 bus, an RS-422 point-to-point connection generally has one driver on each differential pair. Confirm the receiver input range and logic thresholds, use twisted-pair wiring, and place termination only where it supports the intended signal path.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX3485EESA+T — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX3485ECSA+T | MAX3486ECSA+T | MAX3440EASA+T | MAX3491EESD+T | SP3485EN-L/TR |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Exar |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Product Type | 1/1 RS-422/RS-485 transceiver | 1/1 RS-422/RS-485 transceiver | 1/1 RS-422/RS-485 transceiver | RS-422/RS-485 transceiver | RS-422/RS-485 transceiver | RS-422/RS-485 transceiver |
| Supply Voltage | 3V to 3.6V | 3V to 3.6V | 3V to 3.6V | 3V to 3.6V | 3V to 3.6V | 3.3V class |
| Driver and Receiver Count | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver |
Ключевые отличия
- Direct MAX3485E family match (против MAX3485ECSA+T)
- True fail-safe receiver option (против MAX3486ECSA+T)
- Established 12Mbps RS-485/RS-422 positioning (против SP3485EN-L/TR)
Заметки по проектированию
Place the MAX3485EESA+T close to the RS-485 or RS-422 connector and termination network. Route A and B as a tightly coupled differential pair over a continuous ground plane, minimize stubs, and avoid sharing the pair with unrelated high-current or switching paths. Keep the interface return ground available and ensure its reference relationship is appropriate for the installation. Compact placement shortens the unprotected portion of the cable connection and improves ESD-current diversion into the board's grounding structure.
Do not assume that an SOIC-8 package alone proves replacement compatibility. Compare the exact pin function, driver-enable polarity, receiver thresholds, fail-safe response, supply limits, and shutdown behavior for every candidate. On a multidrop bus, ensure only one driver is enabled at a time and provide bias resistors that hold the bus in a defined idle state. Fit termination only at the physical ends of the trunk, not at every node, and remove unnecessary branch stubs.
Slew-rate limiting reduces edge energy, but reliable operation still requires an appropriate cable, topology, and baud-rate margin. Use twisted-pair wiring, avoid long unterminated branches, and test the complete network with its planned node count and cable length. If the cable leaves the enclosure, combine the transceiver's ±15kV ESD capability with appropriately coordinated surge and overvoltage protection. Validate the external protection network so that its capacitance and clamping behavior do not distort the intended data rate.
Информация о соответствии
The component is identified as ROHS3 compliant. REACH, lead-free, halogen-free, and conflict-minerals status were not established from authoritative compliance information. AEC-Q100 qualification is not applicable to this catalog classification.