Analog Devices

MAX358CWE+ - Fault-Protected 8:1 Analog Multiplexer | ADI

Артикул: MAX358CWE+ ✓ Активен
4.5 V to 18 V Vdss 1.8 kOhm Rds(on) 16-pin SOIC Package
MOQ: 1 |

MAX358CWE+ Обзор

Analog Devices MAX358CWE+ is a fault-protected, 8-channel single-ended analog multiplexer with an 8:1 configuration, 1.8 kOhm on-resistance and approximately 1 MHz bandwidth in a 16-pin SOIC package. According to the manufacturer product page, the MAX358 family is designed for multiplexers and demultiplexers that must withstand fault conditions beyond their normal supply rails.

An analog multiplexer is an interface IC that routes one of several input channels to a shared output or measurement path. The MAX358 belongs to the broader hierarchy of analog switches, multiplexers, interface ICs and semiconductors. By selecting among eight single-ended inputs with controlled switches, it reduces the number of signal lines required between sensors, test points, data-conversion systems and other analog circuits.

The MAX358 family combines an 8:1 configuration with 1.8 kOhm on-resistance and approximately 1 MHz bandwidth. Its listed operating supply range is 4.5 V to 18 V, while the fault-protection architecture provides protection for overvoltage conditions extending to ±35 V beyond the supply rails when power is removed. The manufacturer describes the implementation as a series N-channel, P-channel, N-channel structure.

MAX358 is the single-ended member of a related fault-protected multiplexer family. The MAX359 provides a four-channel differential configuration, while the MAX358 is intended for eight-channel single-ended routing. The device uses address and control inputs to select the active path and supports analog signal multiplexing in systems where input faults, limited board area and modest bandwidth are more important than very low on-resistance.

Typical uses include data acquisition, instrumentation, test and measurement, industrial control, battery monitoring and embedded analog signal routing. The 1 MHz bandwidth is suitable for many sensor and control signals, while the fault-protection feature helps isolate downstream circuitry from excessive input voltage. System designers should still validate signal levels, transition behavior and protection conditions against the manufacturer datasheet.

PCB implementation requires careful routing of the selected analog path and control signals to prevent interference between channels. Place the multiplexer close to the source or destination of the routed signal, maintain a continuous ground reference, and follow the datasheet layout guidance for bypass capacitors and exposed routing areas.

This product page combines the manufacturer specifications with practical design guidance, package information, sourcing workflow and verified drop-in alternatives. It is intended to help engineers determine whether the MAX358CWE+ fits an analog routing design before detailed circuit simulation and board validation.

Аналоги без доработки для MAX358CWE+ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Для этого товара нет аналогов без доработки.

Запросить аналоги

MAX358CWE+ Характеристики

Multiplexer Configuration 8:1
Number of Channels 8 channels
Signal Type Single-ended analog
On-Resistance 1.8 kOhm
Bandwidth 1 MHz
Crosstalk 42 dB
Supply Voltage Range 4.5 V to 18 V
Fault-Protection Range Up to ±35 V beyond supply rails
Internal Switch Structure Series N-channel, P-channel, N-channel
Количество выводов 16 pins
Корпус 16-pin SOIC
Тип монтажа Surface mount
Operating Temperature Grade Commercial extended temperature grade

Руководство по цоколевке MAX358CWE+ в корпусе 16-pin soic

Цоколевка для MAX358CWE+ (корпус 16-pin soic). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.

Схема цоколевки корпуса 16-pin soic для MAX358CWE+

Нет подробных данных о распиновке для MAX358CWE+.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

MAX358CWE+ подходит для 6 применениеs: Multichannel Data Acquisition, Automated Test Equipment, Industrial Sensor Multiplexing, Battery Cell Monitoring, Instrumentation Signal Routing, Embedded Control Interfaces.

📡

Multichannel Data Acquisition

The MAX358CWE+ fits data-acquisition systems that must route eight single-ended sensor signals through a shared amplifier, ADC or measurement instrument. Its 8:1 configuration reduces the number of analog connections reaching the converter, while approximately 1 MHz bandwidth covers many pressure, temperature, position and industrial process signals. The 1.8 kOhm on-resistance must be included when calculating source loading and attenuation. For high-impedance sensors, verify settling behavior and add suitable buffering when the selected ADC input requires a lower source impedance. The fault-protected architecture is particularly valuable where an external wiring fault could otherwise place excessive voltage on the multiplexed input.

🔧

Automated Test Equipment

The MAX358CWE+ can select among eight test points or instrument channels in automated test equipment, reducing the number of analog paths required between the DUT interface and measurement circuitry. The approximately 1 MHz bandwidth is suitable for many low- and moderate-frequency production tests, including continuity, resistance, sensor response and signal-conditioning checks. Because the multiplexer contributes 1.8 kOhm of on-resistance, test engineers should account for path resistance and add external compensation when measuring high-impedance nodes. The fault-protected input structure helps prevent an out-of-range DUT signal from propagating excessive fault voltage through the routing network.

🏭

Industrial Sensor Multiplexing

The MAX358CWE+ is suitable for industrial control boards that collect multiple single-ended sensors and route them to a shared controller or analog front end. It accommodates eight channels in a compact 16-pin SOIC and operates from a 4.5 V to 18 V supply, covering common industrial signal-chain voltages. The fault-protection architecture is valuable when sensors and field wiring can experience transients or wiring faults. Designers should still provide normal input clamping, protection and filtering as appropriate for the installation. The 1.8 kOhm on-resistance is important when sensors have high output impedance because the selected path will load the source and can create measurement error.

🔋

Battery Cell Monitoring

The MAX358CWE+ can multiplex multiple single-ended battery or power-monitoring taps into a shared measurement channel. Its 8:1 configuration helps limit the number of analog inputs required by the monitoring circuitry, while the 4.5 V to 18 V operating range is compatible with appropriately designed measurement systems. Fault protection is particularly relevant when monitored nodes are exposed to unexpected voltage transients. The circuit designer must confirm that every monitored node remains within the absolute maximum ratings, including during abnormal conditions. The 1.8 kOhm path resistance should be included in the acquisition front end, particularly for high-impedance dividers and precision measurements.

📊

Instrumentation Signal Routing

The MAX358CWE+ fits instrumentation designs that need to route several low-frequency analog sources into a shared precision measurement path. Eight single-ended channels can be selected by address and enable logic, reducing wiring complexity around the measurement frontend. Its approximately 1 MHz bandwidth supports many sensor and control-bandwidth signals, although the 1.8 kOhm on-resistance may require compensation in high-impedance systems. The fault-protected structure improves robustness when external inputs can experience wiring errors. Instrument designers should also evaluate leakage, channel switching transients and settling behavior using the manufacturer test conditions.

⚙️

Embedded Control Interfaces

The MAX358CWE+ can expand the analog input capacity of an embedded controller by selecting one of eight single-ended signals for conversion or supervision. The compact SOIC-16 package preserves board area, and the 1.8 kOhm on-resistance is compatible with many moderately low-impedance sensor networks. Address-control logic allows the firmware to scan channels sequentially, while the fault-protection architecture adds resilience to connector or wiring faults. Engineers should select external input protection for the exact surge environment, confirm channel-to-channel isolation in the target bandwidth and verify that the selected analog front end settles within the required sampling interval.

Сводка рекомендуемых товаров

MAX358CWE+ Analog Devices Используется в: Multichannel Data Acquisition, Automated Test Equipment, Industrial Sensor Multiplexing, Battery Cell Monitoring, Instrumentation Signal Routing, Embedded Control Interfaces MAX358CPE+ DIP-package family member with the same core multiplexer function Используется в: Multichannel Data Acquisition, Instrumentation Signal Routing MAX359 Differential fault-protected family alternative for balanced test paths Используется в: Automated Test Equipment, Industrial Sensor Multiplexing, Battery Cell Monitoring, Embedded Control Interfaces
What is the MAX358CWE+?
The MAX358CWE+ is a fault-protected, 8-channel single-ended analog multiplexer in a 16-pin SOIC package. According to the Analog Devices MAX358 product page, it uses an 8:1 configuration with 1.8 kOhm on-resistance and approximately 1 MHz bandwidth. The device belongs to the MAX358 fault-protected multiplexer family and is intended to route one selected analog channel through a common signal path while limiting fault-induced damage.
What are the key specifications of MAX358CWE+ that engineers should know?
The MAX358CWE+ combines an 8:1 single-ended configuration, 1.8 kOhm on-resistance, approximately 1 MHz bandwidth and a 4.5 V to 18 V supply range. According to the Analog Devices MAX358 product page, its fault-protection structure can withstand overvoltage up to ±35 V beyond the supply rails under the specified power-removed condition. It is packaged in a 16-pin SOIC for surface-mount assembly.
Where can I download the MAX358CWE+ datasheet PDF?
The MAX358CWE+ datasheet should be obtained from the official Analog Devices MAX358 product page at https://www.analog.com/en/products/max358.html. That page provides the manufacturer documentation and product-selection information. Use the manufacturer datasheet to confirm the complete pin description, electrical characteristics, control truth table, absolute maximum ratings and recommended application circuit before releasing a PCB design.
Where can I find the MAX358CWE+ pinout?
Use the pin configuration and package drawing in the manufacturer MAX358 datasheet for the authoritative MAX358CWE+ pinout. The component is supplied in a 16-pin SOIC package, but individual pin names and signal assignments are not shown on the product-page summary. The manufacturer datasheet should be consulted before connecting address, enable, supply and analog-channel pins to avoid errors in routing or control logic.
What supply voltage does the MAX358CWE+ require?
The MAX358CWE+ operates from 4.5 V to 18 V according to the Analog Devices MAX358 product information. The fault-protection capability is distinct from the normal operating supply range: the manufacturer describes protection for voltages extending to ±35 V beyond the supply rails when power is removed. Circuit designers must distinguish normal operation limits from the stated fault-conditions and consult the datasheet absolute maximum ratings.
What is the bandwidth and on-resistance of MAX358CWE+?
The MAX358CWE+ provides approximately 1 MHz bandwidth and 1.8 kOhm on-resistance. The Analog Devices MAX358 product page identifies these values for the 8-channel, single-ended fault-protected multiplexer. This combination is appropriate for many sensor, instrumentation and analog-control signals, although applications requiring substantially lower insertion resistance or higher bandwidth should not assume the MAX358 is the appropriate choice.
MAX358CWE+ vs MAX358CPE+ - which package should I choose?
The MAX358CWE+ is the surface-mount SOIC-16 option, while the MAX358CPE+ is the through-hole DIP-16 option. Both are described as 8-channel single-ended fault-protected multiplexers, but they use different PCB footprints and are therefore not direct package-compatible replacements. Existing SOIC layouts should use the MAX358CWE+, whereas new through-hole or legacy DIP layouts may be designed around the MAX358CPE+.
What is the difference between MAX358CWE+ and MAX359?
The MAX358CWE+ is an eight-channel single-ended 8:1 multiplexer, while the MAX359 is a four-channel differential multiplexer with a 2-of-8 configuration. According to the Analog Devices product description, both are part of Maxim's fault-protected multiplexer families and use an N-channel, P-channel, N-channel switch structure. Choose based on whether the signal source is single-ended or differential.
When should I choose MAX358CWE+ over a conventional analog multiplexer?
Choose the MAX358CWE+ when eight single-ended analog signals must share one path and the application may expose the mux inputs to excessive voltage. Its 8:1 organization, 1.8 kOhm on-resistance and fault-protection architecture provide a practical combination for instrumentation and test systems. A conventional multiplexer may be preferable when fault protection is unnecessary, lower on-resistance is required or a different channel count is needed.
Is MAX358CWE+ suitable for a 1 MHz analog signal?
The MAX358CWE+ is rated for approximately 1 MHz bandwidth, making it relevant to analog signals within that bandwidth range. The 1.8 kOhm on-resistance can still create signal attenuation and loading effects in high-impedance or high-frequency networks. Confirm the source impedance, destination impedance, capacitance, attenuation and allowable distortion in the target circuit before finalizing the design.
What is the best drop-in replacement for MAX358CWE+?
The verified MAX358CWE+ cross-reference results do not identify five distinct pin-compatible replacements in the same SOIC-16 footprint. MAX358CPE+ performs the same basic multiplexer function but uses a through-hole DIP-16 package and is not a PCB drop-in substitute for MAX358CWE+. Use the manufacturer product-selection table to identify an exact SOIC-16 ordering code and confirm pin compatibility before approving any substitution.
Can MAX358CPE+ replace MAX358CWE+ on the same PCB?
No, the MAX358CPE+ cannot directly replace the MAX358CWE+ on the same PCB because the former uses a through-hole DIP-16 footprint and the latter uses a surface-mount SOIC-16 footprint. Although both belong to the MAX358 family and provide an 8-channel single-ended fault-protected multiplexer function, their physical pin spacing and mounting requirements differ. A board redesign or adapter would be necessary.
Where can I buy MAX358CWE+ online?
Use the Request a Quote form on this page to request MAX358CWE+ availability, commercial terms and an order quote. The manufacturer product page at https://www.analog.com/en/products/max358.html is the authoritative source for the device and its documentation. Current stock, minimum order quantity and delivery schedule should be confirmed through the quote workflow.
What is the price of MAX358CWE+?
Use the Request a Quote form on this page for the current MAX358CWE+ price and quantity terms. Commercial pricing can vary with order quantity, production status and supply conditions, so confirm the required quantity and target date when requesting a quote. The manufacturer product page provides the product overview and ordering information for this MAX358 family member.
What is the lead time and stock status for MAX358CWE+?
Request the current MAX358CWE+ stock status, lead time and minimum order quantity through the Request a Quote form on this page. The Analog Devices MAX358 product page identifies the MAX358 as a production family and provides the product-selection table, but current fulfillment conditions should be confirmed for the exact SOIC-16 ordering code and required quantity.

Справочные инженерные данные для MAX358CWE+ — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the MAX358CWE+ when the design requires eight single-ended analog inputs, an SOIC-16 surface-mount footprint and protection against specified overvoltage faults. Its 8:1 configuration, 1.8 kOhm on-resistance and approximately 1 MHz bandwidth are appropriate for many data-acquisition, industrial-monitoring, test and instrumentation signals. The MAX358CPE+ offers the same core family function but requires a through-hole DIP layout, so it is not a drop-in choice for an existing SOIC board. The MAX359 is preferable when the source signals are differential and require a four-channel 2-of-8 arrangement. If the application requires substantially lower on-resistance, much higher bandwidth or more than eight channels, select a different multiplexer architecture and recalculate acquisition time, attenuation, channel isolation and protection requirements.

Сравнение с аналогами

Параметр Этот товар
Package 16-pin SOIC
Brand Analog Devices
Multiplexer Configuration 8:1
Number of Channels 8 single-ended channels
On-Resistance 1.8 kOhm
Bandwidth 1 MHz
Supply Voltage Range 4.5 V to 18 V
Crosstalk 42 dB
Fault Protection Up to ±35 V beyond supply rails under the specified power-removed condition

Ключевые отличия

  • Combines eight-way routing with fault protection (против Conventional unprotected analog multiplexer)
  • Single-ended routing in a compact surface-mount package (против MAX358CPE+)
  • Useful bandwidth for low- and moderate-frequency instrumentation (против MAX359)

Заметки по проектированию

Place the MAX358CWE+ close to the multiplexed signal source or destination to minimize trace resistance, capacitance and susceptibility to interference. Route the selected analog channel as a continuous, compact path, keep digital address and enable traces away from sensitive inputs, and use a solid ground reference. Follow the manufacturer datasheet for bypass-capacitor placement and recommended layout geometry.

Do not treat the stated ±35 V fault-protection capability as permission to exceed the absolute maximum ratings during normal operation. Confirm the exact supply-off condition, input current, duration and pin limits in the manufacturer datasheet. The 1.8 kOhm on-resistance can also create attenuation and settling errors in high-impedance networks, so include it in the signal-path calculation.

Analyze the complete switched path rather than relying only on the 1 MHz bandwidth figure. Include source impedance, 1.8 kOhm on-resistance, load capacitance, control-line timing and downstream acquisition time. For precision or high-impedance measurements, add a low-capacitance buffer after the multiplexer and verify crosstalk and channel-to-channel switching transients on the finished layout.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The MAX358CWE+ is identified as a production MAX358 family member. RoHS, REACH, AEC-Q100, lead-free, halogen-free and conflict-minerals status require confirmation from the manufacturer product documentation or current compliance declarations.

Данные проверены: 2026-11-14 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

MAX358CWE+ datasheet MAX358CWE+ datasheet pdf MAX358CWE+ pinout MAX358CWE+ specifications Analog Devices MAX358CWE+ MAX358CWE+ SOIC-16 MAX358CWE+ 8:1 multiplexer MAX358CWE+ 1 MHz bandwidth MAX358CWE+ equivalent MAX358CWE+ replacement MAX358CWE+ cross reference MAX358CWE+ vs MAX358CPE+ MAX358CWE+ price MAX358CWE+ stock

Связанные компоненты & термины

Analog Devices Maxim Integrated MAX358CWE+ MAX358 MAX358CPE+ MAX359 HL-508A HL-509A analog multiplexer analog switch multiplexer and demultiplexer interface IC semiconductor 8:1 multiplexer single-ended analog signal differential analog signal fault protection on-resistance 1.8 kOhm 1 MHz bandwidth 42 dB crosstalk 4.5 V to 18 V supply SOIC-16 QFN family surface mount SMD data acquisition test and measurement industrial sensor multiplexing battery monitoring
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ