MC33662LEF - 20 kbit/s LIN Transceiver | NXP | SOIC-8
Артикул: MC33662LEF ✓ АктивенMC33662LEF Обзор
A LIN transceiver is the physical-layer interface between digital controller logic and a low-cost, single-wire automotive network. Within the communication hierarchy, the MC33662LEF is a LIN physical-layer transceiver, an automotive bus transceiver, an interface IC, and a semiconductor. It translates host-side TXD and RXD signals into the dominant and recessive states used on the LIN bus, while providing bus-level protection and fault-tolerant behavior for vehicle electrical environments.
Key characteristics include a nominal 20 kbit/s LIN data rate, LIN 2.x compatibility, SAE J2602-2 support, a 7 V to 18 V supply range, and compatibility with both 3.3 V and 5.0 V logic inputs. The NXP MC33662 family also supports a 100 kbit/s test and programming baud rate. These features make the MC33662LEF appropriate for body electronics, door modules, lighting controllers, climate-control nodes, seat controls, and other distributed automotive systems.
The L suffix identifies the 20 kbit/s LIN operating-rate variant. NXP also documents a fast 100 kbit/s mode for test or programming activities, but that mode is not the normal LIN communication rate. The EF package suffix denotes the 8-pin SOIC configuration, which simplifies assembly where a conventional surface-mount automotive transceiver package is required.
In a typical LIN network, the vehicle controller supplies serial data to TXD and reads the interpreted bus state from RXD. The transceiver drives the LIN line through its LIN output and includes an internal pull-up arrangement, while an external pull-up and bus termination network are normally required on the complete LIN wiring. The host must also handle frame headers, checksums, scheduling, diagnostics, and fault management above the physical layer.
PCB implementation requires close attention to the LIN connection, supply decoupling, ground return, and protection network. Place the transceiver near the LIN connector, route the LIN trace away from sensitive analog and high-speed digital signals, provide a low-impedance ground path, and use the application guidance in the manufacturer datasheet for external protection and pull-up components. The 8-pin SOIC footprint is easy to route, but vehicle transceivers still require careful EMC-oriented layout.
This page consolidates the manufacturer product-page facts, distributor package information, interface requirements, design guidance, and qualification-aware replacement considerations into an engineering-focused reference for MC33662LEF selection and implementation.
Аналоги без доработки для MC33662LEF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MC33662LEF (тот же форм-фактор и посадочное место) — отличается по Package, Product Type.
MC33662SEF
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MC33662JEF
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MC33662LEF Характеристики
| Product Type | LIN physical-layer transceiver |
| Nominal LIN Data Rate | 20 kbit/s |
| Fast Test and Programming Baud Rate | 100 kbit/s |
| LIN Specification Compatibility | LIN 2.x |
| Automotive Network Standard | SAE J2602-2 |
| Supply Voltage Range | 7 V to 18 V |
| Controller Input Compatibility | 3.3 V and 5.0 V |
| Transceiver Configuration | 1/1 half-duplex LIN transceiver |
| Корпус | 8-pin SOIC |
| Package Family | SOIC-8 surface-mount package |
| Тип монтажа | Surface mount |
| Application Domain | Automotive LIN sub-bus |
| Bus Type | Single-wire Local Interconnect Network |
| Статус RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Конфигурация выводов MC33662LEF
| Контакт 1 | RXD — Receive data output from the LIN bus |
| Контакт 2 | GND — Ground connection |
| Контакт 3 | TXD — Transmit data input from the host controller |
| Контакт 4 | NC — Not connected |
| Контакт 5 | VCC — Logic supply connection |
| Контакт 6 | VSUP — Vehicle supply connection |
| Контакт 7 | GND — Ground connection |
| Контакт 8 | LIN — LIN bus transceiver connection |
Типичное применение
MC33662LEF подходит для 6 применениеs: Automotive Door Control Module, Automotive Lighting Controller, Climate Control Node, Seat and Switch Module, Automotive Sensor Gateway, Vehicle Test and Programming Interface.
Automotive Door Control Module
The MC33662LEF fits door-control nodes that exchange switch, motor-command, and sensor information over a 20 kbit/s LIN sub-bus. Its 7 V to 18 V operating range accommodates vehicle power environments, while 3.3 V and 5.0 V controller compatibility allows the same physical layer to serve different host MCU logic levels. Place the transceiver close to the connector, provide a low-impedance ground return, and use the manufacturer application circuit for the LIN pull-up and protection network. Its SAE J2602-2 and LIN 2.x support makes it appropriate for qualified body-network designs, subject to the exact device grade and vehicle specification.
Рекомендуется
Automotive Lighting Controller
The MC33662LEF can connect a lighting controller to a LIN remote node that carries switching commands and diagnostic information. The 20 kbit/s L-series rate matches standard LIN communication, and the 7 V to 18 V supply range supports vehicle-level operation. The controller interface accepts 3.3 V or 5.0 V signals, simplifying integration with different MCU families. Keep the LIN trace short near the wiring connector, route it away from LED-driver switching nodes, and use a solid ground return to reduce susceptibility to conducted disturbances in the vehicle harness.
Рекомендуется
Climate Control Node
The MC33662LEF is appropriate for climate-control subsystems that distribute motor and sensor commands over a low-cost LIN network. Its LIN 2.x and SAE J2602-2 support aligns the physical layer with modern automotive sub-bus requirements, while the 20 kbit/s rate provides sufficient throughput for bounded control and diagnostic messages. The transceiver isolates the host controller from the physical LIN wiring, but software must still implement frame timing, checksum handling, and fault recovery. Position the device near the harness interface and protect the LIN route according to the NXP reference application.
Рекомендуется
Seat and Switch Module
The MC33662LEF suits compact seat, switch, and convenience modules where numerous distributed nodes need inexpensive communication. Its 20 kbit/s rate and single-wire LIN interface support deterministic command exchange without a full CAN network. The 7 V to 18 V supply operation aligns with vehicle electrical systems, while the selectable controller-side logic compatibility supports both 3.3 V and 5.0 V hosts. For low-current modules, verify sleep-current requirements and the complete external bus network in the manufacturer datasheet. Use short supply decoupling and route the LIN conductor away from switches and inductive loads.
Рекомендуется
Automotive Sensor Gateway
The MC33662LEF can serve as the LIN-facing element of a gateway that collects inputs from distributed automotive sensors and forwards status to a higher-level controller. LIN 2.x and SAE J2602-2 compatibility support use in modern vehicle sub-networks, and the 20 kbit/s L-series rate matches normal control traffic. The device accepts both 3.3 V and 5.0 V controller inputs, but logic thresholds and timing still require verification against the host MCU. Keep the transceiver close to the connector, provide an uninterrupted ground path, and implement software diagnostics for missing frames, bus shorts, and invalid headers.
Рекомендуется
Vehicle Test and Programming Interface
The MC33662 family includes a 100 kbit/s mode for test and programming activities, making the MC33662LEF relevant to production and diagnostic interfaces that need more than the normal 20 kbit/s LIN traffic rate. Designers should distinguish this fast mode from ordinary LIN communication and verify the applicable baud-rate selection, timing, and host configuration in the manufacturer datasheet. The 8-pin SOIC package supports conventional surface mounting, while the 7 V to 18 V supply and 3.3 V or 5.0 V controller compatibility align with embedded test equipment and vehicle electronic modules.
Рекомендуется
Справочные инженерные данные для MC33662LEF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MC33662SEF | MC33662JEF |
|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Product Type | LIN physical-layer transceiver | LIN physical-layer transceiver | LIN physical-layer transceiver |
| LIN Compatibility | LIN 2.x | LIN 2.x | LIN 2.x |
| Automotive Network Standard | SAE J2602-2 | SAE J2602-2 | SAE J2602-2 |
| Supply Voltage Range | 7 V to 18 V | 7 V to 18 V | 7 V to 18 V |
| Controller Input Compatibility | 3.3 V and 5.0 V | 3.3 V and 5.0 V | 3.3 V and 5.0 V |
| Fast Test and Programming Rate | 100 kbit/s | 100 kbit/s | 100 kbit/s |
| RoHS Status | unknown | unknown | unknown |
Ключевые отличия
- Standard 20 kbit/s LIN operating-rate selection (против MC33662SEF)
- Automotive physical-layer compatibility (против MC33662JEF)
- Controller integration flexibility (против MC33662SEF)
Заметки по проектированию
Place the MC33662LEF near the LIN connector and keep the LIN trace short and isolated from sensitive analog or high-speed digital paths. Route the vehicle ground return directly to the transceiver ground with a low-impedance path. Apply the manufacturer reference circuit for the external pull-up and protection components, and avoid long stubs that could increase bus-edge distortion.
Decouple the logic and vehicle-supply pins directly at the package according to the NXP application diagram. Keep high-current switching regulators and inductive components away from the transceiver supply pins, and verify the supply ramp, operating range, and any sleep-mode requirements in the manufacturer datasheet. The 7 V to 18 V input capability does not eliminate transient protection requirements for an automotive harness.
Do not select a family variant solely because it uses an 8-pin SOIC. MC33662LEF is the 20 kbit/s L-series selection, so nominal baud rate and pin configuration must match the LIN master and host design. Also verify logic thresholds, dominant-state behavior, diagnostic support, qualification grade, and temperature range before approving a replacement.
Информация о соответствии
The available product information confirms automotive LIN use and SAE J2602-2 compatibility but does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.