NXP Semiconductors

MC33662LEF - 20 kbit/s LIN Transceiver | NXP | SOIC-8

MPN: MC33662LEF ✓ Aktif
7 V to 18 V Vdss 8-pin SOIC Package
MOQ: 1 |

MC33662LEF Genel Bakış

The NXP Semiconductors MC33662LEF is a 20 kbit/s LIN physical-layer transceiver for automotive networks, supplied in an 8-pin SOIC package. It supports LIN 2.x and SAE J2602-2, accepts 3.3 V or 5.0 V controller signals, and operates from a 7 V to 18 V vehicle supply. The device connects a host microcontroller or LIN-capable cluster ECU to the wired LIN sub-bus.

A LIN transceiver is the physical-layer interface between digital controller logic and a low-cost, single-wire automotive network. Within the communication hierarchy, the MC33662LEF is a LIN physical-layer transceiver, an automotive bus transceiver, an interface IC, and a semiconductor. It translates host-side TXD and RXD signals into the dominant and recessive states used on the LIN bus, while providing bus-level protection and fault-tolerant behavior for vehicle electrical environments.

Key characteristics include a nominal 20 kbit/s LIN data rate, LIN 2.x compatibility, SAE J2602-2 support, a 7 V to 18 V supply range, and compatibility with both 3.3 V and 5.0 V logic inputs. The NXP MC33662 family also supports a 100 kbit/s test and programming baud rate. These features make the MC33662LEF appropriate for body electronics, door modules, lighting controllers, climate-control nodes, seat controls, and other distributed automotive systems.

The L suffix identifies the 20 kbit/s LIN operating-rate variant. NXP also documents a fast 100 kbit/s mode for test or programming activities, but that mode is not the normal LIN communication rate. The EF package suffix denotes the 8-pin SOIC configuration, which simplifies assembly where a conventional surface-mount automotive transceiver package is required.

In a typical LIN network, the vehicle controller supplies serial data to TXD and reads the interpreted bus state from RXD. The transceiver drives the LIN line through its LIN output and includes an internal pull-up arrangement, while an external pull-up and bus termination network are normally required on the complete LIN wiring. The host must also handle frame headers, checksums, scheduling, diagnostics, and fault management above the physical layer.

PCB implementation requires close attention to the LIN connection, supply decoupling, ground return, and protection network. Place the transceiver near the LIN connector, route the LIN trace away from sensitive analog and high-speed digital signals, provide a low-impedance ground path, and use the application guidance in the manufacturer datasheet for external protection and pull-up components. The 8-pin SOIC footprint is easy to route, but vehicle transceivers still require careful EMC-oriented layout.

This page consolidates the manufacturer product-page facts, distributor package information, interface requirements, design guidance, and qualification-aware replacement considerations into an engineering-focused reference for MC33662LEF selection and implementation.

Drop-in alternatifler için MC33662LEF — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller MC33662LEF (aynı form faktörü ve ayağa oturma) — farklı olan Package, Product Type.

NXP Semiconductors
Package: 8-SOIC, 0.154 in (3.90 mm) width
Product Type: 1/1 LIN bus transceiver
İle Karşılaştır MC33662LEF →

MC33662SEF

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
NXP Semiconductors
📦 8-pin SOIC
1/1 LIN bus transceiver · 1 channel · LIN bus · 100 kbps · 13.5 V · Yes · 8-SOIC, 0.154 in (3.90 mm) width · 8 pins

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

MC33662JEF

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
NXP Semiconductors
📦 8-pin SOIC
LIN Bus Physical-Layer Transceiver · 1 transmitter and 1 receiver · LINbus · 13.5 V · -40 °C · 125 °C · 8 pins · SOIC-8

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

MC33662LEF Özellikler

Product Type LIN physical-layer transceiver
Nominal LIN Data Rate 20 kbit/s
Fast Test and Programming Baud Rate 100 kbit/s
LIN Specification Compatibility LIN 2.x
Automotive Network Standard SAE J2602-2
Supply Voltage Range 7 V to 18 V
Controller Input Compatibility 3.3 V and 5.0 V
Transceiver Configuration 1/1 half-duplex LIN transceiver
Paket 8-pin SOIC
Package Family SOIC-8 surface-mount package
Montaj Türü Surface mount
Application Domain Automotive LIN sub-bus
Bus Type Single-wire Local Interconnect Network
RoHS Durumu unknown
REACH Status unknown
AEC-Q100 Qualification unknown

MC33662LEF Pin Yapısı

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 RXD — Receive data output from the LIN bus
Pin 2 GND — Ground connection
Pin 3 TXD — Transmit data input from the host controller
Pin 4 NC — Not connected
Pin 5 VCC — Logic supply connection
Pin 6 VSUP — Vehicle supply connection
Pin 7 GND — Ground connection
Pin 8 LIN — LIN bus transceiver connection

Tipik Uygulamalar

MC33662LEF için uygundur 6 uygulamas: Automotive Door Control Module, Automotive Lighting Controller, Climate Control Node, Seat and Switch Module, Automotive Sensor Gateway, Vehicle Test and Programming Interface.

🚗

Automotive Door Control Module

The MC33662LEF fits door-control nodes that exchange switch, motor-command, and sensor information over a 20 kbit/s LIN sub-bus. Its 7 V to 18 V operating range accommodates vehicle power environments, while 3.3 V and 5.0 V controller compatibility allows the same physical layer to serve different host MCU logic levels. Place the transceiver close to the connector, provide a low-impedance ground return, and use the manufacturer application circuit for the LIN pull-up and protection network. Its SAE J2602-2 and LIN 2.x support makes it appropriate for qualified body-network designs, subject to the exact device grade and vehicle specification.

💡

Automotive Lighting Controller

The MC33662LEF can connect a lighting controller to a LIN remote node that carries switching commands and diagnostic information. The 20 kbit/s L-series rate matches standard LIN communication, and the 7 V to 18 V supply range supports vehicle-level operation. The controller interface accepts 3.3 V or 5.0 V signals, simplifying integration with different MCU families. Keep the LIN trace short near the wiring connector, route it away from LED-driver switching nodes, and use a solid ground return to reduce susceptibility to conducted disturbances in the vehicle harness.

🏭

Climate Control Node

The MC33662LEF is appropriate for climate-control subsystems that distribute motor and sensor commands over a low-cost LIN network. Its LIN 2.x and SAE J2602-2 support aligns the physical layer with modern automotive sub-bus requirements, while the 20 kbit/s rate provides sufficient throughput for bounded control and diagnostic messages. The transceiver isolates the host controller from the physical LIN wiring, but software must still implement frame timing, checksum handling, and fault recovery. Position the device near the harness interface and protect the LIN route according to the NXP reference application.

🔧

Seat and Switch Module

The MC33662LEF suits compact seat, switch, and convenience modules where numerous distributed nodes need inexpensive communication. Its 20 kbit/s rate and single-wire LIN interface support deterministic command exchange without a full CAN network. The 7 V to 18 V supply operation aligns with vehicle electrical systems, while the selectable controller-side logic compatibility supports both 3.3 V and 5.0 V hosts. For low-current modules, verify sleep-current requirements and the complete external bus network in the manufacturer datasheet. Use short supply decoupling and route the LIN conductor away from switches and inductive loads.

🧩

Automotive Sensor Gateway

The MC33662LEF can serve as the LIN-facing element of a gateway that collects inputs from distributed automotive sensors and forwards status to a higher-level controller. LIN 2.x and SAE J2602-2 compatibility support use in modern vehicle sub-networks, and the 20 kbit/s L-series rate matches normal control traffic. The device accepts both 3.3 V and 5.0 V controller inputs, but logic thresholds and timing still require verification against the host MCU. Keep the transceiver close to the connector, provide an uninterrupted ground path, and implement software diagnostics for missing frames, bus shorts, and invalid headers.

🖥️

Vehicle Test and Programming Interface

The MC33662 family includes a 100 kbit/s mode for test and programming activities, making the MC33662LEF relevant to production and diagnostic interfaces that need more than the normal 20 kbit/s LIN traffic rate. Designers should distinguish this fast mode from ordinary LIN communication and verify the applicable baud-rate selection, timing, and host configuration in the manufacturer datasheet. The 8-pin SOIC package supports conventional surface mounting, while the 7 V to 18 V supply and 3.3 V or 5.0 V controller compatibility align with embedded test equipment and vehicle electronic modules.

What is the MC33662LEF?
The MC33662LEF is an automotive LIN physical-layer transceiver that operates at 20 kbit/s and is packaged in an 8-pin SOIC. According to the NXP MC33662 product page, it supports LIN 2.x and SAE J2602-2 networks. The device provides the interface between a host controller and the single-wire LIN bus, translating controller TXD and RXD signals into physical bus states.
What is the operating voltage range of MC33662LEF?
The MC33662LEF operates from a 7 V to 18 V vehicle supply. According to NXP product information for the MC33662 family, the controller-side interface accepts 3.3 V and 5.0 V input levels. Use the vehicle-bus supply for the transceiver's primary power input and verify all system rails against the manufacturer datasheet before finalizing the power architecture.
What LIN specifications does MC33662LEF support?
The MC33662LEF supports LIN 2.x and SAE J2602-2 physical-layer operation. According to the NXP MC33662 product page, it is dedicated to automotive LIN sub-bus applications. The L-series operating rate is 20 kbit/s, while the MC33662 family also includes a 100 kbit/s mode intended for test and programming operations rather than normal network traffic.
Where can I download the MC33662LEF datasheet PDF?
The official MC33662LEF documentation is available through NXP's MC33662 product page at https://www.nxp.com/products/MC33662. The package, electrical limits, pin descriptions, application information, and recommended external circuitry should be taken from the manufacturer datasheet. Use the exact ordering code MC33662LEF when checking device-specific marking, qualification, and revision information.
Where is the MC33662LEF pinout located?
The MC33662LEF pinout is defined by the pin-description table in the NXP MC33662 manufacturer datasheet. The component uses an 8-pin SOIC package. For PCB work, assign LIN, supply, ground, RXD, TXD, and no-connect positions exactly from that table rather than inferring them from another LIN transceiver, because package variants can use different functions or exposed connections.
Is the MC33662LEF suitable for automotive body modules?
The MC33662LEF is suitable for LIN-connected automotive body electronics because it supports LIN 2.x, SAE J2602-2, and a 7 V to 18 V supply range. Typical nodes include door, lighting, seat, climate, and switch modules. Final qualification still depends on the exact device revision, temperature grade, ESD requirements, and the vehicle manufacturer's component specification.
MC33662LEF vs MC33662BLEF - which one is the LIN transceiver?
The MC33662LEF is the documented 20 kbit/s LIN 2.x physical-layer transceiver in an 8-pin SOIC package. NXP search information also lists MC33662BLEF as a different family member associated with CAN functionality. Because the two descriptions do not establish identical protocol, pinout, and electrical ratings, MC33662BLEF should not be treated as a drop-in replacement for MC33662LEF.
Can MC33662SEF replace MC33662LEF?
No unconditional replacement should be made between the L and S speed selections because their nominal LIN baud rates differ. The MC33662LEF is the 20 kbit/s selection, while the S-series is intended for a different operating-rate class. If their SOIC pin assignments match, the different baud-rate requirement must still be checked against the LIN master schedule, oscillator configuration, and the manufacturer datasheet.
When should I choose MC33662LEF instead of another LIN transceiver?
Choose MC33662LEF when the design requires a 20 kbit/s LIN 2.x node with a 7 V to 18 V vehicle supply, 3.3 V or 5.0 V controller compatibility, and an 8-pin SOIC footprint. Select another device only when its supply range, logic thresholds, bus timing, fault behavior, qualification status, and exact pin assignments satisfy the vehicle interface requirements.
What is the best drop-in replacement for MC33662LEF?
No cross-manufacturer drop-in replacement is established by the available cross-reference information. A valid replacement must match the SOIC-8 footprint, pin functions, 20 kbit/s baud rate, 7 V to 18 V supply, logic thresholds, LIN electrical behavior, and automotive qualification. The NXP MC33662 family contains related selections, but speed and order-code differences must be reviewed before treating any variant as a replacement.
What can replace MC33662LEF in an existing design?
A device can replace MC33662LEF only after its manufacturer confirms pin-to-pin compatibility and equivalent electrical behavior. Check all eight SOIC positions, the LIN pin, both supply domains, RXD and TXD logic levels, sleep or wake behavior, bus timing, dominant-state behavior, ESD rating, and operating-temperature grade. A shared package alone is not sufficient evidence of drop-in compatibility.
How should the LIN bus PCB layout be designed for MC33662LEF?
Place the MC33662LEF close to the LIN connector and route the LIN trace as a short, controlled network segment away from sensitive analog and high-speed digital paths. Connect the transceiver ground to the vehicle ground through a low-impedance return, place supply bypassing at the appropriate power pins, and follow the manufacturer application circuit for the external pull-up and protection network.
Does MC33662LEF need an external pull-up resistor?
The complete LIN bus design normally includes the pull-up arrangement defined by the manufacturer application circuit and the system specification. The MC33662LEF provides the physical transceiver interface, but external network components, connector protection, and wiring details remain part of the board design. Follow the NXP datasheet values and application diagram rather than copying a resistor value from an unrelated LIN implementation.
Where can I buy MC33662LEF and check its price and lead time?
Use the Request a Quote form on this page to request MC33662LEF pricing, current availability, quantity breaks, and lead time. The 8-pin SOIC ordering code should be stated exactly on the request. The manufacturer part number and package suffix must match the assembled design, while quote confirmation should also establish minimum order quantity and production traceability requirements.
What are the key specifications of MC33662LEF that engineers should know?
The principal MC33662LEF specifications are a 20 kbit/s LIN data rate, LIN 2.x and SAE J2602-2 compatibility, a 7 V to 18 V supply range, 3.3 V and 5.0 V controller-input compatibility, and an 8-pin SOIC package. According to NXP product information, the MC33662 family also provides a 100 kbit/s test and programming mode. Verify detailed timing, protection, and qualification limits in the manufacturer datasheet.

Mühendislik referans verileri: MC33662LEF — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose MC33662LEF for a new 20 kbit/s LIN node that requires an 8-pin SOIC physical-layer transceiver, a 7 V to 18 V vehicle supply, and compatibility with 3.3 V or 5.0 V controller signals. MC33662SEF is relevant only when the network requires the slower 10 kbit/s selection; its 50% baud-rate difference can make it unsuitable even when the package matches. MC33662JEF belongs to another speed-selection family and should be chosen only after its exact timing and interface requirements match the LIN master. For an existing PCB, verify every pin function, logic threshold, supply connection, diagnostic behavior, and qualification grade rather than relying on the SOIC-8 outline alone.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün MC33662SEF MC33662JEF
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors
Product Type LIN physical-layer transceiver LIN physical-layer transceiver LIN physical-layer transceiver
LIN Compatibility LIN 2.x LIN 2.x LIN 2.x
Automotive Network Standard SAE J2602-2 SAE J2602-2 SAE J2602-2
Supply Voltage Range 7 V to 18 V 7 V to 18 V 7 V to 18 V
Controller Input Compatibility 3.3 V and 5.0 V 3.3 V and 5.0 V 3.3 V and 5.0 V
Fast Test and Programming Rate 100 kbit/s 100 kbit/s 100 kbit/s
RoHS Status unknown unknown unknown

Ana Farklılayıcılar

  • Standard 20 kbit/s LIN operating-rate selection (karşılaştırma:MC33662SEF)
  • Automotive physical-layer compatibility (karşılaştırma:MC33662JEF)
  • Controller integration flexibility (karşılaştırma:MC33662SEF)

Tasarım Notları

Place the MC33662LEF near the LIN connector and keep the LIN trace short and isolated from sensitive analog or high-speed digital paths. Route the vehicle ground return directly to the transceiver ground with a low-impedance path. Apply the manufacturer reference circuit for the external pull-up and protection components, and avoid long stubs that could increase bus-edge distortion.

Decouple the logic and vehicle-supply pins directly at the package according to the NXP application diagram. Keep high-current switching regulators and inductive components away from the transceiver supply pins, and verify the supply ramp, operating range, and any sleep-mode requirements in the manufacturer datasheet. The 7 V to 18 V input capability does not eliminate transient protection requirements for an automotive harness.

Do not select a family variant solely because it uses an 8-pin SOIC. MC33662LEF is the 20 kbit/s L-series selection, so nominal baud rate and pin configuration must match the LIN master and host design. Also verify logic thresholds, dominant-state behavior, diagnostic support, qualification grade, and temperature range before approving a replacement.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The available product information confirms automotive LIN use and SAE J2602-2 compatibility but does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.

İlgili Aramalar

MC33662LEF datasheet MC33662LEF datasheet pdf MC33662LEF pinout MC33662LEF equivalent MC33662LEF replacement MC33662LEF cross reference MC33662LEF price MC33662LEF stock NXP MC33662LEF MC33662LEF 20 kbit/s LIN transceiver MC33662LEF 8-SOIC automotive interface MC33662LEF body control module MC33662LEF vs MC33662SEF MC33662LEF automotive LIN bus what is MC33662LEF

İlgili Bileşenler ve Terimler

NXP Semiconductors MC33662LEF MC33662SEF MC33662JEF MC33662BLEF LIN transceiver LIN physical-layer transceiver Local Interconnect Network automotive bus transceiver interface IC semiconductor 20 kbit/s 100 kbit/s test mode LIN 2.x SAE J2602-2 3.3 V logic 5.0 V logic 7 V to 18 V supply single-wire network SOIC-8 SOIC family surface-mount package automotive body electronics TXD RXD
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle