MC33794DH - Electric Field Imaging Sensor Interface | NXP
Артикул: MC33794DH ✓ АктивенMC33794DH Обзор
An electric field imaging sensor interface is a specialized form of sensor interface IC used to connect an analog sensing structure to digital control and measurement electronics. The MC33794DH sits between external electrodes and a host processor or controller: it excites the electrodes, processes the field response, and communicates the detection result through logic-level signals. This category combines capacitive or electric-field sensing, excitation control, signal conditioning, and digital interfacing in one dedicated semiconductor.
The principal features include noncontact sensing, externally adjustable excitation frequency, logic-level input and output, low 7 mA supply current, and operation around a 120 kHz-optimized excitation point. The 44-HSOP package provides 44 external leads and an exposed thermal pad. The exposed pad supports heat transfer from the IC, while the wide-bodied package gives the external electrode and signal-routing connections adequate separation for a high-voltage sensing interface.
The internal operating concept is based on driving an electric field through connected electrodes and detecting the response produced when an object enters or leaves that field. The low-frequency sine-wave excitation provides the sensing energy, while the adjustable frequency allows the interface to be tuned for a particular electrode geometry, target dielectric characteristic, or measurement environment. Because the excitation frequency is established with an external resistor, component tolerance, parasitic capacitance, electrode area, and proximity to metal structures should be considered during circuit optimization.
Typical uses include touchless control panels, occupancy detection, liquid-level sensing, appliance controls, proximity sensing, and embedded capacitive measurement systems. The IC is especially useful when a design must detect a dielectric object without mechanical contact, where moving parts would be undesirable, or where contamination on a traditional sensing surface could affect reliability. External electrode design and calibration remain central to obtaining repeatable results.
A key design consideration is the separation between the high-voltage sensing interface and sensitive logic. Use the manufacturer pin-description table and recommended application schematic when assigning every pin, especially power, electrode outputs, logic inputs, and logic outputs. Place the frequency-setting resistor close to its specified device pin, provide stable supply decoupling, and route electrode connections away from sensitive analog and digital paths. The exposed pad must follow the manufacturer’s thermal and electrical land-pattern guidance.
This product record combines the electric-field sensing function, verified package and interface characteristics, sourcing information, and practical implementation guidance. It is intended to help engineers evaluate whether the MC33794DH fits a noncontact sensing architecture while recognizing that electrode geometry, frequency tuning, isolation, and application-specific calibration determine the achievable measurement performance.
Аналоги без доработки для MC33794DH — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Для этого товара нет аналогов без доработки.
Запросить аналогиMC33794DH Максимальные параметры и электрические характеристики
| Device Type | Electric field imaging device and sensor interface IC |
| Manufacturer | NXP Semiconductors |
| Primary Function | Noncontact electric-field object detection |
| Excitation Signal | Low-frequency sine wave |
| Optimized Excitation Frequency | 120 kHz |
| Frequency Adjustment | External resistor |
| Ток потребления | 7 mA |
| Input Interface | Logic input |
| Output Interface | Logic output |
| Sensor Interface | ISO9141 |
| Корпус | 44-HSOP |
| Корпус / Типоразмер | 44-BSSOP, 11.00 mm width, exposed pad |
| Lead Count | 44 leads |
| Тип монтажа | Surface mount |
| Packaging | Tube |
Руководство по цоколевке MC33794DH в корпусе 44-bssop, 11.00 mm width, exposed pad
Цоколевка для MC33794DH (корпус 44-bssop, 11.00 mm width, exposed pad). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для MC33794DH.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MC33794DH подходит для 8 применениеs: Noncontact Touch Control, Appliance User Interfaces, Occupancy Detection, Liquid Level Sensing, Proximity Sensing, Dielectric Object Recognition, Industrial Presence Sensing, Smart Home Control Surface.
Noncontact Touch Control
The MC33794DH fits a noncontact touch-control panel in which external electrodes create an electric field and a user approaches the sensing surface without mechanically touching it. Its logic output can report a detection event to a controller, while the adjustable low-frequency sine-wave excitation allows the circuit to be tuned around a 120 kHz-optimized operating point. The 7 mA supply current helps keep the sensing subsystem power demand controlled. Successful implementation still depends on electrode geometry, target dielectric properties, PCB isolation, and calibration because the IC detects a change in the complete field structure rather than a single fixed capacitance.
Рекомендуется
Appliance User Interfaces
The MC33794DH can support touch-free controls in household appliances where sealed panels, wear resistance, or hygienic operation matters. External electrodes placed behind a nonconductive panel allow the device to sense a finger or object approaching the user interface without exposing electrical contacts. The adjustable excitation frequency provides a tuning mechanism for the panel material and electrode geometry, while the logic interface supports connection to a control MCU. The design must account for the dielectric contribution of the panel and verify detection repeatability across the complete temperature and humidity range intended for the appliance.
Рекомендуется
Occupancy Detection
MC33794DH-based occupancy sensing can detect when a person enters or leaves a defined field, allowing equipment to operate only when space is occupied. The external electrodes establish the sensing region, and the IC’s active sine-wave excitation and logic output provide a compact interface for a controller. The 44-HSOP exposed-pad package supports thermal dissipation in a compact assembly, while the stated 7 mA supply current is useful when power budgeting a low-power monitoring subsystem. Deployment should include tests with stationary objects, moving people, adjacent metal structures, and the intended furniture because these factors can reshape the electric field and change detection sensitivity.
Рекомендуется
Liquid Level Sensing
The MC33794DH is suitable for exploratory noncontact liquid-level sensing where the liquid changes the dielectric or field conditions around an electrode structure. Because the device actively excutes the field and evaluates its response, it can form the sensing front end of a level-detection system rather than relying only on a passive capacitance measurement. The externally adjustable excitation permits tuning for the electrode arrangement and fluid interface. A production design should validate conductivity, container material, fill rate, temperature, and calibration drift, because the relationship between field response and liquid level depends on the complete physical system.
Рекомендуется
Proximity Sensing
A MC33794DH proximity sensor can detect objects approaching a sealed surface without exposing a conventional mechanical switch or exposed capacitive electrode. The sensor interface generates an adjustable low-frequency sine wave, drives external electrodes, and reports the sensed condition through a logic output. This arrangement is useful for automatic doors, cabinet controls, protective covers, and compact products where a mechanical opening may be undesirable. Sensitivity and selectivity depend strongly on electrode dimensions and nearby conductive objects, so the physical installation should be modeled and calibrated rather than copied without adjustment.
Рекомендуется
Dielectric Object Recognition
The MC33794DH can support dielectric object recognition when different target materials create distinguishable electric-field responses. Its adjustable excitation frequency gives the designer a way to tune the sensing condition for a particular electrode geometry and target, while logic-level signaling allows a controller to apply thresholds or classification rules. Compared with a simple fixed threshold detector, this arrangement can be refined through hardware tuning and firmware evaluation. Reliable recognition requires repeatable target orientation, controlled electrode spacing, and environmental compensation; the IC supplies the excitation and interface function but does not eliminate the need for application-specific characterization.
Рекомендуется
Industrial Presence Sensing
MC33794DH-based presence sensing can support industrial controls that need to detect hands, tools, or workpieces without relying on exposed contacts. The external-electrode architecture permits the sensing surface to be separated from the electronics, and the logic output provides a straightforward signal for a machine controller. Its 7 mA stated supply current is helpful in equipment where the sensing subsystem must coexist with a larger power budget, while the exposed pad assists heat transfer in the 44-HSOP assembly. For industrial use, validate detection against conductive fixtures, lubricants, debris, temperature changes, and the grounding conditions of the machine because all can alter field coupling.
Рекомендуется
Smart Home Control Surface
The MC33794DH can implement a concealed smart-home control surface by placing electrodes beneath a decorative panel and using the IC to detect a nearby touch. This avoids mechanical switches and can support clean, flush interfaces on kitchen appliances, cabinetry, or wall controls. The 120 kHz-optimized and externally adjustable excitation provides a basis for tuning the electrode network to the chosen panel material. A practical deployment should evaluate false triggers from moisture, moving conductive objects, and neighboring equipment. Firmware can apply thresholds and timing rules, but stable field behavior begins with controlled electrode geometry and careful grounding of the exposed-pad structure.
Рекомендуется
Справочные инженерные данные для MC33794DH — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар |
|---|---|
| Brand | NXP Semiconductors |
| Package | 44-HSOP with exposed pad |
| Device Type | Electric field imaging device and sensor interface IC |
| Supply Current | 7 mA |
| Excitation Signal | Low-frequency sine wave |
| Optimized Frequency | 120 kHz |
| Frequency Adjustment | External resistor |
| Input Interface | Logic input |
| Output Interface | Logic output |
| Sensor Interface | ISO9141 |
| Lead Count | 44 leads |
| Packaging | Tube |
Заметки по проектированию
Keep the external-electrode network and its associated routing physically separate from sensitive logic and low-level sensing paths. The sensing electrodes interact with stray capacitance, ground planes, cables, enclosure metal, and adjacent circuitry, so moving a trace or changing a ground reference can alter the response. Follow the manufacturer application layout, minimize exposed sensing-node area, and evaluate the complete installed enclosure because PCB-level geometry alone does not determine the final field behavior.
Do not treat the adjustable excitation as a free-running timing function. The external resistor influences an operating point optimized around 120 kHz, and tolerance, electrode capacitance, target materials, and PCB parasitics can shift the usable response. Select the resistance from the manufacturer guidance, measure the chosen network in its final mechanical assembly, and calibrate detection thresholds using expected targets and worst-case environmental conditions instead of relying on a bench setup with no enclosure.
Use the exposed pad according to the NXP manufacturer package drawing and recommended land pattern. The exposed pad can provide electrical as well as thermal functions, so it must not be left unconnected unless the application guidance specifically permits that arrangement. Provide a stable ground reference and adequate copper for heat spreading, inspect solder fillet quality after assembly, and verify the operating temperature at the hottest expected ambient condition. The 7 mA supply-current specification does not include heat contributed by external sensor-node loading.
Design the supply path for a 7 mA sensing IC while accounting separately for the external electrode network and any downstream logic. Use the manufacturer's specified supply range and bypass requirements rather than inferring them from the package or interface type. A quiet and stable supply reference helps preserve repeatable field measurements. If the sensing electrodes require additional circuitry, include its current, protection requirements, and startup behavior in the complete power budget instead of sizing the rail from the MC33794DH current alone.
Информация о соответствии
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement is identified for MC33794DH in the manufacturer and distributor product information. The manufacturer product page and current compliance declarations should be checked for the exact device revision before a regulated production release.