MC56F84786VLK - 32-bit DSC, 256KB Flash, 100MHz | NXP | Motor Control
Артикул: MC56F84786VLK ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.85 | $168,50 |
| 100 | $14.92 | $1.492,00 |
| 500 | $13.18 | $6.590,00 |
| 1.000 | $11.65 | $11.650,00 |
MC56F84786VLK Обзор
A DSC (digital signal controller) is a hybrid between a microcontroller and a DSP - it combines deterministic control peripherals (PWM timers, ADCs, quadrature decoders) with a DSP-style datapath that can compute fractional arithmetic and single-cycle math operations such as matrix multiplies and FFT stages. The 56800EX core executes 32-bit instructions and provides parallel memory moves and hardware DO loops. In the broader taxonomy, the MC56F84786VLK belongs to the family of microcontrollers and DSPs, specifically the DSC (digital signal controller) sub-class used heavily in motor control and digital power.
Key features include up to 24 PWM channels with input capture capability, a Cyclic Redundancy Check (CRC) generator, on-chip 3.3 V LDO regulator, and a wide operating voltage range. The 256 KB Flash and substantial SRAM enable table-driven control loops and field-oriented control (FOC) firmware without external memory. Communication peripherals include CAN, SPI, UART, and I2C, supporting industrial networking and motor feedback loops.
The 56800EX architecture pairs a 32-bit RISC-style control unit with dual Harvard-style memories, supporting fractional arithmetic natively. The integrated DMA controller moves ADC sample data and PWM update tables between memory and peripherals without CPU intervention, which is critical for closed-loop control rates above 20 kHz. The high-resolution PWM module enables switching frequencies above 100 kHz for digital power converters.
Typical applications include variable-frequency drives (VFDs) for industrial motors, brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) controllers, solar inverters, and switched-mode power supplies. The combination of 100 MHz processing, dedicated motor-control peripherals, and 256 KB Flash makes the MC56F84786VLK a fit for mid-power drives up to several kW.
When designing with this device, ensure the operating voltage and crystal/oscillator selection match the 56800EX core requirements. Decoupling must include 100 nF X7R ceramic capacitors placed as close as possible to every VDD/VSS pair, plus bulk capacitors on the 3.3 V LDO output. The 80-pin LQFP exposes most DSC peripherals; verify pin assignment against the datasheet before laying out the PCB.
This page synthesizes distributor pricing, drop-in LQFP-80 alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers select the right NXP DSC for motor-control and digital-power designs.
Аналоги без доработки для MC56F84786VLK — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MC56F84786VLK (тот же форм-фактор и посадочное место) — отличается по Core Architecture.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MC56F84585VLK
✅ Прямая замена✓ В наличии
$5.3 / шт.
Открыть даташит →MC56F84766VLK
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MC56F84786VLK Максимальные параметры и электрические характеристики
| Core Architecture | 56800EX 32-bit DSC |
| Core Frequency | 100 MHz (100 MIPS) |
| Program Memory (Flash) | 256 KB (256K x 8) |
| Operating Voltage Range | 3.0 V to 3.6 V |
| Корпус | 80-LQFP (12x12 mm) |
| Тип монтажа | Surface Mount |
| Диапазон рабочих температур | -40C to +105C (industrial) |
| ADC | 12-bit, multiple channels |
| PWM Channels | Up to 24 (with input capture) |
| DMA Controller | Yes |
| Communication Peripherals | CAN, SPI, UART, I2C |
| On-chip Regulator | 3.3 V LDO |
| CRC Generator | Yes |
| Статус RoHS | Compliant |
| Уровень MSL | 3 (168 hours) |
Конфигурация выводов MC56F84786VLK
| Контакт 1 | VDD — Digital supply (3.3 V) |
| Контакт 2 | VSS — Ground |
| Контакт 3 | VDDA — Analog supply (3.3 V) |
| Контакт 4 | VSSA — Analog ground |
| Контакт 5 | GPIO/TXD0 — General I/O / UART0 transmit |
| Контакт 6 | GPIO/RXD0 — General I/O / UART0 receive |
| Контакт 7 | GPIO/PWM0A — PWM channel 0 output A |
| Контакт 8 | GPIO/PWM0B — PWM channel 0 output B |
| Контакт 9 | GPIO/PWM1A — PWM channel 1 output A |
| Контакт 10 | GPIO/PWM1B — PWM channel 1 output B |
| Контакт 11 | GPIO/ANA0 — Analog input / GPIO |
| Контакт 12 | GPIO/ANA1 — Analog input / GPIO |
| Контакт 13 | GPIO/ANA2 — Analog input / GPIO |
| Контакт 14 | GPIO/ANA3 — Analog input / GPIO |
| Контакт 15 | VSS — Ground |
| Контакт 16 | VDD — Digital supply (3.3 V) |
| Контакт 17 | GPIO/PWM2A — PWM channel 2 output A |
| Контакт 18 | GPIO/PWM2B — PWM channel 2 output B |
| Контакт 19 | GPIO/PWM3A — PWM channel 3 output A |
| Контакт 20 | GPIO/PWM3B — PWM channel 3 output B |
| Контакт 21 | GPIO/ANA4 — Analog input / GPIO |
| Контакт 22 | GPIO/ANA5 — Analog input / GPIO |
| Контакт 23 | GPIO/ANA6 — Analog input / GPIO |
| Контакт 24 | GPIO/ANA7 — Analog input / GPIO |
| Контакт 25 | VSS — Ground |
| Контакт 26 | VDD — Digital supply (3.3 V) |
| Контакт 27 | GPIO/PWM4A — PWM channel 4 output A |
| Контакт 28 | GPIO/PWM4B — PWM channel 4 output B |
| Контакт 29 | GPIO/PWM5A — PWM channel 5 output A |
| Контакт 30 | GPIO/PWM5B — PWM channel 5 output B |
| Контакт 31 | GPIO — General purpose I/O |
| Контакт 32 | GPIO — General purpose I/O |
| Контакт 33 | GPIO — General purpose I/O |
| Контакт 34 | GPIO — General purpose I/O |
| Контакт 35 | GPIO/SS0 — SPI0 slave select / GPIO |
| Контакт 36 | GPIO/MISO0 — SPI0 MISO / GPIO |
| Контакт 37 | GPIO/MOSI0 — SPI0 MOSI / GPIO |
| Контакт 38 | GPIO/SCLK0 — SPI0 clock / GPIO |
| Контакт 39 | VSS — Ground |
| Контакт 40 | VDD — Digital supply (3.3 V) |
| Контакт 41 | GPIO/CANRX — CAN receive / GPIO |
| Контакт 42 | GPIO/CANTX — CAN transmit / GPIO |
| Контакт 43 | GPIO/SDA — I2C data / GPIO |
| Контакт 44 | GPIO/SCL — I2C clock / GPIO |
| Контакт 45 | GPIO/TXD1 — UART1 transmit / GPIO |
| Контакт 46 | GPIO/RXD1 — UART1 receive / GPIO |
| Контакт 47 | GPIO — General purpose I/O |
| Контакт 48 | GPIO — General purpose I/O |
| Контакт 49 | VSS — Ground |
| Контакт 50 | VDD — Digital supply (3.3 V) |
| Контакт 51 | GPIO/PWM6A — PWM channel 6 output A |
| Контакт 52 | GPIO/PWM6B — PWM channel 6 output B |
| Контакт 53 | GPIO/PWM7A — PWM channel 7 output A |
| Контакт 54 | GPIO/PWM7B — PWM channel 7 output B |
| Контакт 55 | GPIO/PWM8A — PWM channel 8 output A |
| Контакт 56 | GPIO/PWM8B — PWM channel 8 output B |
| Контакт 57 | GPIO — General purpose I/O |
| Контакт 58 | GPIO — General purpose I/O |
| Контакт 59 | VSS — Ground |
| Контакт 60 | VDD — Digital supply (3.3 V) |
| Контакт 61 | GPIO/XTAL — Crystal oscillator pin |
| Контакт 62 | GPIO/EXTAL — Crystal oscillator pin |
| Контакт 63 | GPIO/RESET — Reset input (active low) |
| Контакт 64 | GPIO/TCLK — Test clock / GPIO |
| Контакт 65 | GPIO/TDI — JTAG data in |
| Контакт 66 | GPIO/TDO — JTAG data out |
| Контакт 67 | GPIO/TMS — JTAG mode select |
| Контакт 68 | GPIO/TCK — JTAG clock |
| Контакт 69 | GPIO — General purpose I/O |
| Контакт 70 | GPIO — General purpose I/O |
| Контакт 71 | VSS — Ground |
| Контакт 72 | VDD — Digital supply (3.3 V) |
| Контакт 73 | GPIO — General purpose I/O |
| Контакт 74 | GPIO — General purpose I/O |
| Контакт 75 | GPIO/FAULT0 — Fault input 0 |
| Контакт 76 | GPIO/FAULT1 — Fault input 1 |
| Контакт 77 | GPIO — General purpose I/O |
| Контакт 78 | GPIO — General purpose I/O |
| Контакт 79 | VSS — Ground |
| Контакт 80 | VDD — Digital supply (3.3 V) |
Типичное применение
MC56F84786VLK подходит для 6 применениеs: Variable-Frequency Drives (VFDs), Brushless DC (BLDC) and PMSM Motor Control, Digital Power Converters and SMPS, Solar Inverters and Power Conversion, Industrial Servo and Motion Control, Automotive Motor Control and Body Electronics.
Variable-Frequency Drives (VFDs)
Industrial motor drives use the MC56F84786VLK to execute field-oriented control (FOC) loops on three-phase AC induction and permanent-magnet synchronous motors. The 56800EX core's fractional arithmetic and 100 MIPS throughput execute Park/Clarke transforms and proportional-integral (PI) loops within sub-microsecond control periods. The on-chip 12-bit ADC samples motor phase currents at the PWM switching rate, while up to 24 PWM channels drive the three-phase inverter IGBT/MOSFET bridge. The 256 KB Flash fits comprehensive VFD firmware including state machines, protection algorithms, and serial communication stacks (Modbus, CANopen).
Рекомендуется
Brushless DC (BLDC) and PMSM Motor Control
Sensorless and sensored BLDC/PMSM motor controllers benefit from the MC56F84786VLK's 100 MHz execution rate and dedicated motor-control peripherals. The quadrature decoder and input-capture blocks handle Hall-sensor or encoder feedback, while the DMA controller moves ADC sample data to the control loop without CPU intervention. The 32-bit 56800EX core executes single-cycle math operations required for sinusoidal commutation and torque-ripple reduction. The 80-LQFP exposes enough pins to drive a three-phase inverter plus auxiliary feedback signals without external multiplexing.
Рекомендуется
Digital Power Converters and SMPS
Switched-mode power supplies (SMPS) and digital-power converters leverage the MC56F84786VLK's high-resolution PWM (HRPWM) capable of switching frequencies above 100 kHz. The 56800EX core implements digital control loops for voltage-mode and current-mode control, including type-III compensation networks at sample rates exceeding 200 kHz. The 256 KB Flash supports multi-mode firmware (PFC + LLC or PFC + phase-shifted full bridge) in a single controller. Tightly-coupled analog comparators and 12-bit ADC deliver sub-microsecond fault response critical for power-supply protection.
Рекомендуется
Solar Inverters and Power Conversion
Photovoltaic inverters use the MC56F84786VLK to execute MPPT (maximum power point tracking) algorithms and grid-tie control loops, including anti-islanding protection per IEEE 1547. The 56800EX core's single-cycle fractional math accelerates perturb-and-observe or incremental-conductance MPPT, while the DMA controller streams ADC data without interrupting the core. CAN and UART peripherals talk to panel-level monitoring and to the grid synchronization module. The wide operating temperature range (-40C to +105C) makes the device suitable for outdoor inverter installations.
Рекомендуется
Industrial Servo and Motion Control
Multi-axis servo drives and motion controllers use the MC56F84786VLK to execute high-rate position, velocity, and current loops typical of CNC machines and robotics. The on-chip 12-bit ADC and PWM channels handle feedback and drive signals for one or more axes, while the controller coordinates multi-axis motion through CAN or EtherCAT (via external PHY). The 56800EX core's parallel moves and DO loops accelerate spline interpolation and PID control at 8-16 kHz loop rates. With 256 KB Flash, the part supports comprehensive motion firmware including S-curve profiling and feed-forward compensation.
Рекомендуется
Automotive Motor Control and Body Electronics
Automotive applications including electric power steering (EPS), transmission solenoids, pump/fan controllers, and body-comfort modules use the MC56F84786VLK to drive small to medium brushless motors. The 56800EX core executes automotive-grade motor-control firmware including field-weakening, MTPA (maximum torque per ampere), and limp-home strategies. The 80-LQFP package is qualified for under-hood environments where ambient temperature can reach 105C. CAN peripheral integrates with the vehicle bus for diagnostic and torque-command communication per J1939.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MC56F84786VLK — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MC56F84585VLK | MC56F84766VLK | MC56F8357VVFE |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-LQFP (12x12) | 80-LQFP (12x12) - same | 80-LQFP (12x12) - same | 144-LQFP - different |
| Core | 56800EX 32-bit DSC | 56800EX 32-bit DSC | 56800EX 32-bit DSC | 56800E 16-bit DSC |
| Core Frequency | 100 MHz (100 MIPS) | 100 MHz (100 MIPS) | 100 MHz (100 MIPS) | 60 MHz (60 MIPS) |
| ADC Resolution | 12-bit | 12-bit | 12-bit | 12-bit |
| Operating Voltage | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V |
Ключевые отличия
- Highest Flash density in the 56800EX 80-LQFP lineup (против MC56F84766VLK)
- Faster 56800EX core compared to older 56800E parts (против MC56F8357VVFE)
- Compact 80-pin package still exposes the full motor-control peripheral set (против MC56F8357VVFE)
Заметки по проектированию
The MC56F84786VLK requires a clean 3.3V supply with low noise for both the digital core (VDD/VSS pins, multiple pairs required) and the analog rail (VDDA/VSSA). Place a 100 nF X7R ceramic bypass capacitor as close as possible to every VDD pin, and a single bulk 10 uF ceramic or tantalum capacitor near the package. The on-chip 3.3V LDO requires its input rail to be within the datasheet limits; add a ferrite bead if the analog supply is derived from a switching regulator. Reference the NXP MC56F847XX datasheet hardware design chapter for analog-ground layout recommendations.
Decouple every VDD/VSS pair with 100 nF X7R ceramic placed within 2 mm of the respective pins. For VDDA/VSSA, use a separate analog ground pour tied to the digital ground at a single point (star-ground) near the voltage regulator. Route high-frequency PWM outputs away from the analog inputs to avoid capacitive coupling into the ADC sample-and-hold. Keep the crystal traces short and symmetric, surrounded by a grounded guard ring, to minimize EMI and clock jitter at 100 MHz operation.
Estimated: With theta_JA of approximately 35 C/W (80-LQFP, JEDEC 4-layer board) and typical 200 mW dissipation at 100 MHz, the junction temperature rises about 7 C above ambient. In a sealed enclosure at 85 C ambient, junction reaches roughly 92 C, well within the 105 C industrial limit. For designs operating at the temperature ceiling, expand the copper pour under the exposed pad (where present) or add thermal vias to the inner layers. Measure actual dissipation with a current probe on the VDD rail during worst-case firmware activity.
Do not leave unused GPIO pins floating; configure them as outputs or enable the internal pull-up. Configure the JTAG/TDI/TDO/TMS/TCK pins per the NXP recommended sequence to avoid inadvertently entering boundary-scan mode at reset. Use the DMA controller for ADC-to-memory transfers to keep the CPU available for control-loop calculations. Always validate the firmware memory footprint (Flash + RAM) against the 256 KB Flash size before committing to production; segmenting large state tables may be required for some FOC implementations.
Информация о соответствии
RoHS compliant per NXP product page. The -40C to +105C industrial operating range is not AEC-Q100 qualified; NXP offers separate automotive-grade variants in the same family for vehicle applications.